Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER OIL SEAL › 2015.06–2016.01
RM3250E _52 Drivetrain _038039 AXLE AND DIFFERENTIAL _0186170 FRONT DIFFERENTIAL CARRIER OIL SEAL A

AXLE AND DIFFERENTIAL  FRONT DIFFERENTIAL CARRIER OIL SEAL  REPLACEMENT  


PROCEDURE

Hide 51441 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51442 2.REMOVE NO. 2 ENGINE UNDER COVER

Hide 41204D 5.REMOVE FRONT DRIVE PINION COMPANION FLANGE NUT

a.
C236628N05
1.292,0.542 1.292,0.208 1.292,0.208 1.948,0.208 false 1.99,0.135 2.5,0.406 0.51,0.271 10 false SST

Using SST and a hammer, loosen the staked part of the front drive pinion companion flange nut.

SST
09930-00010  (09931-00010, 09931-00020)


b.
C236629C05
2.219,1.208 2.427,1.031 2.427,1.031 2.656,1.031 false 2.719,0.969 3.156,1.219 0.438,0.25 10 false SST 0.51,0.365 0.677,0.521 0.167,0.156 10 false *a 2.188,1.74 2.354,1.896 0.167,0.156 10 false *b
*a Turn
*b Hold


Using SST to hold the companion flange, remove the front drive pinion companion flange nut.

SST
09330-00021  (09330-00030)


Hide 41204D 6.REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

a.
C326640N01
2.479,1.865 2.125,1.865 2.125,1.865 2.125,1.51 false 2.531,1.781 2.99,1.979 0.458,0.198 10 false SST

Using SST, remove the front drive pinion companion flange sub-assembly with dust deflector.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



Hide 7.REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL

a.
C326641C01
1.448,0.885 1.844,0.51 1.844,0.51 2.083,0.51 true 1.813,1.875 1.438,1.875 1.438,1.875 1.229,1.438 true 2.677,1.854 2.479,1.854 2.479,1.854 2.479,1.542 false 2.167,0.427 2.479,0.625 0.313,0.198 10 false *1 1.885,1.781 2.198,1.979 0.313,0.198 10 false *2 2.74,1.76 3.198,1.958 0.458,0.198 10 false SST
*1 Front Differential Carrier Oil Seal
*2 Front Differential Drive Pinion Oil Slinger


Using SST, remove the front differential carrier oil seal.

SST
09308-10010  


Hide 41214C 8.REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER

a.
C237315

Remove the front differential drive pinion oil slinger from the differential drive pinion.


Hide 41211B 9.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C326642N01
2.5,0.563 2.5,0.229 2.5,0.229 2.781,0.229 false 2.844,0.156 3.219,0.365 0.375,0.208 10 false SST

Using SST, remove the front drive pinion rear tapered roller bearing (inner).

SST
09556-22010  


b.
C326643N01
1.99,0.708 1.99,0.219 1.99,0.219 2.417,0.219 false 2.479,0.135 2.938,0.333 0.458,0.198 10 false SST

Using SST, tap out the front drive pinion rear tapered roller bearing (outer).

SST
09308-00010  


Hide 41115F 10.REMOVE FRONT DIFFERENTIAL OIL STORAGE RING

a.

Using a screwdriver and hammer, tap out the front differential oil storage ring.


Hide 41231F 11.REMOVE FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER

a.
C237692

Remove the front differential drive pinion bearing spacer from the differential drive pinion.


Hide 41231F 12.INSTALL FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER

a.
C237692

Install a new front differential drive pinion bearing spacer.

HINT:

Make sure the front differential drive pinion bearing spacer is installed correctly.



Hide 41115F 13.INSTALL FRONT DIFFERENTIAL OIL STORAGE RING

a.

Using a brass bar and hammer, tap in a new front differential oil storage ring.

NOTICE:

Be careful not to damage the front differential oil storage ring.



Hide 41211B 14.INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C326644N01
0.979,1.469 1.615,1.896 1.615,1.896 1.969,1.896 false 1.469,1.427 1.625,1.896 false 2.021,1.813 2.479,2.01 0.458,0.198 10 false SST

Using SST and a hammer, install the front drive pinion rear tapered roller bearing (outer).

SST
09316-60011  (09316-00011)


b.

Install the front drive pinion rear tapered roller bearing (inner).


Hide 41214C 15.INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER

a.
C237315

Install the front differential drive pinion oil slinger to the differential drive pinion.


Hide 16.INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL

a.

Apply MP grease to the lip of a new front differential carrier oil seal.


b.
C326645C01
2.458,1.823 2.073,1.823 2.073,1.823 2.073,1.531 false 1.375,0.115 1.688,0.313 0.313,0.198 10 false *a 2.51,1.75 2.969,1.948 0.458,0.198 10 false SST
*a Front Differential Carrier Oil Seal Depth


Using SST and a hammer, tap in the front differential carrier oil seal.

SST
09554-22010  

Oil seal depth:

2.7 to 3.3 mm (0.107 to 0.129 in.)



Hide 41204D 17.INSTALL FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

a.
C326646N01
2.479,1.875 2.01,1.875 2.01,1.875 2.01,1.521 false 2.531,1.792 2.99,1.99 0.458,0.198 10 false SST

Using SST, install the front drive pinion companion flange sub-assembly with dust deflector.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



b.

Apply hypoid gear oil LSD to the drive pinion thread and nut seat face.


c.
C282254C02
0.656,0.417 0.896,0.417 0.896,0.417 0.896,0.604 false 3.052,1.115 3.365,1.313 0.313,0.198 10 false *a 0.281,1.063 0.594,1.26 0.313,0.198 10 false *b 0.354,0.344 0.896,0.917 0.542,0.573 10 false SST
*a Turn
*b Hold


Using SST to hold the companion flange, install a new front drive pinion companion flange nut.

SST
09330-00021  (09330-00030)

Limit torque value:

370 N*m (3773 kgf*cm, 273 ft.*lbf) or less



Hide 18.INSPECT TOTAL PRELOAD

a.
C236639

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

Standard Total Preload (Starting Torque):
Item Specified Condition
New bearing 1.3 to 2.9 N*m (14 to 29 kgf*cm, 12 to 25 in.*lbf)
Reused bearing 1.29 to 2.79 N*m (14 to 28 kgf*cm, 12 to 24 in.*lbf)


If necessary, disassemble and inspect the differential.


Hide 41204D 19.STAKE FRONT DRIVE PINION COMPANION FLANGE NUT

a.
C236640

Using a chisel and hammer, stake the front drive pinion companion flange nut.


Hide 51442 22.INSTALL NO. 2 ENGINE UNDER COVER

Hide 51441 23.INSTALL NO. 1 ENGINE UNDER COVER