Home › Engine / Hybrid System › 1GD-FTV ENGINE MECHANICAL › FRONT CRANKSHAFT OIL SEAL › 2015.06–2016.08
RM3250E _51 Engine / Hybrid System _037973 1GD-FTV ENGINE MECHANICAL _0184868 FRONT CRANKSHAFT OIL SEAL A

1GD-FTV ENGINE MECHANICAL  FRONT CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 11303A 1.INSTALL FRONT CRANKSHAFT OIL SEAL

a.

Apply MP grease to the lip of a new front crankshaft oil seal.

NOTICE:
·

Keep the lip free of foreign matter.

·

Do not allow MP grease to contact the dust seal.




b.
A343929C01
1.042,2.323 0.625,2.073 0.625,2.073 0.458,2.073 true 0.594,0.302 0.333,0.302 true 1.281,0.771 0.938,0.771 true 0.156,0.188 0.354,0.375 0.198,0.188 10 true *1 1.302,0.667 1.531,0.823 0.229,0.156 10 true *2 0.635,1.104 0.885,1.271 0.25,0.167 10 true *a 0.156,1.979 0.531,2.177 0.375,0.198 10 false SST
*1 Front Crankshaft Oil Seal
*2 Timing Chain Cover Assembly
*a 0 to 1.0 mm (0 to 0.0394 in.)


Using SST and a hammer, tap in the front crankshaft oil seal.

SST
09214-76011  

NOTICE:
·

The acceptable depth from the top of the timing chain cover assembly is 0 to 1.0 mm (0 to 0.0394 in.)

·

Keep the lip free from foreign matter.

·

Do not tap the front crankshaft oil seal at an angle.

·

Make sure that the front crankshaft oil seal is properly installed.




Hide 13471 2.INSTALL CRANKSHAFT PULLEY

a.

Align the keyway of the crankshaft pulley with the key located on the crankshaft, and then slide the crankshaft pulley into place to install it.


b.
A343926N01
1.167,1 0.583,1.333 0.583,1.333 0.417,1.333 true 2.917,0.833 2.75,0.833 2.75,0.833 2.271,1.167 true 0.125,1.24 0.5,1.438 0.375,0.198 10 false SST 2.958,0.729 3.333,0.927 0.375,0.198 10 false SST

Using SST, install a new pulley bolt.

SST
09213-58014  (91551-80840)
09330-00021  

Torque:
365 N*m (3722 kgf*cm, 269 ft.*lbf)


Hide 13496 3.INSTALL CRANKSHAFT PULLEY COVER

a.

w/o Viscous Heater:

Install the crankshaft pulley cover to the crankshaft pulley with the 4 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

w/ Viscous Heater:

Install the crankshaft pulley cover to the crankshaft pulley.


Hide 88451B 4.INSTALL VISCOUS HEATER CRANKSHAFT PULLEY (w/ Viscous Heater)

a.

Install the viscous heater crankshaft pulley to the crankshaft pulley with the 4 bolts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 16400 5.INSTALL RADIATOR ASSEMBLY