Home › Engine / Hybrid System › 2TR-FE ENGINE MECHANICAL › CYLINDER HEAD GASKET
RM3250E _51 Engine / Hybrid System _038022 2TR-FE ENGINE MECHANICAL _0184665 CYLINDER HEAD GASKET A

2TR-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  INSTALLATION  


PROCEDURE

Hide 11115 1.INSTALL CYLINDER HEAD GASKET

a.

Clean and degrease the contact surfaces of the cylinder head sub-assembly and cylinder block sub-assembly.


b.
A337677C01
2.458,0.969 2.75,0.323 2.75,0.323 2.896,0.323 true 0.406,1.24 0.552,1.24 0.552,1.24 0.75,0.833 false 0.208,1.146 0.417,1.333 0.208,0.188 10 false *1 2.365,1.5 2.552,1.698 0.188,0.198 10 false *a 3.156,0.948 3.365,1.156 0.208,0.208 10 false *b 1.229,0.677 1.542,0.833 0.313,0.156 10 false *c 1.219,3.042 1.427,3.24 0.208,0.198 10 false *d 2.781,3.031 2.99,3.219 0.208,0.188 10 false *e 0.677,0.271 0.99,0.427 0.313,0.156 10 false *f 2.938,2.552 3.135,2.781 0.198,0.229 10 false *g 2.938,0.219 3.125,0.417 0.188,0.198 10 false *a 2.104,0.448 2.302,0.677 0.198,0.229 10 false *g
*1 Cylinder Head Gasket
*a 7.0 to 9.0 mm (0.276 to 0.354 in.)
*b 5.0 to 7.0 mm (0.197 to 0.276 in.)
*c 3.0 to 5.0 mm (0.118 to 0.197 in.)
*d 166.25 mm (6.55 in.)
*e 62.25 mm (2.46 in.)
*f Side View
*g View A


Apply seal packing to a new cylinder head gasket as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207 B or equivalent


NOTICE:
·

Be sure to clean and degrease the contact surfaces.

·

Apply seal packing to the bead on the cylinder head gasket.

·

Install the cylinder head gasket within 3 minutes and tighten the cylinder head set bolts within 15 minutes after applying seal packing.




c.
A302545C05
0.521,0.49 0.802,0.198 0.802,0.198 1.01,0.198 true 1.042,0.094 1.219,0.292 0.177,0.198 10 false *a
*a Lot No.
V100135

Front


Place the cylinder head gasket on the cylinder block surface with the lot No. stamp facing upward.

NOTICE:
·

Remove any oil from the contact surface.

·

Make sure that the cylinder head gasket is installed in the correct direction.




Hide 11101 2.INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
·

Perform "Inspection After Repairs" after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION

·

The cylinder head set bolts are tightened in 3 successive steps.



a.

Place the cylinder head sub-assembly on the cylinder block sub-assembly.

NOTICE:
·

Make sure that no oil is on the mounting surface of the cylinder head sub-assembly.

·

Place the cylinder head sub-assembly on the cylinder block gently so as not to damage the gasket with the bottom part of the head.




b.

Install the plate washers to the cylinder head set bolts.


c.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.


d.
A302544N10
1.75,0.271 1.906,0.469 0.156,0.198 10 true 1 1.771,1.781 1.906,1.958 0.135,0.177 10 true 2 2.375,0.26 2.531,0.458 0.156,0.198 10 true 3 1.135,1.792 1.292,1.99 0.156,0.198 10 true 4 2.396,1.781 2.552,1.979 0.156,0.198 10 false 5 1.146,0.26 1.302,0.458 0.156,0.198 10 false 6 2.979,1.781 3.135,1.979 0.156,0.198 10 true 7 0.51,0.26 0.667,0.458 0.156,0.198 10 true 8 2.979,0.24 3.135,0.438 0.156,0.198 10 true 9 0.49,1.792 0.719,2.01 0.229,0.219 10 true 10

Step 1:

Using several steps, install and uniformly tighten the 10 cylinder head set bolts with plate washers in the sequence shown in the illustration.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


e.

Mark the front of each cylinder head set bolt head with paint.


f.

Step 2:

Tighten the cylinder head set bolts 90° in the sequence shown in step 1.


g.

Step 3:

Tighten the cylinder head set bolts another 90° in the sequence shown in step 1.


h.

Check that the paint marks are now at a 180° angle to the front.


i.

w/ Oil Cooler:

Connect the No. 4 water by-pass pipe with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 3.CONNECT ENGINE WIRE

a.
A346843C01
2.219,1.99 2.417,1.99 2.417,1.99 2.615,1.573 true 2.313,0.844 2.51,1.052 0.198,0.208 10 true *a 2.031,1.906 2.219,2.094 0.188,0.188 10 true *b 1.25,1.146 1.521,1.333 0.271,0.188 10 true 45° 0.594,1.146 0.865,1.333 0.271,0.188 10 true 45° 0.479,0.271 0.615,0.448 0.135,0.177 10 true A 1.875,0.063 2.01,0.24 0.135,0.177 10 true A 0.156,1.969 0.292,2.146 0.135,0.177 10 true B
*a INCORRECT
*b Do not Allow Wires to Overlap


Connect the engine wire to the cylinder head sub-assembly with the 3 bolts so that it is within the specified range shown in the illustration.

Torque:
for bolt A : 25 N*m (255 kgf*cm, 18 ft.*lbf)
for bolt B : 30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 13716 4.INSTALL VALVE STEM CAP

a.

Apply a light coat of engine oil to the valve stem ends.


b.

Install the 16 valve stem caps to the cylinder head sub-assembly.

NOTICE:

Do not drop the valve stem caps into the cylinder head sub-assembly.



Hide 13750 5.INSTALL VALVE LASH ADJUSTER ASSEMBLY

a.

Inspect each valve lash adjuster assembly before installing it.

Click hereEngine / Hybrid System>2TR-FE ENGINE MECHANICAL>ENGINE UNIT>INSPECTION


b.

Install the 16 valve lash adjuster assemblies to the cylinder head sub-assembly.

NOTICE:

Install each valve lash adjuster assembly to the same place it was removed from.



Hide 13801 6.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Apply clean engine oil to the valve lash adjuster assembly tips and valve stem cap surfaces.


b.
A336446C01
0.552,0.802 0.74,0.802 0.74,0.802 0.969,0.552 false 0.927,1.25 1.094,1.25 1.094,1.25 1.323,1.021 true 0.938,3.021 1.094,3.021 1.094,3.021 1.313,2.771 true 0.677,2.531 0.865,2.531 0.865,2.531 1.094,2.281 false 1.948,0.375 2.156,0.188 2.156,0.188 2.365,0.188 false 1.917,2.167 2.125,1.979 2.125,1.979 2.333,1.979 true 0.365,0.708 0.552,0.906 0.188,0.198 10 false *1 0.729,1.146 0.927,1.333 0.198,0.188 10 false *2 2.406,0.094 2.625,0.281 0.219,0.188 10 false *3 0.063,0.063 0.26,0.271 0.198,0.208 10 false *a 0.063,1.885 0.25,2.083 0.188,0.198 10 false *b 0.479,2.427 0.667,2.625 0.188,0.198 10 false *1 0.74,2.917 0.938,3.104 0.198,0.188 10 false *2 2.375,1.885 2.594,2.073 0.219,0.188 10 false *3
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem Cap
*a INCORRECT
*b CORRECT


Install the 16 No. 1 valve rocker arm sub-assemblies as shown in the illustration.

NOTICE:

Install the valve stem cap, valve lash adjuster assembly and No. 1 valve rocker arm sub-assembly to the same places they were removed from.



Hide 13511 7.INSTALL CAMSHAFT

HINT:

Perform "Inspection After Repairs" after replacing the camshaft or No. 2 camshaft.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A336456N01
0.313,1.521 0.469,1.719 0.156,0.198 10 false B 0.302,0.208 0.458,0.406 0.156,0.198 10 false A 1.979,0.219 2.135,0.417 0.156,0.198 10 false C 1.99,1.51 2.146,1.708 0.156,0.198 10 false D 1.125,2.844 1.281,3.042 0.156,0.198 10 false A 1.781,2.5 1.938,2.698 0.156,0.198 10 false B 2.719,3.563 2.906,3.813 0.188,0.25 10 true C 3.063,3.219 3.24,3.458 0.177,0.24 10 true D

Apply clean engine oil to the camshaft cams and cylinder head sub-assembly journals.


b.

