Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › 2015.06–2016.03
RM3250E _59 Vehicle Exterior _038076 WIPER / WASHER _0184382 WIPER AND WASHER SYSTEM Y

WIPER / WASHER  WIPER AND WASHER SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the wiper and washer system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points for problem analysis:

What Vehicle model, system name
When Date, time, occurrence frequency
Where Road conditions
Under what conditions? Driving conditions, weather conditions
How did it happen? Problem symptoms



Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V


HINT:
·

A simple method to determine whether the battery is discharged is to operate the horn.

·

If the voltage is below 11 V, recharge or replace the battery before proceeding.




b.

Check the fuses and relays.


c.

Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


Result:
Proceed to
NEXT



NEXT

4.CHECK VEHICLE TYPE
4.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
w/o Headlight Cleaner System A
w/ Headlight Cleaner System B



A

5.PROBLEM SYMPTOMS TABLE

B

9.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
5.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in problem symptoms table A
Fault is listed in problem symptoms table B



A

6.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

6.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

7.ADJUST, REPAIR OR REPLACE
7.ADJUST, REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

8.CONFIRMATION TEST
8.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END

9.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
CAN DTC is not output A
CAN DTC is output B



A

10.CHECK FOR DTC*

B

10.CHECK FOR DTC*
a.

Check for DTCs.

Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DTC CHECK / CLEAR

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361

b.

Clear the DTCs.

Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DTC CHECK / CLEAR

Body Electrical > HL AutoLeveling > Clear DTCs
50002 361

c.

Recheck for DTCs.

Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DTC CHECK / CLEAR

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361

Result:
Result Proceed to
DTC is not output A
DTC is output (w/ Automatic Headlight Beam Lebeling Control System) B
DTC is output (w/o Automatic Headlight Beam Lebeling Control System) C



A

5.PROBLEM SYMPTOMS TABLE

B

C