Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)
RM3250E _58 Vehicle Interior _038064 DOOR LOCK _0184499 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)  No Answer-Back  


DESCRIPTION

In some cases, wireless door lock control functions are normal but the hazard warning light answer-back function does not operate. In such cases, hazard warning light signal outputs from the body ECU may be malfunctioning.

WIRING DIAGRAM

E322036E04
6.104,5.188 6.865,5.396 0.76,0.208 10 false Body ECU 3.01,0.958 6.219,1.198 3.208,0.24 10 false Combination Meter Assembly 3.01,0.802 3.563,1 0.552,0.198 10 false G11 3.906,0.563 4.458,0.76 0.552,0.198 10 false HAZ 4.344,0.427 4.896,0.625 0.552,0.198 10 false 2 5.771,0.427 6.323,0.625 0.552,0.198 10 false 6 6.021,0.438 6.573,0.635 0.552,0.198 10 false HAZ 6.031,1.427 6.583,1.625 0.552,0.198 10 false LSWD 6.031,2.49 6.583,2.688 0.552,0.198 10 false LSWP 2.604,3.177 5.896,3.375 3.292,0.198 10 false Front Door Lock Assembly RH*1 or LH*2 0.125,2.125 3.333,2.365 3.208,0.24 10 false Front Door Lock Assembly LH*1 or RH*2 0.125,1.948 1.698,2.146 1.573,0.198 10 false K1*1, J1*2 2.604,3 4.177,3.198 1.573,0.198 10 false J1*1, K1*2 0.344,1.448 1.917,1.646 1.573,0.198 10 false 7*1, 8*2 4.438,2.49 6.01,2.688 1.573,0.198 10 false 7*1, 8*2 2.042,1.438 3.615,1.635 1.573,0.198 10 false 8*1, 7*2 2.74,2.5 4.313,2.698 1.573,0.198 10 false 8*1, 7*2 6.094,5.01 6.646,5.208 0.552,0.198 10 false G27 5.719,1.438 6.271,1.635 0.552,0.198 10 false 15 5.792,2.49 6.344,2.688 0.552,0.198 10 false 2 5.469,3.219 6.167,3.417 0.698,0.198 10 false *3 0.375,4.365 3.583,4.604 3.208,0.24 10 false Rear Door Lock Assembly LH*3 2.781,5.167 5.99,5.406 3.208,0.24 10 false Rear Door Lock Assembly RH*3 0.375,4.208 0.927,4.406 0.552,0.198 10 false M1 2.781,5.021 3.333,5.219 0.552,0.198 10 false L1 0.948,1.448 1.49,1.615 0.542,0.167 10 false E 1.542,1.448 2.323,1.635 0.781,0.188 10 false LSSR 3.948,2.5 4.729,2.688 0.781,0.188 10 false LSSR 1.563,3.75 2.344,3.938 0.781,0.188 10 false LSSR 3.969,4.573 4.75,4.76 0.781,0.188 10 false LSSR 3.354,2.51 3.896,2.677 0.542,0.167 10 false E 0.948,3.75 1.49,3.917 0.542,0.167 10 false E 3.344,4.573 3.885,4.74 0.542,0.167 10 false E 2.031,3.75 2.583,3.948 0.552,0.198 10 false 6 4.427,4.573 4.979,4.771 0.552,0.198 10 false 6 0.76,3.75 1.313,3.948 0.552,0.198 10 false 9 3.156,4.573 3.708,4.771 0.552,0.198 10 false 9 0.156,5.656 1.094,5.854 0.938,0.198 10 false *1: for LHD 0.146,6.021 2.167,6.25 2.021,0.229 10 false *2: for RHD 0.156,6.385 2.177,6.615 2.021,0.229 10 false *3: for Double Cab

CAUTION / NOTICE / HINT

NOTICE:
·

If the body ECU has been replaced, it is necessary to initialize the body ECU.*1

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.*2

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION

*1: w/ Automatic Light Control System

*2: w/ Door Control Battery




PROCEDURE

1.CHECK HAZARD WARNING LIGHTS OPERATION
a.

Check that the hazard warning light blinks when the hazard warning signal switch is pressed.

OK:

Hazard warning light signal is normal.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY ECU)

NG

GO TO LIGHTING SYSTEM (PROCEED TO HAZARD WARNING SWITCH CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY ECU)
a.

Disconnect the G11 combination meter assembly connector.


b.

Disconnect the G27 body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G11-2 (HAZ) - G27-6 (HAZ) Always Below 1 Ω
G11-2 (HAZ) or G27-6 (HAZ) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT DOOR LOCK ASSEMBLY (DETECTION UNLOCK SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT DOOR LOCK ASSEMBLY (DETECTION UNLOCK SWITCH)

*: for Double Cab

a.

for Front Side:

i.

Remove the front door lock assembly.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL


ii.

Inspect the front door lock assembly.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION



b.

for Rear Side*:

i.

Remove the rear door lock assembly.

Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK(for Double Cab)>REMOVAL


ii.

Inspect the rear door lock assembly.

Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK(for Double Cab)>INSPECTION



Result:
Result Proceed to
OK A
NG (for Front Side) B
NG (for Rear Side) C



A

4.CHECK HARNESS AND CONNECTOR (DOOR LOCK ASSEMBLY - BODY ECU AND BODY GROUND)

B

REPLACE FRONT DOOR LOCK ASSEMBLY

C

REPLACE REAR DOOR LOCK ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (DOOR LOCK ASSEMBLY - BODY ECU AND BODY GROUND)

*1: for LHD

*2: for RHD

*3: for Double Cab


a.

for Driver Side:

i.

Disconnect the K1*1 or J1*2 front door lock assembly LH*1 or RH*2 connector.


ii.

Disconnect the G27 body ECU connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
K1-8 (LSSR) - G27-15 (LSWD) Always Below 1 Ω
K1-7 (E) - Body ground Always Below 1 Ω
K1-8 (LSSR) or G27-15 (LSWD) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
J1-7 (LSSR) - G27-15 (LSWD) Always Below 1 Ω
J1-8 (E) - Body ground Always Below 1 Ω
J1-7 (LSSR) or G27-15 (LSWD) - Body ground Always 10 kΩ or higher




b.

except Driver Side:

i.

Disconnect the J1*1 or K1*2 front door lock assembly RH*1 or LH*2 connector.


ii.

Disconnect the L1 rear door lock assembly RH connector*3.


iii.

Disconnect the M1 rear door lock assembly LH connector*3.


iv.

Disconnect the G27 body ECU connector.


v.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
J1-7 (LSSR) - G27-2 (LSWP) Always Below 1 Ω
J1-8 (E) - Body ground Always Below 1 Ω
J1-7 (LSSR) or G27-2 (LSWP) - Body ground Always 10 kΩ or higher
L1-6 (LSSR) - G27-2 (LSWP)*3 Always Below 1 Ω
L1-9 (E) - Body ground*3 Always Below 1 Ω
L1-6 (LSSR) or G27-2 (LSWP) - Body ground*3 Always 10 kΩ or higher
M1-6 (LSSR) - G27-2 (LSWP)*3 Always Below 1 Ω
M1-9 (E) - Body ground*3 Always Below 1 Ω
M1-6 (LSSR) or G27-2 (LSWP) - Body ground*3 Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
K1-8 (LSSR) - G27-2 (LSWP) Always Below 1 Ω
K1-7 (E) - Body ground Always Below 1 Ω
K1-8 (LSSR) or G27-2 (LSWP) - Body ground Always 10 kΩ or higher
L1-6 (LSSR) - G27-2 (LSWP)*3 Always Below 1 Ω
L1-9 (E) - Body ground*3 Always Below 1 Ω
L1-6 (LSSR) or G27-2 (LSWP) - Body ground*3 Always 10 kΩ or higher
M1-6 (LSSR) - G27-2 (LSWP)*3 Always Below 1 Ω
M1-9 (E) - Body ground*3 Always Below 1 Ω
M1-6 (LSSR) or G27-2 (LSWP) - Body ground*3 Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR