Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Entry and Start System) › 2015.06–2016.01
RM3250E _58 Vehicle Interior _038065 THEFT DETERRENT / KEYLESS ENTRY _0184916 IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Entry and Start System)  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

The ECM stores this DTC when a communication line between the ECM and transponder key ECU assembly is malfunctioning or the communication ID of the ECM and transponder key ECU assembly do not match.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2799 Engine Immobiliser System Malfunction One of the following conditions is met:
·

Error in communication between ECM and transponder key ECU assembly.

·

Error in communication lines.

·

Communication ID is different during communication between ECM and transponder key ECU assembly.


·

Harness or connector

·

Transponder key ECU assembly

·

ECM


DTC Output Confirmation Operation:
·

Start the engine and wait 10 seconds.

·

After disconnecting and reconnecting the cable to the negative (-) battery terminal, turn the ignition switch to ON and wait 10 seconds.



Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2799 -

WIRING DIAGRAM

B413975E01
4.865,2.833 7.156,3.25 2.292,0.417 10 false G16 4.865,3.031 7.156,3.448 2.292,0.417 10 false Transponder Key ECU Assembly 4.781,0.906 7.156,1.323 2.375,0.417 10 false 12 4.781,1.802 7.156,2.219 2.375,0.417 10 false 13 5.031,0.906 7.156,1.344 2.125,0.438 10 false EFII 5.031,1.802 7.156,2.24 2.125,0.438 10 false EFIO 1.969,0.917 4.094,1.354 2.125,0.438 10 false IMO 2.01,1.823 4.135,2.26 2.125,0.438 10 false IMI 6.021,0.229 6.865,0.625 0.844,0.396 10 false +B 1.75,1.469 2.594,1.865 0.844,0.396 10 false +B 2.354,1.01 4.479,1.448 2.125,0.438 10 false G45 2.375,1.917 4.5,2.354 2.125,0.438 10 false G45 2.75,1.01 4.875,1.448 2.125,0.438 10 false G83 2.75,1.927 4.875,2.365 2.125,0.438 10 false G83 3.146,1.01 5.271,1.448 2.125,0.438 10 false G86 3.146,1.917 5.271,2.354 2.125,0.438 10 false G86 3.542,1.01 5.667,1.448 2.125,0.438 10 false G88 3.552,1.917 5.677,2.354 2.125,0.438 10 false G88 2.427,0.781 4.552,1.219 2.125,0.438 10 false 9 2.406,1.688 4.531,2.125 2.125,0.438 10 false 10 2.802,0.771 4.927,1.208 2.125,0.438 10 false 29 2.802,1.698 4.927,2.135 2.125,0.438 10 false 30 3.208,1.688 5.333,2.125 2.125,0.438 10 false 16 3.594,1.688 5.719,2.125 2.125,0.438 10 false 10 3.635,0.792 5.76,1.229 2.125,0.438 10 false 8 3.198,0.771 5.323,1.208 2.125,0.438 10 false 17 2.427,1.25 4.552,1.688 2.125,0.438 10 false *1 2.448,2.156 4.573,2.594 2.125,0.438 10 false *1 2.813,2.156 4.938,2.594 2.125,0.438 10 false *2 3.229,2.167 5.354,2.604 2.125,0.438 10 false *3 3.625,2.167 5.75,2.604 2.125,0.438 10 false *4 2.813,1.25 4.938,1.688 2.125,0.438 10 false *2 3.229,1.25 5.354,1.688 2.125,0.438 10 false *3 3.615,1.25 5.74,1.688 2.125,0.438 10 false *4 1.396,2.844 3.521,3.281 2.125,0.438 10 false ECM 2.688,2.583 4.813,3.021 2.125,0.438 10 false *1: for 1TR-FE, 2TR-FE 2.698,2.854 4.823,3.292 2.125,0.438 10 false *2: for 1KD-FTV, 2KD-FTV 2.708,3.125 4.833,3.563 2.125,0.438 10 false *3: for 1GD-FTV, 2GD-FTV 2.719,3.458 4.802,3.802 2.083,0.344 10 false *4: for 1GR-FE

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

If transponder key ECU assembly DTCs are output simultaneously, troubleshoot the transponder key ECU assembly DTCs first.


PROCEDURE

1.CLEAR DTC

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Start the engine.


b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

B2799 is not output.



Result:
Result Proceed to
OK A
NG (B2799 is output) B
NG (Other DTCs are output) C



A

B

3.INSPECT ECM (TERMINAL IMO)

C

3.INSPECT ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

B413958C01
0.865,0.073 1.281,0.292 0.417,0.219 2.115,0.073 2.531,0.292 0.417,0.219 3.396,0.073 3.813,0.292 0.417,0.219 4.656,0.083 5.073,0.302 0.417,0.219 5.833,0.063 6.25,0.281 0.417,0.219 5.49,1.354 5.906,1.573 0.417,0.219 1.281,1.354 1.698,1.573 0.417,0.219 2.635,1.354 3.052,1.573 0.417,0.219 4.198,1.354 4.615,1.573 0.417,0.219 1.438,2.74 1.854,2.958 0.417,0.219 2.74,2.729 3.156,2.948 0.417,0.219 4.135,2.74 4.552,2.958 0.417,0.219 5.302,2.74 5.719,2.958 0.417,0.219 0.729,4.146 1.146,4.365 0.417,0.219 1.781,4.146 2.198,4.365 0.417,0.219 2.875,4.156 3.292,4.375 0.417,0.219 3.896,4.146 4.313,4.365 0.417,0.219 4.927,4.146 5.344,4.365 0.417,0.219 5.938,4.135 6.354,4.354 0.417,0.219 1.354,5.375 1.771,5.594 0.417,0.219 2.104,5.375 2.521,5.594 0.417,0.219 3.073,5.375 3.49,5.594 0.417,0.219 3.844,5.375 4.26,5.594 0.417,0.219 4.604,5.385 5.021,5.604 0.417,0.219 5.344,5.385 5.76,5.604 0.417,0.219 2.469,6.042 2.594,6.781 2.594,6.781 2.74,6.781 true 5.813,4.823 5.938,5.563 5.938,5.563 6.083,5.563 true 4.688,3.833 4.76,4.104 4.76,4.104 4.625,4.104 true 4.594,2.135 4.708,2.75 4.708,2.75 4.854,2.75 true 5.042,0.802 5.313,0.24 5.313,0.24 5.458,0.24 true 0.958,0.104 1.417,0.302 0.458,0.198 10 false C52 2.188,0.104 2.646,0.302 0.458,0.198 10 false C53 3.469,0.104 3.927,0.302 0.458,0.198 10 false C54 4.74,0.115 5.198,0.313 0.458,0.198 10 false G45 5.917,0.104 6.375,0.302 0.458,0.198 10 false G46 1.365,1.375 1.823,1.573 0.458,0.198 10 false C52 2.719,1.385 3.177,1.583 0.458,0.198 10 false C53 4.281,1.375 4.74,1.573 0.458,0.198 10 false G45 5.563,1.385 6.021,1.583 0.458,0.198 10 false G46 0.052,0.052 0.51,0.25 0.458,0.198 12 false *A 0.042,1.385 0.5,1.583 0.458,0.198 12 false *B 0.063,2.729 0.521,2.927 0.458,0.198 12 false *C 0.073,4.125 0.531,4.323 0.458,0.198 12 false *D 0.104,5.406 0.563,5.604 0.458,0.198 12 false *E 0.073,0.229 0.531,0.427 0.458,0.198 10 false *a 0.073,1.573 0.531,1.771 0.458,0.198 10 false *a 0.083,2.906 0.542,3.104 0.458,0.198 10 false *a 0.094,4.323 0.552,4.521 0.458,0.198 10 false *a 0.135,5.583 0.594,5.781 0.458,0.198 10 false *a 2.938,8.354 3.396,8.552 0.458,0.198 10 false *b 0.99,8.271 1.448,8.469 0.458,0.198 10 false GND 1.521,2.771 1.979,2.969 0.458,0.198 10 false C55 2.823,2.76 3.281,2.958 0.458,0.198 10 false C56 4.208,2.771 4.667,2.969 0.458,0.198 10 false G83 5.385,2.771 5.844,2.969 0.458,0.198 10 false G84 0.813,4.188 1.271,4.385 0.458,0.198 10 false C57 1.875,4.188 2.333,4.385 0.458,0.198 10 false C58 2.969,4.198 3.427,4.396 0.458,0.198 10 false C59 3.979,4.177 4.438,4.375 0.458,0.198 10 false C60 5.01,4.177 5.469,4.375 0.458,0.198 10 false G85 6.021,4.167 6.479,4.365 0.458,0.198 10 false G86 1.438,5.417 1.896,5.615 0.458,0.198 10 false G87 2.177,5.417 2.635,5.615 0.458,0.198 10 false G88 3.156,5.427 3.615,5.625 0.458,0.198 10 false C15 3.938,5.427 4.396,5.625 0.458,0.198 10 false C14 4.677,5.427 5.135,5.625 0.458,0.198 10 false C13 5.427,5.427 5.885,5.625 0.458,0.198 10 false C12 2.781,6.708 3.24,6.906 0.458,0.198 10 false IMO 6.125,5.479 6.583,5.677 0.458,0.198 10 false IMO 4.354,4.031 4.813,4.229 0.458,0.198 10 false IMO 4.906,2.677 5.365,2.875 0.458,0.198 10 false IMO 5.5,0.156 5.958,0.354 0.458,0.198 10 false IMO
*A for 2TR-FE (for Automatic Transmission) *B for 1TR-FE, 2TR-FE (for Manual Transmission)
*C for 1KD-FTV, 2KD-FTV *D for 1GD-FTV, 2GD-FTV
*E for 1GR-FE - -
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition
Item Content
Tester Connection G45-9 (IMO) - Body ground*1
G83-29 (IMO) - Body ground*2
G86-17 (IMO) - Body ground*3
G88-8 (IMO) - Body ground*4
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

