Home › Engine / Hybrid System › 1GD-FTV COOLING › RADIATOR
RM3250E _51 Engine / Hybrid System _037977 1GD-FTV COOLING _0193410 RADIATOR A

1GD-FTV COOLING  RADIATOR  INSTALLATION  


PROCEDURE

Hide 16400B 1.INSTALL RADIATOR DRAIN COCK PLUG

a.

Install a new O-ring to the radiator drain cock plug.


b.

Install the radiator drain cock plug to the radiator assembly.


Hide 16546 2.INSTALL RADIATOR PROTECTOR (w/o Air Conditioning System)

a.

Attach the 2 guides and 2 claws to install the radiator protector to the radiator assembly.


Hide 16400 3.INSTALL RADIATOR ASSEMBLY

a.

Temporarily install the radiator assembly to the vehicle.


b.

w/ Air Conditioning System:

Attach the 2 guides and 2 claws to connect the cooler condenser assembly to the radiator assembly.

NOTICE:
·

Do not apply any excessive force to the cooler condenser assembly and cooler pipe.

·

Do not allow the radiator assembly to interfere with other parts.




c.
A341296C01
2.667,1.833 2.833,1.833 2.833,1.833 2.958,1.552 true 2.833,0.25 2.667,0.25 2.667,0.25 2.75,0.5 true 2.5,1.75 2.729,1.948 0.229,0.198 10 true *a 2.875,0.156 3.104,0.354 0.229,0.198 10 true *a
*a Claw


Hook the claw of the radiator assembly as shown in the illustration.


d.
A341291N01
3.031,0.302 3.188,0.5 0.156,0.198 10 true 1 0.938,0.188 1.094,0.385 0.156,0.198 10 true 2 2.594,1.854 2.75,2.052 0.156,0.198 10 true 3 1.615,1.833 1.771,2.031 0.156,0.198 10 true 4

Install the radiator assembly with the 4 bolts in the order shown in the illustration.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


Hide 16572D 4.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the radiator assembly and slide the hose clamp to secure the hose.


Hide 16711 5.INSTALL FAN SHROUD

a.

Install the fan pulley to the engine water pump assembly.


b.

Place the fan shroud together with the fan with fluid coupling assembly between the engine and radiator assembly.

NOTICE:

Do not allow the radiator assembly to interfere with other parts.



c.

Temporarily install the fan with fluid coupling assembly to the engine water pump assembly with the 4 nuts.

NOTICE:
·

Make sure to match the paint mark colors on the fan with fluid coupling assembly with the stud bolts of the same color on the engine water pump assembly.

·

When installing the fan and generator V belt, make sure to securely tighten the nuts of the fan with fluid coupling assembly so that the fan pulley is properly aligned.




d.

Attach the 2 guides and 2 claws to install the fan shroud to the radiator assembly.


e.

Install the fan and generator V belt.

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>DRIVE BELT>INSTALLATION


f.

Tighten the 4 nuts holding the fan with fluid coupling assembly.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


g.

Attach the 2 wire harness clamps.


Hide 32941 6.CONNECT NO. 1 OIL COOLER INLET HOSE (for Automatic Transmission)

a.

Connect the No. 1 oil cooler inlet hose to the radiator assembly and slide the hose clamp to secure the hose.


b.

Attach the clamp to connect the No. 1 oil cooler inlet hose to the fan shroud.


Hide 32942 7.CONNECT NO. 1 OIL COOLER OUTLET HOSE (for Automatic Transmission)

a.

Connect the No. 1 oil cooler outlet tube to the radiator assembly and slide the hose clamp to secure the hose.


Hide 88359 8.INSTALL VISCOUS HEATER V BELT (w/ Viscous Heater)

Hide 16470 9.INSTALL RADIATOR RESERVOIR

a.

Install the radiator reservoir with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Connect the water by-pass hose to the radiator assembly and slide the hose clamp to secure the hose.


c.

Connect the No. 2 water by-pass hose to the radiator assembly and slide the hose clamp to secure the hose.


d.

Attach the clamp to connect the No. 2 water by-pass hose to the fan shroud.


Hide 44369A 10.INSTALL NO. 1 OIL RESERVOIR BRACKET

a.

Temporarily install the No. 1 oil reservoir bracket with the 3 bolts and tighten the 3 bolts.

Torque:
4.5 N*m (46 kgf*cm, 40 in.*lbf)


Hide 44360 11.CONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

a.

Attach the claw to connect the vane pump oil reservoir assembly to the vane pump oil reservoir bracket.


b.

Attach the clamp to connect the pressure feed tube assembly to the fan shroud.


Hide 16571C 12.INSTALL NO. 1 RADIATOR HOSE

a.

Install the No. 1 radiator hose and slide the 2 hose clamps to secure the hose.


Hide 17362B 13.INSTALL NO. 2 AIR TUBE

a.

Install the No. 2 air tube with the 2 bolts and tighten the hose clamp to secure the tube.

Torque:
for bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
for hose clamp : 6.5 N*m (66 kgf*cm, 58 in.*lbf)


b.

Attach the 4 clamps to connect the oil return hose to the No. 2 air tube.


Hide 17344E 14.INSTALL NO. 4 AIR HOSE

a.

Install the No. 4 air hose and tighten the 2 hose clamps to secure the hose.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


b.

Attach the 2 clamps to connect the oil return hose to the No. 4 air hose.


Hide 16593 17.INSTALL NO. 1 RADIATOR AIR GUIDE

a.

Install the No. 1 radiator air guide with 4 new clips.


Hide 51410 18.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY (for 4WD and Pre-Runner)

Hide 12601B 20.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY