When the communication line (EFIO-IMI) between the transponder key ECU assembly and ECM is stuck on HI output, the ECM stores this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B279A | Theft Deterrent System Communication Line High Fixation | The communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck on HI output (1 trip detection logic*). | ·
Harness or connector ·
ECM ·
Transponder key ECU assembly |
DTC Output Confirmation Operation:
Turn the ignition switch to ON and wait 6 seconds. |
*: Only output while a malfunction is present.
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops) | Engine cannot be started |
| DTC No. | Data List and Active Test |
|---|---|
| B279A | - |
If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
DTC B279A is not output.
| Result | Proceed to |
|---|---|
| B279A is not output | A |
| B279A is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Check that the connectors are properly connected to the ECM and transponder key ECU assembly.
Connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G16 transponder key ECU assembly connector.
Disconnect the G45*1, G83*2, G86*3 or G88*4 ECM connector.
*1: for 1TR-FE, 2TR-FE
*2: for 1KD-FTV, 2KD-FTV
*3: for 1GD-FTV, 2GD-FTV
*4: for 1GR-FE
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-13 (EFIO) - G45-10 (IMI) | Always | Below 1 Ω |
| G45-10 (IMI) - Body ground | Always | 10 kΩ or higher |
| G16-13 (EFIO) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-13 (EFIO) - G83-30 (IMI) | Always | Below 1 Ω |
| G83-30 (IMI) - Body ground | Always | 10 kΩ or higher |
| G16-13 (EFIO) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-13 (EFIO) - G86-16 (IMI) | Always | Below 1 Ω |
| G86-16 (IMI) - Body ground | Always | 10 kΩ or higher |
| G16-13 (EFIO) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-13 (EFIO) - G88-10 (IMI) | Always | Below 1 Ω |
| G88-10 (IMI) - Body ground | Always | 10 kΩ or higher |
| G16-13 (EFIO) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the transponder key ECU assembly with a new one.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Register the key.
refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Register the ECU communication ID.
refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the engine starts with the key.
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG (for 1TR-FE) |
| NG (for 2TR-FE) |
| NG (for 1KD-FTV) |
| NG (for 2KD-FTV) |
| NG (for 1GD-FTV) |
| NG (for 2GD-FTV) |
| NG (for 1GR-FE) |
OK
NG (for 1TR-FE)
NG (for 2TR-FE)
NG (for 1KD-FTV)
NG (for 2KD-FTV)
NG (for 1GD-FTV)
NG (for 2GD-FTV)
NG (for 1GR-FE)