Home › Vehicle Exterior › WINDOW / GLASS › BACK WINDOW GLASS(for Single Cab)
RM3250E _59 Vehicle Exterior _038075 WINDOW / GLASS _0185631 BACK WINDOW GLASS(for Single Cab) A

WINDOW / GLASS  BACK WINDOW GLASS(for Single Cab)  REMOVAL  


PROCEDURE

Hide 67914B 1.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 67913B 2.REMOVE FRONT DOOR SCUFF PLATE RH

Hide 64261C 3.REMOVE UPPER BACK PANEL GARNISH

Hide 62514A 4.REMOVE LOWER QUARTER TRIM PANEL LH

Hide 62513A 5.REMOVE LOWER QUARTER TRIM PANEL RH

Hide 73178A 6.REMOVE SEAT BELT ANCHOR COVER CAP

Hide 62512 7.REMOVE QUARTER INSIDE TRIM BOARD LH

Hide 62511 8.REMOVE QUARTER INSIDE TRIM BOARD RH

Hide 81260A 9.REMOVE MAP LIGHT ASSEMBLY

Hide 74610A 15.REMOVE ASSIST GRIP SUB-ASSEMBLY

Hide 63339A 16.REMOVE ROOF HEADLINING SERVICE HOLE COVER

Hide 63310 17.REMOVE ROOF HEADLINING ASSEMBLY

Hide 64810 18.REMOVE BACK WINDOW ASSEMBLY (for Fixed Type)

NOTICE:
·

Be careful not to damage the back window glass when cutting as the back window glass spacers are installed to the back window glass.


·

The back window glass may fall while performing this procedure. Therefore, use suction cups to hold the back window glass from the outside of the vehicle.



a.
B405947C01
0,0 0,0 false
V100155

Protective Tape


Put protective tape on the body panel around the back window assembly.

NOTICE:

When separating the back window assembly from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.



b.
B405974C01
1.792,0.417 2.198,0.25 false 2.26,0.177 2.573,0.333 0.313,0.156 10 false *a
*a Matchmarks


When reusing back window assembly:

i.

Place adhesive tape on the back window assembly and body panel and use a pen to place matchmarks for installation.


ii.

Install the suction cups to the back window assembly.



c.

w/ Window Defogger System:

Disconnect the back window defogger connector.


d.
B405948C01
0.417,0.75 0.833,0.333 false 3.01,0.76 2.594,0.375 false 0.208,1.396 0.667,1 false 3.24,1.427 2.875,1.042 false 0.208,1.604 0.635,1.885 false 0.979,1.531 1.344,1.823 false 0.896,0.24 1.208,0.396 0.313,0.156 10 false *1 0.729,0.927 1.042,1.083 0.313,0.156 10 false *2 1.375,1.802 1.688,1.958 0.313,0.156 10 false *a 2.375,0.281 2.688,0.479 0.313,0.198 10 false *1 2.667,0.938 2.979,1.135 0.313,0.198 10 false *2 0.688,1.844 1,2.042 0.313,0.198 10 false *a
*1 Back Window Glass Spacer
*2 Back Window Glass Clip
*a Piano Wire


From the interior, insert a piano wire between the vehicle body and back window assembly as shown in the illustration.


e.

Tie objects that can serve as handles (for example, wooden blocks) to all wire ends.


f.

Pull on the ends of the piano wire alternately and leave the back window assembly spacers and back window glass clips when cutting through the adhesive.

NOTICE:
·

Do not forcefully brush the piano wire against the back window assembly.


·

Be careful as the piano wire will break if it crosses itself.




g.

Using suction cups, remove the back window assembly.

NOTICE:

Make sure that the back window assembly does not fall.



Hide 64810 19.REMOVE BACK WINDOW ASSEMBLY (for Slide Type)

NOTICE:

The back window glass may fall while performing this procedure. Therefore, use suction cups to hold the back window glass from the outside of the vehicle.


a.
B405947C01
0,0 0,0 false
V100155

Protective Tape


Put protective tape on the body panel around the back window assembly.

NOTICE:

When separating the back window assembly from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.



b.

Using a knife, cut off the moulding as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.


B416237C01
3.792,0.5 3.948,0.698 0.156,0.198 10 false A 3.823,0.948 3.979,1.146 0.156,0.198 10 true A 5.01,0.792 5.167,0.99 0.156,0.198 10 false B 4.531,0.938 4.688,1.135 0.156,0.198 10 true B 3.823,1.302 3.979,1.5 0.156,0.198 10 true C 3.823,1.792 3.979,1.99 0.156,0.198 10 true C 0.385,2.385 1.156,2.583 0.771,0.198 10 false A - A 3.625,2.344 4.396,2.542 0.771,0.198 10 false B - B 0.354,3.896 1.125,4.094 0.771,0.198 10 false C - C 2.396,2.969 2.708,3.167 0.313,0.198 10 false *a 5.469,2.448 5.781,2.646 0.313,0.198 10 false *a 2.448,4.781 2.76,4.979 0.313,0.198 10 false *a
*a Cut - -



c.

Install the suction cups to the back window assembly.


d.
B416233C01
0.385,0.802 0.802,0.385 true 0.219,1.427 0.594,0.979 true 3.052,0.802 2.563,0.375 true 0.198,1.615 0.646,1.875 0.646,1.875 0.76,1.531 false 3.229,1.417 2.854,1.031 false 0.844,0.333 1.156,0.49 0.313,0.156 10 false *1 0.646,0.896 0.958,1.052 0.313,0.156 10 true *2 0.604,1.885 0.917,2.042 0.313,0.156 10 false *a 2.333,0.302 2.646,0.5 0.313,0.198 10 false *1 2.656,0.927 2.969,1.125 0.313,0.198 10 true *2
*1 Spacer
*2 Clip
*a Piano Wire


From the interior, insert a piano wire between the vehicle body and back window assembly as shown in the illustration.


e.

Tie objects that can serve as handles (for example, wooden blocks) to all wire ends.


f.

Pull on the ends of the piano wire alternately and leave the spacers and clips when cutting through the adhesive.

NOTICE:
·

Do not forcefully brush the piano wire against the back window assembly.


·

Be careful as the piano wire will break if it crosses itself.




g.

Using suction cups, remove the back window assembly.

NOTICE:

Make sure that the back window assembly does not fall.