The No. 2 air conditioning radiator damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (in normal or reverse) based on these signals to move the No. 2 air conditioning radiator damper servo sub-assembly to the appropriate position, which controls the rear air outlet switching.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| B1449/49 | Rear Air Outlet Damper Control Servo Motor Circuit | Rear air outlet damper position sensor value does not change even if air conditioning amplifier assembly operates No. 2 air conditioning radiator damper servo sub-assembly | ·
No. 2 air conditioning radiator damper servo sub-assembly ·
Air conditioning harness assembly ·
Air conditioning amplifier assembly |
Memorized
(30 seconds or more) |
- |
The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the parentheses.
When the servo motor or air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization.
Confirm that no mechanical problem is present because this DTC can be output when either a damper link or the damper is mechanically locked.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Operate the mode switch.
Enter the following menus: Body Electrical / Air Conditioner / Data List.
Check the value(s) by referring to the table below.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Air Outlet Servo Pulse (R) | No. 2 air conditioning radiator damper servo sub-assembly (rear mode) target pulse | Min.: 128
Max.: 383 |
FACE: 253 (pulse)
B/L: 264 (pulse) SHUT: 276 (pulse) |
·
Displayed between 253 and 276 pulse ·
No. 2 air conditioning radiator damper servo sub-assembly (rear mode) system malfunction |
| Air Outlet Servo Actual Pls(R) | No. 2 air conditioning radiator damper servo sub-assembly (rear mode) actual pulse | Min.: 128
Max.: 383 |
FACE: 253 (pulse)
B/L: 264 (pulse) SHUT: 276 (pulse) |
·
Displayed between 253 and 276 pulse ·
No. 2 air conditioning radiator damper servo sub-assembly (rear mode) system malfunction |
| Tester Display |
|---|
| Air Outlet Servo Pulse (R) |
| Air Outlet Servo Actual Pls(R) |
When the mode switch is operated, the actual pulse changes following the target pulse.
| Result | Proceed to |
|---|---|
| Target pulse and actual pulse do not change | A |
| Target pulse changes but actual pulse does not change | B |
| Actual pulse changes following the target pulse (When troubleshooting according to the DTC) | C |
| Actual pulse changes following the target pulse (When troubleshooting according to Problem Symptoms Table) | D |
A
B
C
D
Replace the No. 2 air conditioning radiator damper servo sub-assembly (rear mode).
Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.
Clear the DTCs.
Check for DTCs.
DTC B1449/49 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the air conditioning harness assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY
Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.
Clear the DTCs.
Check for DTCs.
DTC B1449/49 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Check for DTCs.
DTC B1449/49 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG