Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD) › 2015.06–2016.03
RM3250E _57 Power Source / Network _038063 NETWORKING _0186538 CAN COMMUNICATION SYSTEM(for RHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  Open in CAN Main Wire  


DESCRIPTION

There may be an open circuit in the CAN main wire and/or DLC3 CAN branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.

Symptom Trouble Area
The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.
·

CAN main wire or connector

·

No. 1 CAN junction connector

·

No. 2 CAN junction connector

·

ECM

·

Combination meter assembly

·

DLC3 CAN branch wire or connector



WIRING DIAGRAM

C329348E01
0.969,0.74 1.563,1.167 0.594,0.427 10 false 16 1.021,0.281 1.615,0.708 0.594,0.427 10 false 6 2.188,0.281 2.781,0.708 0.594,0.427 10 false 5 2.167,0.74 2.76,1.167 0.594,0.427 10 false 15 0.833,1.292 1.427,1.719 0.594,0.427 10 false G68 0.844,1.458 2.958,1.802 2.115,0.344 10 false No. 2 CAN Junction Connector 2.219,2.25 2.813,2.677 0.594,0.427 10 false 4 2.198,2.708 2.792,3.135 0.594,0.427 10 false 14 3.479,3.208 4.073,3.635 0.594,0.427 10 false G8 3.438,3.365 4.031,3.792 0.594,0.427 10 false DLC3 3,3.969 3.594,4.396 0.594,0.427 10 false 36 3,4.427 3.594,4.854 0.594,0.427 10 false 35 3.135,4.958 3.729,5.385 0.594,0.427 10 false G9 3.135,5.125 5.063,5.458 1.927,0.333 10 false Combination Meter Assembly 0.677,4.99 1.271,5.396 0.594,0.406 10 false G67 0.688,5.156 2.75,5.542 2.063,0.385 10 false No. 1 CAN Junction Connector 6.417,1.24 6.875,1.615 0.458,0.375 10 false ECM 6.24,0.99 6.833,1.417 0.594,0.427 10 false CANL 6.229,0.281 6.823,0.708 0.594,0.427 10 false CANH 4.448,0.375 5.042,0.802 0.594,0.427 10 false G45 5.354,0.375 5.948,0.802 0.594,0.427 10 false G88 4.896,0.385 5.49,0.813 0.594,0.427 10 false G85 5.802,0.375 6.396,0.802 0.594,0.427 10 false G83 4.427,0.156 5.021,0.583 0.594,0.427 10 false 13*1 5.344,0.167 5.938,0.594 0.594,0.427 10 false 31*3 5.792,0.167 6.385,0.594 0.594,0.427 10 false 24*4 5.792,0.635 6.385,1.063 0.594,0.427 10 false 23*4 4.896,0.156 5.49,0.583 0.594,0.427 10 false 17*2 4.896,0.635 5.49,1.063 0.594,0.427 10 false 28*2 4.427,0.635 5.021,1.063 0.594,0.427 10 false 14*1 5.354,0.635 5.948,1.063 0.594,0.427 10 false 25*3 4.604,2.969 6.396,3.313 1.792,0.344 10 false *2: for 1GD-FTV, 2GD-FTV 4.594,2.646 6.24,3 1.646,0.354 10 false *1: for 2TR-FE 5.792,0.854 6.385,1.281 0.594,0.427 10 false G83 5.354,0.844 5.948,1.271 0.594,0.427 10 false G88 4.896,0.854 5.49,1.281 0.594,0.427 10 false G85 4.448,0.854 5.042,1.281 0.594,0.427 10 false G45 1.031,2.25 1.625,2.677 0.594,0.427 10 false 6 0.969,2.719 1.563,3.146 0.594,0.427 10 false 16 2.219,3.958 2.813,4.385 0.594,0.427 10 false 5 2.198,4.427 2.792,4.854 0.594,0.427 10 false 15 3.271,2.344 3.865,2.771 0.594,0.427 10 false CANH 3.271,2.813 3.865,3.24 0.594,0.427 10 false CANL 3.281,3.958 3.875,4.385 0.594,0.427 10 false CANH 3.281,4.677 3.875,5.104 0.594,0.427 10 false CANL 4.604,3.271 6.25,3.625 1.646,0.354 10 false *3: for 1GR-FE 4.615,3.583 6.406,3.927 1.792,0.344 10 false *4: for 1KD-FTV, 2KD-FTV 3.042,2.25 3.635,2.677 0.594,0.427 10 false 6 3,2.719 3.594,3.146 0.594,0.427 10 false 14

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When replacing the combination meter assembly, make sure to replace it with a new one.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)
a.
C300827C23
0.115,0.99 0.521,1.25 0.406,0.26 1.948,0.917 1.552,0.385 1.552,0.385 1.406,0.385 true 1.938,1.49 2.052,1.906 2.052,1.906 2.167,1.906 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 0.219,1.052 0.5,1.219 0.281,0.167 10 false G8 1,0.333 1.49,0.479 0.49,0.146 10 false CANH 2.229,1.844 2.844,2.042 0.615,0.198 10 false CANL
*a Front view of DLC3


Disconnect the cable from the negative (-) battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-6 (CANH) - G8-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


NOTICE:

When the measured value is 133 Ω or higher and a CAN communication system DTC is output, there may be a fault besides disconnection of the DLC3 branch line. For that reason, troubleshooting should be performed again from How to Proceed with Troubleshooting after repairing the trouble area.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>HOW TO PROCEED WITH TROUBLESHOOTING



Result:
Proceed to
OK
NG



OK

2.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 CAN JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

2.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 CAN JUNCTION CONNECTOR)
a.
C300860C08
1.5,0.167 1.927,0.458 0.427,0.292 2.5,1.708 2.354,1.708 2.354,1.708 2.021,1.25 true 1.052,0.49 1.219,0.49 1.219,0.49 1.5,1.01 true 2.5,0.49 2.344,0.49 2.344,0.49 2.01,1.042 true 1.083,1.698 1.24,1.698 1.24,1.698 1.51,1.281 true 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 0.531,0.417 1.125,0.573 0.594,0.156 10 false CANH*b 2.583,0.427 3.177,0.583 0.594,0.156 10 false CANH*c 0.573,1.635 1.167,1.792 0.594,0.156 10 false CANL*b 2.594,1.625 3.188,1.781 0.594,0.156 10 false CANL*c 1.594,0.229 1.906,0.417 0.313,0.188 10 false G67
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Combination Meter Assembly
*c to No. 2 CAN Junction Connector


Disconnect the No. 1 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G67-5 (CANH) - G67-15 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G67-6 (CANH) - G67-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to No. 2 CAN junction connector CAN main wire) B
NG (to combination meter assembly CAN main wire) C



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

3.CONNECT CONNECTOR

C

13.CONNECT CONNECTOR
3.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 CAN JUNCTION CONNECTOR)
4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 CAN JUNCTION CONNECTOR)
a.
C300860C09
1.5,0.167 1.927,0.458 0.427,0.292 2.5,1.708 2.354,1.708 2.354,1.708 2.01,1.25 true 1.052,0.49 1.219,0.49 1.219,0.49 1.5,1.052 true 2.5,0.49 2.344,0.49 2.344,0.49 2.031,1.031 true 1.083,1.698 1.24,1.698 1.24,1.698 1.521,1.271 true 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 0.531,0.417 1.125,0.573 0.594,0.156 10 false CANH*b 2.583,0.427 3.177,0.583 0.594,0.156 10 false CANH*c 0.573,1.635 1.167,1.792 0.594,0.156 10 false CANL*b 2.594,1.625 3.188,1.781 0.594,0.156 10 false CANL*c 1.594,0.229 1.906,0.417 0.313,0.188 10 false G68
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to ECM
*c to No. 1 CAN Junction Connector


Disconnect the No. 2 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G68-5 (CANH) - G68-15 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G68-6 (CANH) - G68-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to ECM CAN main wire) (for 2TR-FE) B
NG (to ECM CAN main wire) (for 1GR-FE) C
NG (to ECM CAN main wire) (for 1KD-FTV, 2KD-FTV) D
NG (to ECM CAN main wire) (for 1GD-FTV, 2GD-FTV) E
NG (to No. 1 CAN junction connector CAN main wire) F



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

5.CONNECT CONNECTOR

C

7.CONNECT CONNECTOR

D

9.CONNECT CONNECTOR

E

11.CONNECT CONNECTOR

F

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

5.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 2 CAN JUNCTION CONNECTOR)
6.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 2 CAN JUNCTION CONNECTOR)
a.
C317098C06
1.458,0.458 1.906,0.74 0.448,0.281 2.344,3.167 2.198,3.167 2.198,3.167 2.073,2 true 2.521,2.854 2.375,2.854 2.375,2.854 2.219,2.01 true 1.552,0.51 2.01,0.708 0.458,0.198 10 false G45 2.583,2.771 3.208,2.99 0.625,0.219 10 false CANL 2.427,3.063 3.052,3.302 0.625,0.24 10 false CANH 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G45-13 (CANH) - G45-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 2 CAN JUNCTION CONNECTOR)

7.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

8.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 2 CAN JUNCTION CONNECTOR)
8.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 2 CAN JUNCTION CONNECTOR)
a.
C329346C01
2.344,0.938 2.813,1.229 0.469,0.292 0.854,1.969 0.99,1.969 0.99,1.969 1.292,1.573 true 0.813,1.042 0.948,1.042 0.948,1.042 1.292,1.375 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 0.406,1.885 0.854,2.083 0.448,0.198 10 false CANH 2.448,1.01 3.063,1.208 0.615,0.198 10 false G88 0.385,0.958 0.823,1.156 0.438,0.198 10 false CANL
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G88-31 (CANH) - G88-25 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 2 CAN JUNCTION CONNECTOR)

9.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

10.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 2 CAN JUNCTION CONNECTOR)
10.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 2 CAN JUNCTION CONNECTOR)
a.
C317098C07
1.458,0.823 1.906,1.104 0.448,0.281 0.688,1.521 0.833,1.521 0.833,1.521 2.063,2.083 true 0.688,3.135 0.833,3.135 0.833,3.135 1.938,2.167 true 1.563,0.896 2.021,1.094 0.458,0.198 10 false G83 0.271,1.458 0.75,1.656 0.479,0.198 10 false CANH 0.26,3.063 0.708,3.26 0.448,0.198 10 false CANL 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G83-24 (CANH) - G83-23 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 2 CAN JUNCTION CONNECTOR)

11.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

12.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 2 CAN JUNCTION CONNECTOR)
12.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 2 CAN JUNCTION CONNECTOR)
a.
C317098C10
1.458,0.823 1.906,1.104 0.448,0.281 0.667,1.885 0.813,1.885 0.813,1.885 1.063,2.094 true 0.677,2.906 0.823,2.906 0.823,2.906 1.073,2.344 true 1.563,0.896 2.021,1.094 0.458,0.198 10 false G85 0.208,1.792 0.688,1.99 0.479,0.198 10 false CANH 0.24,2.823 0.688,3.021 0.448,0.198 10 false CANL 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G85-17 (CANH) - G85-28 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 2 CAN JUNCTION CONNECTOR)

13.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connectors.


Result:
Proceed to
NEXT



NEXT

14.CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ASSEMBLY - NO. 1 CAN JUNCTION CONNECTOR)
14.CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ASSEMBLY - NO. 1 CAN JUNCTION CONNECTOR)
a.
C300838C12
0.427,1.115 0.854,1.396 0.427,0.281 1.677,2.802 1.854,2.802 1.854,2.802 2.208,2.427 true 2.75,2.802 2.594,2.802 2.594,2.802 2.344,2.417 true 0.167,0.156 0.479,0.313 0.313,0.156 10 false *a 2.792,2.729 3.406,2.927 0.615,0.198 10 false CANH 1.292,2.719 1.906,2.917 0.615,0.198 10 false CANL 0.552,1.188 0.833,1.385 0.281,0.198 10 false G9
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-36 (CANH) - G9-35 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (COMBINATION METER ASSEMBLY - NO. 1 CAN JUNCTION CONNECTOR)