*1: for 1TR-FE, 2TR-FE

*2: for 1KD-FTV, 2KD-FTV

*3: for 1GD-FTV, 2GD-FTV

*4: for 1GR-FE


OK:

Waveform is similar to that shown in the illustration.



Result:
Result Proceed to
OK A
NG (Terminal IMO stuck low (2.4 V or less)) B
NG (Terminal IMO stuck high (12 V) or abnormal waveform) C



A

4.INSPECT ECM (TERMINAL IMI)

B

10.INSPECT ECM (IMO TERMINAL VOLTAGE)

C

7.REPLACE ECM
4.INSPECT ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

B413959C01
0.771,4.219 1.156,4.427 0.385,0.208 1.823,4.219 2.208,4.427 0.385,0.208 2.948,4.208 3.333,4.417 0.385,0.208 3.906,4.219 4.292,4.427 0.385,0.208 4.969,4.208 5.354,4.417 0.385,0.208 5.99,4.208 6.375,4.417 0.385,0.208 1.385,5.417 1.771,5.625 0.385,0.208 3.125,5.417 3.51,5.625 0.385,0.208 3.906,5.417 4.292,5.625 0.385,0.208 2.094,5.406 2.479,5.615 0.385,0.208 4.615,5.417 5,5.625 0.385,0.208 5.375,5.417 5.76,5.625 0.385,0.208 1.458,2.823 1.844,3.031 0.385,0.208 2.74,2.813 3.125,3.021 0.385,0.208 4.156,2.813 4.542,3.021 0.385,0.208 5.292,2.823 5.677,3.031 0.385,0.208 1.333,1.375 1.719,1.583 0.385,0.208 2.677,1.365 3.063,1.573 0.385,0.208 4.219,1.375 4.604,1.583 0.385,0.208 5.49,1.365 5.875,1.573 0.385,0.208 5.823,0.083 6.208,0.292 0.385,0.208 4.656,0.083 5.042,0.292 0.385,0.208 3.385,0.094 3.771,0.302 0.385,0.208 2.156,0.083 2.542,0.292 0.385,0.208 0.865,0.094 1.25,0.302 0.385,0.208 4.958,0.792 5.188,0.208 5.188,0.208 5.344,0.208 true 4.521,2.083 4.75,1.5 4.75,1.5 4.906,1.5 true 4.563,3.833 4.396,4.146 4.396,4.146 4.552,4.146 true 5.906,4.813 6.135,5.375 6.135,5.375 6.292,5.375 true 2.229,6.01 2.333,6.802 2.333,6.802 2.49,6.802 true 0.938,0.125 1.396,0.323 0.458,0.198 10 false C52 3.448,0.135 3.906,0.333 0.458,0.198 10 false C54 4.729,0.115 5.188,0.313 0.458,0.198 10 false G45 5.875,0.104 6.333,0.302 0.458,0.198 10 false G46 2.229,0.115 2.688,0.313 0.458,0.198 10 false C53 3.198,5.448 3.656,5.646 0.458,0.198 10 false C15 2.729,1.396 3.188,1.594 0.458,0.198 10 false C53 4.208,2.844 4.667,3.042 0.458,0.198 10 false G83 5.563,1.396 6.021,1.594 0.458,0.198 10 false G46 1.552,2.854 2.01,3.052 0.458,0.198 10 false C55 2.813,2.844 3.271,3.042 0.458,0.198 10 false C56 4.281,1.396 4.74,1.594 0.458,0.198 10 false G45 5.365,2.854 5.823,3.052 0.458,0.198 10 false G84 0.833,4.25 1.292,4.448 0.458,0.198 10 false C57 1.906,4.25 2.365,4.448 0.458,0.198 10 false C58 2.979,4.25 3.438,4.448 0.458,0.198 10 false C59 3.979,4.25 4.438,4.448 0.458,0.198 10 false C60 5.042,4.25 5.5,4.448 0.458,0.198 10 false G85 6.042,4.25 6.5,4.448 0.458,0.198 10 false G86 1.438,5.448 1.896,5.646 0.458,0.198 10 false G87 2.177,5.448 2.635,5.646 0.458,0.198 10 false G88 3.958,5.448 4.417,5.646 0.458,0.198 10 false C14 4.688,5.448 5.146,5.646 0.458,0.198 10 false C13 5.448,5.448 5.906,5.646 0.458,0.198 10 false C12 1.417,1.406 1.875,1.604 0.458,0.198 10 false C52 0.063,0.063 0.521,0.26 0.458,0.198 12 false *A 0.073,1.385 0.531,1.583 0.458,0.198 12 false *B 0.083,2.792 0.542,2.99 0.458,0.198 12 false *C 0.083,4.208 0.542,4.406 0.458,0.198 12 false *D 0.104,5.406 0.563,5.604 0.458,0.198 12 false *E 0.073,0.24 0.531,0.438 0.458,0.198 10 false *a 0.094,1.594 0.552,1.792 0.458,0.198 10 false *a 0.104,2.979 0.563,3.177 0.458,0.198 10 false *a 0.104,4.385 0.563,4.583 0.458,0.198 10 false *a 0.125,5.583 0.583,5.781 0.458,0.198 10 false *a 0.969,8.26 1.427,8.458 0.458,0.198 10 false GND 3.323,8.344 3.781,8.542 0.458,0.198 10 false *b 5.396,0.135 5.854,0.333 0.458,0.198 10 false IMI 4.969,1.417 5.427,1.615 0.458,0.198 10 false IMI 4.625,4.083 5.083,4.281 0.458,0.198 10 false IMI 6.344,5.292 6.802,5.49 0.458,0.198 10 false IMI 2.531,6.708 2.99,6.906 0.458,0.198 10 false IMI
*A for 2TR-FE (for Automatic Transmission) *B for 1TR-FE, 2TR-FE (for Manual Transmission)
*C for 1KD-FTV, 2KD-FTV *D for 1GD-FTV, 2GD-FTV
*E for 1GR-FE - -
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition
Item Content
Tester Connection G45-10 (IMI) - Body ground*1
G83-30 (IMI) - Body ground*2
G86-16 (IMI) - Body ground*3
G88-10 (IMI) - Body ground*4
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

*1: for 1TR-FE, 2TR-FE

*2: for 1KD-FTV, 2KD-FTV

*3: for 1GD-FTV, 2GD-FTV

*4: for 1GR-FE


OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

5.REGISTER ECU COMMUNICATION ID

NG

12.REPLACE TRANSPONDER KEY ECU ASSEMBLY
5.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

7.REPLACE ECM
7.REPLACE ECM

NEXT

8.REGISTER ECU COMMUNICATION ID
8.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER ENGINE STARTS
9.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ECM WAS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY

10.INSPECT ECM (IMO TERMINAL VOLTAGE)
a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

B413960C01
0.844,0.396 1.24,0.656 0.396,0.26 2.615,0.396 3.01,0.656 0.396,0.26 4.458,0.406 4.854,0.667 0.396,0.26 6.063,0.24 6.458,0.5 0.396,0.26 0.792,1.406 1.073,2.24 1.073,2.24 1.229,2.24 true 2.385,1.719 2.552,2.229 2.552,2.229 2.708,2.229 true 5.24,1.427 5.042,2.198 5.042,2.198 4.875,2.198 true 6.125,1.323 5.917,2.177 5.917,2.177 5.75,2.177 true 0.094,0.208 0.406,0.406 0.313,0.198 10 false *a 0.104,0.042 0.417,0.24 0.313,0.198 12 false *A 1.906,0.031 2.219,0.229 0.313,0.198 12 false *B 3.719,0.042 4.031,0.24 0.313,0.198 12 false *C 5.521,0.052 5.833,0.25 0.313,0.198 12 false *D 1.927,0.198 2.24,0.396 0.313,0.198 10 false *a 3.75,0.208 4.063,0.406 0.313,0.198 10 false *a 5.542,0.219 5.854,0.417 0.313,0.198 10 false *a 1.271,2.167 1.729,2.365 0.458,0.198 10 false IMO 2.76,2.156 3.219,2.354 0.458,0.198 10 false IMO 4.594,2.125 5.052,2.323 0.458,0.198 10 false IMO 5.479,2.104 5.938,2.302 0.458,0.198 10 false IMO 0.917,0.438 1.375,0.635 0.458,0.198 10 false G45 2.698,0.448 3.156,0.646 0.458,0.198 10 false G83 4.531,0.458 4.99,0.656 0.458,0.198 10 false G86 6.135,0.292 6.594,0.49 0.458,0.198 10 false G88
*A for 1TR-FE, 2TR-FE *B for 1KD-FTV, 2KD-FTV
*C for 1GD-FTV, 2GD-FTV *D for 1GR-FE
*a Front view of wire harness connector
(to ECM)
- -