Position the camshaft and No. 2 camshaft as shown in the illustration.


c.
A336446C01
0.552,0.802 0.74,0.802 0.74,0.802 0.969,0.552 false 0.927,1.25 1.094,1.25 1.094,1.25 1.323,1.021 true 0.938,3.021 1.094,3.021 1.094,3.021 1.313,2.771 true 0.677,2.531 0.865,2.531 0.865,2.531 1.094,2.281 false 1.948,0.375 2.156,0.188 2.156,0.188 2.365,0.188 false 1.917,2.167 2.125,1.979 2.125,1.979 2.333,1.979 true 0.365,0.708 0.552,0.906 0.188,0.198 10 false *1 0.729,1.146 0.927,1.333 0.198,0.188 10 false *2 2.406,0.094 2.625,0.281 0.219,0.188 10 false *3 0.063,0.063 0.26,0.271 0.198,0.208 10 false *a 0.063,1.885 0.25,2.083 0.188,0.198 10 false *b 0.479,2.427 0.667,2.625 0.188,0.198 10 false *1 0.74,2.917 0.938,3.104 0.198,0.188 10 false *2 2.375,1.885 2.594,2.073 0.219,0.188 10 false *3
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem Cap
*a INCORRECT
*b CORRECT


Make sure that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.


Hide 8.INSTALL CAMSHAFT BEARING CAP

a.
A336457

Temporarily install the No. 1 camshaft bearing cap.


b.

Confirm the location for each No. 2 camshaft bearing cap and install each one to the proper location.


c.

Uniformly temporarily install the 20 bolts while keeping the camshaft level.


d.
A336452N02
0.458,0.156 0.656,0.344 0.198,0.188 10 true 20 0.448,1.885 0.646,2.083 0.198,0.198 10 true 19 0.135,0.656 0.323,0.844 0.188,0.188 10 true 18 0.156,1.458 0.344,1.646 0.188,0.188 10 true 17 2.771,0.219 2.979,0.417 0.208,0.198 10 true 16 3.042,1.063 3.25,1.25 0.208,0.188 10 true 15 2.771,1.823 2.969,2.01 0.198,0.188 10 true 14 2.552,0.948 2.76,1.125 0.208,0.177 10 true 13 0.938,0.219 1.156,0.406 0.219,0.188 10 true 12 1.125,1.104 1.333,1.281 0.208,0.177 10 true 11 0.938,1.802 1.135,2 0.198,0.198 10 true 10 0.74,0.948 0.854,1.125 0.115,0.177 10 true 9 2.208,0.219 2.344,0.417 0.135,0.198 10 true 8 2.406,1.115 2.531,1.292 0.125,0.177 10 true 7 2.198,1.823 2.344,2.021 0.146,0.198 10 true 6 1.99,0.948 2.115,1.125 0.125,0.177 10 true 5 1.604,0.219 1.729,0.406 0.125,0.188 10 true 4 1.771,1.104 1.906,1.281 0.135,0.177 10 true 3 1.594,1.823 1.74,2.021 0.146,0.198 10 true 2 1.354,0.938 1.49,1.125 0.135,0.188 10 true 1

Tighten the 20 bolts in the order shown in the illustration.

Torque:
15.5 N*m (158 kgf*cm, 11 ft.*lbf)


Hide 13561 9.INSTALL NO. 1 CHAIN VIBRATION DAMPER

Hide 13506 10.INSTALL CHAIN SUB-ASSEMBLY

Hide 13559 11.INSTALL CHAIN TENSIONER SLIPPER

Hide 13540 12.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13566B 13.INSTALL TIMING CHAIN GUIDE

Hide 14.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 11204 15.INSTALL CYLINDER HEAD COVER CONNECTOR SUB-ASSEMBLY

Hide 11302 17.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY