Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Entry and Start System) › 2015.06–2016.01
RM3250E _58 Vehicle Interior _038065 THEFT DETERRENT / KEYLESS ENTRY _0184915 IMMOBILISER SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Entry and Start System)  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

When there is a communication malfunction between the ECM and certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU)*, or when the communication ID codes do not match, the ECM stores this DTC.

*: w/ Seat Heater System


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2799 Engine Immobiliser System Malfunction Either condition is met (1 trip detection logic*1):
·

A malfunction in the communication or communication lines between the ECM and certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU)*4.

·

A matching communication code cannot be verified during communication between the ECM and certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU)*4.


·

Certification ECU (smart key ECU assembly)

·

ECM

·

ID code box (immobiliser code ECU)*4

·

Harness or connector


DTC output confirmation operation (Either condition is met):
·

Within 10 seconds of an engine start operation being performed (with the shift lever in P*2 and the brake pedal*2 or clutch pedal*3 depressed, the engine switch is pressed while the key is being carried). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).

·

10 seconds after the engine switch is turned on (IG) after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the engine switch being turned on (IG), and DTCs are stored after 6 seconds).



*1: Only output while a malfunction is present.

*2: for Automatic Transmission

*3: for Manual Transmission

*4: w/ Seat Heater System


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2799 -

WIRING DIAGRAM

w/o Seat Heater System
B413956E01
4.948,2.854 6.75,3.385 1.802,0.531 10 false Certification ECU (Smart Key ECU Assembly) 4.646,1.917 6.448,2.448 1.802,0.531 10 false G70 4.646,1.01 6.448,1.542 1.802,0.531 10 false G69 4.708,0.781 6.51,1.313 1.802,0.531 10 false 3 4.698,1.688 6.5,2.219 1.802,0.531 10 false 35 5.042,1.771 6.854,1.99 1.813,0.219 10 false EFIO 5.042,0.885 6.854,1.104 1.813,0.219 10 false EFII 6,0.229 6.615,0.448 0.615,0.219 10 false +B 1.75,1.469 2.365,1.688 0.615,0.219 10 false +B 1.979,1.792 2.594,2.01 0.615,0.219 10 false IMI 1.99,0.865 2.604,1.083 0.615,0.219 10 false IMO 1.271,2.875 1.885,3.094 0.615,0.219 10 false ECM 2.344,1.01 2.958,1.229 0.615,0.219 10 false G45 2.365,1.917 2.979,2.135 0.615,0.219 10 false G45 2.75,1.01 3.365,1.229 0.615,0.219 10 false G83 2.74,1.917 3.354,2.135 0.615,0.219 10 false G83 3.146,1.917 3.76,2.135 0.615,0.219 10 false G86 3.146,1 3.76,1.219 0.615,0.219 10 false G86 3.542,1 4.156,1.219 0.615,0.219 10 false G88 3.552,1.906 4.167,2.125 0.615,0.219 10 false G88 2.417,2.146 3.031,2.365 0.615,0.219 10 false *1 2.823,2.156 3.417,2.365 0.594,0.208 10 false *2 3.219,2.156 3.813,2.365 0.594,0.208 10 false *3 3.635,2.167 4.229,2.375 0.594,0.208 10 false *4 2.406,1.229 3.021,1.448 0.615,0.219 10 false *1 2.823,1.229 3.417,1.438 0.594,0.208 10 false *2 3.24,1.229 3.833,1.438 0.594,0.208 10 false *3 3.635,1.229 4.229,1.438 0.594,0.208 10 false *4 2.406,1.667 3.021,1.885 0.615,0.219 10 false 10 2.802,1.667 3.417,1.885 0.615,0.219 10 false 30 3.208,1.677 3.823,1.896 0.615,0.219 10 false 16 3.604,1.677 4.219,1.896 0.615,0.219 10 false 10 2.427,0.771 3.042,0.99 0.615,0.219 10 false 9 2.813,0.76 3.427,0.979 0.615,0.219 10 false 29 3.219,0.76 3.833,0.979 0.615,0.219 10 false 17 3.625,0.76 4.24,0.979 0.615,0.219 10 false 8 2.844,2.604 4.844,2.823 2,0.219 10 false *1: for 2TR-FE 2.844,2.896 4.844,3.115 2,0.219 10 false *2: for 1KD-FTV, 2KD-FTV 2.865,3.188 4.865,3.406 2,0.219 10 false *3: for 1GD-FTV, 2GD-FTV 2.854,3.479 4.854,3.698 2,0.219 10 false *4: for 1GR-FE

w/ Seat Heater System
B413957E01
5.021,3.094 6.583,3.469 1.563,0.375 10 false ID Code Box (Immobiliser Code ECU) 5.01,2.938 6.573,3.313 1.563,0.375 10 false G82 4.813,0.99 6.375,1.365 1.563,0.375 10 false 3 4.823,1.875 6.385,2.25 1.563,0.375 10 false 4 5.042,0.99 6.604,1.365 1.563,0.375 10 false EFII 5.052,1.865 6.615,2.24 1.563,0.375 10 false EFIO 5.99,0.323 7.063,0.729 1.073,0.406 10 false +B 1.75,1.573 2.823,1.979 1.073,0.406 10 false +B 1.958,0.99 3.031,1.396 1.073,0.406 10 false IMO 1.979,1.906 3.052,2.313 1.073,0.406 10 false IMI 2.354,0.99 3.427,1.396 1.073,0.406 10 false 17 2.354,1.906 3.427,2.313 1.073,0.406 10 false 16 1.146,2.938 2.219,3.344 1.073,0.406 10 false G86 1.156,3.083 2.229,3.49 1.073,0.406 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU)* or ECM, refer to Service Bulletin.

*: w/ Seat Heater System

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



HINT:

When DTC B2799 and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC

Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Start the engine.


b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

B2799 is not output.



Result:
Result Proceed to
OK A
NG (DTC B2799 is output) (w/ Seat Heater System) B
NG (DTC B2799 is output) (w/o Seat Heater System) C
NG (Other DTCs are output) D



A

END (REGISTERED COMMUNICATION ID WAS DEFECTIVE)

B

4.INSPECT ECM (TERMINAL IMO)

C

15.INSPECT ECM (TERMINAL IMO)

D

4.INSPECT ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

E317803C02
0.521,0.625 0.958,0.844 0.438,0.219 1.667,0.625 2.104,0.844 0.438,0.219 2.802,0.615 3.24,0.833 0.438,0.219 3.854,0.615 4.292,0.833 0.438,0.219 4.969,0.615 5.406,0.833 0.438,0.219 6.104,0.604 6.542,0.823 0.438,0.219 5.771,2.073 5.917,1.438 true 0.604,0.677 0.938,0.865 0.333,0.188 10 false C57 1.76,0.677 2.094,0.865 0.333,0.188 10 false C58 2.896,0.667 3.229,0.854 0.333,0.188 10 false C59 3.938,0.656 4.271,0.844 0.333,0.188 10 false C60 5.052,0.646 5.385,0.833 0.333,0.188 10 false G85 6.198,0.635 6.531,0.823 0.333,0.188 10 false G86 2.938,4.104 3.271,4.292 0.333,0.188 10 false *b 0.26,0.104 0.594,0.292 0.333,0.188 10 false *a 5.625,2.146 5.958,2.333 0.333,0.188 10 false IMO 0.927,4.052 1.427,4.25 0.5,0.198 10 false GND
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition
Item Content
Tester Connection G86-17 (IMO) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected

OK:

The waveform is similar to that shown in the illustration.



Result:
Result Proceed to
Normal waveform A
Terminal IMO stuck low (2.4 V or less) B
Terminal IMO stuck high (12 V) or abnormal waveform C



A

5.INSPECT ECM (TERMINAL IMI)

B

11.INSPECT ECM (IMO TERMINAL VOLTAGE)

C

8.REPLACE ECM
5.INSPECT ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

E317804C02
0.594,0.448 1.063,0.677 0.469,0.229 1.667,0.448 2.135,0.677 0.469,0.229 2.813,0.448 3.281,0.677 0.469,0.229 3.885,0.448 4.354,0.677 0.469,0.229 5.063,0.448 5.531,0.677 0.469,0.229 6.146,0.448 6.615,0.677 0.469,0.229 5.708,1.99 6.042,1.302 true 0.167,0.094 0.479,0.25 0.313,0.156 10 false *a 3.354,4.125 3.667,4.281 0.313,0.156 10 false *b 0.948,4.052 1.417,4.208 0.469,0.156 10 false GND 0.698,0.49 1.031,0.656 0.333,0.167 10 false C57 1.781,0.5 2.115,0.667 0.333,0.167 10 false C58 2.958,0.5 3.292,0.667 0.333,0.167 10 false C59 4,0.5 4.333,0.667 0.333,0.167 10 false C60 5.156,0.5 5.49,0.667 0.333,0.167 10 false G85 6.25,0.5 6.583,0.667 0.333,0.167 10 false G86 5.583,2.031 5.917,2.198 0.333,0.167 10 false IMI
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition
Item Content
Tester Connection G86-16 (IMI) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected

OK:

The waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

6.REGISTER ECU COMMUNICATION ID

NG

13.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
6.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER ENGINE STARTS
7.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).


b.

Check that the engine starts 5 seconds after the engine switch turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

8.REPLACE ECM
8.REPLACE ECM
a.

Temporarily replace the ECM with a new one.



Result:
Proceed to
NEXT



NEXT

9.REGISTER ECU COMMUNICATION ID
9.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER ENGINE STARTS
10.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).


b.

Check that the engine starts 5 seconds after the engine switch turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ECM WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

11.INSPECT ECM (IMO TERMINAL VOLTAGE)
a.

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.
E317805C02
1.521,0.385 1.948,0.656 0.427,0.271 2.938,2.167 2.615,1.719 true 0.115,0.198 0.427,0.354 0.313,0.156 10 false *a 1.604,0.448 2.073,0.656 0.469,0.208 10 false G86 2.844,2.208 3.313,2.417 0.469,0.208 10 false IMO
*a Front view of wire harness connector
(to ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Result
G86-17 (IMO) - Body ground Engine switch on (IG) using registered key Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform



Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B



A

12.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

B

8.REPLACE ECM
12.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
a.

Disconnect the G82 ID code box (immobiliser code ECU) connector.


b.

Disconnect the G86 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-3 (EFII) - G86-17 (IMO) Always Below 1 Ω
G82-4 (EFIO) - G86-16 (IMI) Always Below 1 Ω
G86-17 (IMO) - Body ground Always 10 kΩ or higher
G82-3 (EFII) - Body ground Always 10 kΩ or higher
G86-16 (IMI) - Body ground Always 10 kΩ or higher
G82-4 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.

HINT:

Refer to Service Bulletin.


NOTICE:

Recognition code registration is necessary when replacing the ID code box (immobiliser code ECU).

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

14.CHECK WHETHER ENGINE STARTS
14.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).


b.

Check that the engine starts 5 seconds after the engine switch was turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG (for 1GD-FTV)
NG (for 2GD-FTV)



OK

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

NG (for 1GD-FTV)

NG (for 2GD-FTV)

15.INSPECT ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

B413958C01
0.865,0.073 1.281,0.292 0.417,0.219 2.115,0.073 2.531,0.292 0.417,0.219 3.396,0.073 3.813,0.292 0.417,0.219 4.656,0.083 5.073,0.302 0.417,0.219 5.833,0.063 6.25,0.281 0.417,0.219 5.49,1.354 5.906,1.573 0.417,0.219 1.281,1.354 1.698,1.573 0.417,0.219 2.635,1.354 3.052,1.573 0.417,0.219 4.198,1.354 4.615,1.573 0.417,0.219 1.438,2.74 1.854,2.958 0.417,0.219 2.74,2.729 3.156,2.948 0.417,0.219 4.135,2.74 4.552,2.958 0.417,0.219 5.302,2.74 5.719,2.958 0.417,0.219 0.729,4.146 1.146,4.365 0.417,0.219 1.781,4.146 2.198,4.365 0.417,0.219 2.875,4.156 3.292,4.375 0.417,0.219 3.896,4.146 4.313,4.365 0.417,0.219 4.927,4.146 5.344,4.365 0.417,0.219 5.938,4.135 6.354,4.354 0.417,0.219 1.354,5.375 1.771,5.594 0.417,0.219 2.104,5.375 2.521,5.594 0.417,0.219 3.073,5.375 3.49,5.594 0.417,0.219 3.844,5.375 4.26,5.594 0.417,0.219 4.604,5.385 5.021,5.604 0.417,0.219 5.344,5.385 5.76,5.604 0.417,0.219 2.469,6.042 2.594,6.781 2.594,6.781 2.74,6.781 true 5.813,4.823 5.938,5.563 5.938,5.563 6.083,5.563 true 4.688,3.833 4.76,4.104 4.76,4.104 4.625,4.104 true 4.594,2.135 4.708,2.75 4.708,2.75 4.854,2.75 true 5.042,0.802 5.313,0.24 5.313,0.24 5.458,0.24 true 0.958,0.104 1.417,0.302 0.458,0.198 10 false C52 2.188,0.104 2.646,0.302 0.458,0.198 10 false C53 3.469,0.104 3.927,0.302 0.458,0.198 10 false C54 4.74,0.115 5.198,0.313 0.458,0.198 10 false G45 5.917,0.104 6.375,0.302 0.458,0.198 10 false G46 1.365,1.375 1.823,1.573 0.458,0.198 10 false C52 2.719,1.385 3.177,1.583 0.458,0.198 10 false C53 4.281,1.375 4.74,1.573 0.458,0.198 10 false G45 5.563,1.385 6.021,1.583 0.458,0.198 10 false G46 0.052,0.052 0.51,0.25 0.458,0.198 12 false *A 0.042,1.385 0.5,1.583 0.458,0.198 12 false *B 0.063,2.729 0.521,2.927 0.458,0.198 12 false *C 0.073,4.125 0.531,4.323 0.458,0.198 12 false *D 0.104,5.406 0.563,5.604 0.458,0.198 12 false *E 0.073,0.229 0.531,0.427 0.458,0.198 10 false *a 0.073,1.573 0.531,1.771 0.458,0.198 10 false *a 0.083,2.906 0.542,3.104 0.458,0.198 10 false *a 0.094,4.323 0.552,4.521 0.458,0.198 10 false *a 0.135,5.583 0.594,5.781 0.458,0.198 10 false *a 2.938,8.354 3.396,8.552 0.458,0.198 10 false *b 0.99,8.271 1.448,8.469 0.458,0.198 10 false GND 1.521,2.771 1.979,2.969 0.458,0.198 10 false C55 2.823,2.76 3.281,2.958 0.458,0.198 10 false C56 4.208,2.771 4.667,2.969 0.458,0.198 10 false G83 5.385,2.771 5.844,2.969 0.458,0.198 10 false G84 0.813,4.188 1.271,4.385 0.458,0.198 10 false C57 1.875,4.188 2.333,4.385 0.458,0.198 10 false C58 2.969,4.198 3.427,4.396 0.458,0.198 10 false C59 3.979,4.177 4.438,4.375 0.458,0.198 10 false C60 5.01,4.177 5.469,4.375 0.458,0.198 10 false G85 6.021,4.167 6.479,4.365 0.458,0.198 10 false G86 1.438,5.417 1.896,5.615 0.458,0.198 10 false G87 2.177,5.417 2.635,5.615 0.458,0.198 10 false G88 3.156,5.427 3.615,5.625 0.458,0.198 10 false C15 3.938,5.427 4.396,5.625 0.458,0.198 10 false C14 4.677,5.427 5.135,5.625 0.458,0.198 10 false C13 5.427,5.427 5.885,5.625 0.458,0.198 10 false C12 2.781,6.708 3.24,6.906 0.458,0.198 10 false IMO 6.125,5.479 6.583,5.677 0.458,0.198 10 false IMO 4.354,4.031 4.813,4.229 0.458,0.198 10 false IMO 4.906,2.677 5.365,2.875 0.458,0.198 10 false IMO 5.5,0.156 5.958,0.354 0.458,0.198 10 false IMO
*A for 2TR-FE (for Automatic Transmission) *B for 2TR-FE (for Manual Transmission)
*C for 1KD-FTV, 2KD-FTV *D for 1GD-FTV, 2GD-FTV
*E for 1GR-FE - -
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition
Item Content
Tester Connection G45-9 (IMO) - Body ground*1
G83-29 (IMO) - Body ground*2
G86-17 (IMO) - Body ground*3
G88-8 (IMO) - Body ground*4
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected

*1: for 2TR-FE

*2: for 1KD-FTV, 2KD-FTV

*3: for 1GD-FTV, 2GD-FTV

*4: for 1GR-FE


OK:

The waveform is similar to that shown in the illustration.



Result:
Result Proceed to
Normal waveform A
Terminal IMO stuck low (2.4 V or less) B
Terminal IMO stuck high (12 V) or abnormal waveform C



A

16.INSPECT ECM (TERMINAL IMI)

B

22.INSPECT ECM (IMO TERMINAL VOLTAGE)

C

19.REPLACE ECM
16.INSPECT ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

B413959C01
0.771,4.219 1.156,4.427 0.385,0.208 1.823,4.219 2.208,4.427 0.385,0.208 2.948,4.208 3.333,4.417 0.385,0.208 3.906,4.219 4.292,4.427 0.385,0.208 4.969,4.208 5.354,4.417 0.385,0.208 5.99,4.208 6.375,4.417 0.385,0.208 1.385,5.417 1.771,5.625 0.385,0.208 3.125,5.417 3.51,5.625 0.385,0.208 3.906,5.417 4.292,5.625 0.385,0.208 2.094,5.406 2.479,5.615 0.385,0.208 4.615,5.417 5,5.625 0.385,0.208 5.375,5.417 5.76,5.625 0.385,0.208 1.458,2.823 1.844,3.031 0.385,0.208 2.74,2.813 3.125,3.021 0.385,0.208 4.156,2.813 4.542,3.021 0.385,0.208 5.292,2.823 5.677,3.031 0.385,0.208 1.333,1.375 1.719,1.583 0.385,0.208 2.677,1.365 3.063,1.573 0.385,0.208 4.219,1.375 4.604,1.583 0.385,0.208 5.49,1.365 5.875,1.573 0.385,0.208 5.823,0.083 6.208,0.292 0.385,0.208 4.656,0.083 5.042,0.292 0.385,0.208 3.385,0.094 3.771,0.302 0.385,0.208 2.156,0.083 2.542,0.292 0.385,0.208 0.865,0.094 1.25,0.302 0.385,0.208 4.958,0.792 5.188,0.208 5.188,0.208 5.344,0.208 true 4.521,2.083 4.75,1.5 4.75,1.5 4.906,1.5 true 4.563,3.833 4.396,4.146 4.396,4.146 4.552,4.146 true 5.906,4.813 6.135,5.375 6.135,5.375 6.292,5.375 true 2.229,6.01 2.333,6.802 2.333,6.802 2.49,6.802 true 0.938,0.125 1.396,0.323 0.458,0.198 10 false C52 3.448,0.135 3.906,0.333 0.458,0.198 10 false C54 4.729,0.115 5.188,0.313 0.458,0.198 10 false G45 5.875,0.104 6.333,0.302 0.458,0.198 10 false G46 2.229,0.115 2.688,0.313 0.458,0.198 10 false C53 3.198,5.448 3.656,5.646 0.458,0.198 10 false C15 2.729,1.396 3.188,1.594 0.458,0.198 10 false C53 4.208,2.844 4.667,3.042 0.458,0.198 10 false G83 5.563,1.396 6.021,1.594 0.458,0.198 10 false G46 1.552,2.854 2.01,3.052 0.458,0.198 10 false C55 2.813,2.844 3.271,3.042 0.458,0.198 10 false C56 4.281,1.396 4.74,1.594 0.458,0.198 10 false G45 5.365,2.854 5.823,3.052 0.458,0.198 10 false G84 0.833,4.25 1.292,4.448 0.458,0.198 10 false C57 1.906,4.25 2.365,4.448 0.458,0.198 10 false C58 2.979,4.25 3.438,4.448 0.458,0.198 10 false C59 3.979,4.25 4.438,4.448 0.458,0.198 10 false C60 5.042,4.25 5.5,4.448 0.458,0.198 10 false G85 6.042,4.25 6.5,4.448 0.458,0.198 10 false G86 1.438,5.448 1.896,5.646 0.458,0.198 10 false G87 2.177,5.448 2.635,5.646 0.458,0.198 10 false G88 3.958,5.448 4.417,5.646 0.458,0.198 10 false C14 4.688,5.448 5.146,5.646 0.458,0.198 10 false C13 5.448,5.448 5.906,5.646 0.458,0.198 10 false C12 1.417,1.406 1.875,1.604 0.458,0.198 10 false C52 0.063,0.063 0.521,0.26 0.458,0.198 12 false *A 0.073,1.385 0.531,1.583 0.458,0.198 12 false *B 0.083,2.792 0.542,2.99 0.458,0.198 12 false *C 0.083,4.208 0.542,4.406 0.458,0.198 12 false *D 0.104,5.406 0.563,5.604 0.458,0.198 12 false *E 0.073,0.24 0.531,0.438 0.458,0.198 10 false *a 0.094,1.594 0.552,1.792 0.458,0.198 10 false *a 0.104,2.979 0.563,3.177 0.458,0.198 10 false *a 0.104,4.385 0.563,4.583 0.458,0.198 10 false *a 0.125,5.583 0.583,5.781 0.458,0.198 10 false *a 0.969,8.26 1.427,8.458 0.458,0.198 10 false GND 3.323,8.344 3.781,8.542 0.458,0.198 10 false *b 5.396,0.135 5.854,0.333 0.458,0.198 10 false IMI 4.969,1.417 5.427,1.615 0.458,0.198 10 false IMI 4.625,4.083 5.083,4.281 0.458,0.198 10 false IMI 6.344,5.292 6.802,5.49 0.458,0.198 10 false IMI 2.531,6.708 2.99,6.906 0.458,0.198 10 false IMI
*A for 2TR-FE (for Automatic Transmission) *B for 2TR-FE (for Manual Transmission)
*C for 1KD-FTV, 2KD-FTV *D for 1GD-FTV, 2GD-FTV
*E for 1GR-FE - -
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition
Item Content
Tester Connection G45-10 (IMI) - Body ground*1
G83-30 (IMI) - Body ground*2
G86-16 (IMI) - Body ground*3
G88-10 (IMI) - Body ground*4
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected

*1: for 2TR-FE

*2: for 1KD-FTV, 2KD-FTV

*3: for 1GD-FTV, 2GD-FTV

*4: for 1GR-FE


OK:

The waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

17.REGISTER ECU COMMUNICATION ID

NG

24.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
17.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

18.CHECK WHETHER ENGINE STARTS
18.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).


b.

Check that the engine starts 5 seconds after the engine switch turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

19.REPLACE ECM
19.REPLACE ECM

NEXT

20.REGISTER ECU COMMUNICATION ID
20.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

21.CHECK WHETHER ENGINE STARTS
21.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).


b.

Check that the engine starts 5 seconds after the engine switch turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ECM WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

22.INSPECT ECM (IMO TERMINAL VOLTAGE)
a.

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

B413960C01
0.844,0.396 1.24,0.656 0.396,0.26 2.615,0.396 3.01,0.656 0.396,0.26 4.458,0.406 4.854,0.667 0.396,0.26 6.063,0.24 6.458,0.5 0.396,0.26 0.792,1.406 1.073,2.24 1.073,2.24 1.229,2.24 true 2.385,1.719 2.552,2.229 2.552,2.229 2.708,2.229 true 5.24,1.427 5.042,2.198 5.042,2.198 4.875,2.198 true 6.125,1.323 5.917,2.177 5.917,2.177 5.75,2.177 true 0.094,0.208 0.406,0.406 0.313,0.198 10 false *a 0.104,0.042 0.417,0.24 0.313,0.198 12 false *A 1.906,0.031 2.219,0.229 0.313,0.198 12 false *B 3.719,0.042 4.031,0.24 0.313,0.198 12 false *C 5.521,0.052 5.833,0.25 0.313,0.198 12 false *D 1.927,0.198 2.24,0.396 0.313,0.198 10 false *a 3.75,0.208 4.063,0.406 0.313,0.198 10 false *a 5.542,0.219 5.854,0.417 0.313,0.198 10 false *a 1.271,2.167 1.729,2.365 0.458,0.198 10 false IMO 2.76,2.156 3.219,2.354 0.458,0.198 10 false IMO 4.594,2.125 5.052,2.323 0.458,0.198 10 false IMO 5.479,2.104 5.938,2.302 0.458,0.198 10 false IMO 0.917,0.438 1.375,0.635 0.458,0.198 10 false G45 2.698,0.448 3.156,0.646 0.458,0.198 10 false G83 4.531,0.458 4.99,0.656 0.458,0.198 10 false G86 6.135,0.292 6.594,0.49 0.458,0.198 10 false G88
*A for 2TR-FE *B for 1KD-FTV, 2KD-FTV
*C for 1GD-FTV, 2GD-FTV *D for 1GR-FE
*a Front view of wire harness connector
(to ECM)
- -


Standard Voltage:
Tester Connection Condition Result
G45-9 (IMO) - Body ground*1
G83-29 (IMO) - Body ground*2
G86-17 (IMO) - Body ground*3
G88-8 (IMO) - Body ground*4
Engine switch on (IG) using registered key Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform


*1: for 2TR-FE

*2: for 1KD-FTV, 2KD-FTV

*3: for 1GD-FTV, 2GD-FTV

*4: for 1GR-FE



Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B



A

23.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

B

19.REPLACE ECM
23.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Disconnect the G69 and G70 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the G45*1, G83*2, G86*3 or G88*4 ECM connector.

*1: for 2TR-FE

*2: for 1KD-FTV, 2KD-FTV

*3: for 1GD-FTV, 2GD-FTV

*4: for 1GR-FE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2TR-FE
Tester Connection Condition Specified Condition
G69-3 (EFII) - G45-9 (IMO) Always Below 1 Ω
G70-35 (EFIO) - G45-10 (IMI) Always Below 1 Ω
G45-9 (IMO) - Body ground Always 10 kΩ or higher
G69-3 (EFII) - Body ground Always 10 kΩ or higher
G45-10 (IMI) - Body ground Always 10 kΩ or higher
G70-35 (EFIO) - Body ground Always 10 kΩ or higher

for 1KD-FTV, 2KD-FTV
Tester Connection Condition Specified Condition
G69-3 (EFII) - G83-29 (IMO) Always Below 1 Ω
G70-35 (EFIO) - G83-30 (IMI) Always Below 1 Ω
G83-29 (IMO) - Body ground Always 10 kΩ or higher
G69-3 (EFII) - Body ground Always 10 kΩ or higher
G83-30 (IMI) - Body ground Always 10 kΩ or higher
G70-35 (EFIO) - Body ground Always 10 kΩ or higher

for 1GD-FTV, 2GD-FTV
Tester Connection Condition Specified Condition
G69-3 (EFII) - G86-17 (IMO) Always Below 1 Ω
G70-35 (EFIO) - G86-16 (IMI) Always Below 1 Ω
G86-17 (IMO) - Body ground Always 10 kΩ or higher
G69-3 (EFII) - Body ground Always 10 kΩ or higher
G86-16 (IMI) - Body ground Always 10 kΩ or higher
G70-35 (EFIO) - Body ground Always 10 kΩ or higher

for 1GR-FE
Tester Connection Condition Specified Condition
G69-3 (EFII) - G88-8 (IMO) Always Below 1 Ω
G70-35 (EFIO) - G88-10 (IMI) Always Below 1 Ω
G88-8 (IMO) - Body ground Always 10 kΩ or higher
G69-3 (EFII) - Body ground Always 10 kΩ or higher
G88-10 (IMI) - Body ground Always 10 kΩ or higher
G70-35 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

24.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.


NOTICE:

Recognition code registration is necessary when replacing the certification ECU (smart key ECU assembly).

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

25.CHECK WHETHER ENGINE STARTS
25.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).


b.

Check that the engine starts 5 seconds after the engine switch was turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG (for 2TR-FE)
NG (for 1KD-FTV)
NG (for 2KD-FTV)
NG (for 1GD-FTV)
NG (for 2GD-FTV)
NG (for 1GR-FE)



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG (for 2TR-FE)

NG (for 1KD-FTV)

NG (for 2KD-FTV)

NG (for 1GD-FTV)

NG (for 2GD-FTV)

NG (for 1GR-FE)