Standard Voltage:
Tester Connection Condition Result
G45-9 (IMO) - Body ground*1
G83-29 (IMO) - Body ground*2
G86-17 (IMO) - Body ground*3
G88-8 (IMO) - Body ground*4
Ignition switch turned to ON using registered key Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform


*1: for 1TR-FE, 2TR-FE

*2: for 1KD-FTV, 2KD-FTV

*3: for 1GD-FTV, 2GD-FTV

*4: for 1GR-FE



Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or Abnormal waveform B



A

11.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM AND BODY GROUND)

B

7.REPLACE ECM
11.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM AND BODY GROUND)
a.

Disconnect the G16 transponder key ECU assembly connector.


b.

Disconnect the G45*1, G83*2, G86*3 or G88*4 ECM connector.

*1: for 1TR-FE, 2TR-FE

*2: for 1KD-FTV, 2KD-FTV

*3: for 1GD-FTV, 2GD-FTV

*4: for 1GR-FE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1TR-FE, 2TR-FE
Tester Connection Condition Specified Condition
G16-12 (EFII) - G45-9 (IMO) Always Below 1 Ω
G16-13 (EFIO) - G45-10 (IMI) Always Below 1 Ω
G45-9 (IMO) - Body ground Always 10 kΩ or higher
G16-12 (EFII) - Body ground Always 10 kΩ or higher
G45-10 (IMI) - Body ground Always 10 kΩ or higher
G16-13 (EFIO) - Body ground Always 10 kΩ or higher

for 1KD-FTV, 2KD-FTV
Tester Connection Condition Specified Condition
G16-12 (EFII) - G83-29 (IMO) Always Below 1 Ω
G16-13 (EFIO) - G83-30 (IMI) Always Below 1 Ω
G83-29 (IMO) - Body ground Always 10 kΩ or higher
G16-12 (EFII) - Body ground Always 10 kΩ or higher
G83-30 (IMI) - Body ground Always 10 kΩ or higher
G16-13 (EFIO) - Body ground Always 10 kΩ or higher

for 1GD-FTV, 2GD-FTV
Tester Connection Condition Specified Condition
G16-12 (EFII) - G86-17 (IMO) Always Below 1 Ω
G16-13 (EFIO) - G86-16 (IMI) Always Below 1 Ω
G86-17 (IMO) - Body ground Always 10 kΩ or higher
G16-12 (EFII) - Body ground Always 10 kΩ or higher
G86-16 (IMI) - Body ground Always 10 kΩ or higher
G16-13 (EFIO) - Body ground Always 10 kΩ or higher

for 1GR-FE
Tester Connection Condition Specified Condition
G16-12 (EFII) - G88-8 (IMO) Always Below 1 Ω
G16-13 (EFIO) - G88-10 (IMI) Always Below 1 Ω
G88-8 (IMO) - Body ground Always 10 kΩ or higher
G16-12 (EFII) - Body ground Always 10 kΩ or higher
G88-10 (IMI) - Body ground Always 10 kΩ or higher
G16-13 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

13.REGISTER KEY
13.REGISTER KEY
a.

Register the key.

HINT:

Refer to Service Bulletin.


Result:
Proceed to
NEXT




NEXT

14.REGISTER ECU COMMUNICATION ID
14.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.


Result:
Proceed to
NEXT




NEXT

15.CHECK WHETHER ENGINE STARTS
15.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG (for 1TR-FE)
NG (for 2TR-FE)
NG (for 1KD-FTV)
NG (for 2KD-FTV)
NG (for 1GD-FTV)
NG (for 2GD-FTV)
NG (for 1GR-FE)



OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG (for 1TR-FE)

NG (for 2TR-FE)

NG (for 1KD-FTV)

NG (for 2KD-FTV)

NG (for 1GD-FTV)

NG (for 2GD-FTV)

NG (for 1GR-FE)