Home › Vehicle Exterior › DOOR / HATCH › HOOD LOCK CONTROL CABLE ASSEMBLY(for LHD)
RM3250E _59 Vehicle Exterior _038077 DOOR / HATCH _0188852 HOOD LOCK CONTROL CABLE ASSEMBLY(for LHD) A

DOOR / HATCH  HOOD LOCK CONTROL CABLE ASSEMBLY(for LHD)  INSTALLATION  


PROCEDURE

Hide 53630 1.INSTALL HOOD LOCK CONTROL CABLE ASSEMBLY

a.
B277362C11
1.719,1.323 2.458,1.323 false 1.542,1.229 1.729,1.396 0.188,0.167 10 false *1
*1 String


Tie the string that was passed through the engine compartment to the end of the hood lock control cable assembly as shown in the illustration.

HINT:

Use a length of string long enough to pass through the engine compartment.



b.

Pass the hood lock control cable assembly through the vehicle body, and then attach the grommet and each clamp.


c.

Untie the string from the hood lock control cable assembly.

B408954C07
5.698,1.656 5.698,1.49 5.698,1.49 5.906,1.49 true 5.479,2 5.948,2 true 5.375,3.313 5.781,3.313 5.781,3.313 5.917,3.104 true 5.51,2.865 5.51,2.625 5.51,2.625 5.656,2.625 true 3.073,3.26 3.281,3.26 true 2.813,2.958 3.073,2.958 true 3.792,2.917 4.146,2.917 true 4.208,3.25 4.417,3.25 true 1.813,3.156 1.813,2.917 1.813,2.917 1.958,2.917 true 1.656,3.594 2.094,3.594 true 5.51,1 5.667,1 5.667,1 5.771,0.781 true 5.531,0.573 5.719,0.573 true 5.344,1.885 5.563,2.104 0.219,0.219 10 true *1 5.885,1.396 6.083,1.615 0.198,0.219 10 true *2 5.208,3.188 5.406,3.375 0.198,0.188 10 true *1 5.625,2.542 5.823,2.729 0.198,0.188 10 true *3 3.198,3.167 3.396,3.354 0.198,0.188 10 true *3 2.698,2.854 2.896,3.042 0.198,0.188 10 true *1 3.688,2.802 3.885,2.99 0.198,0.188 10 true *1 4.385,3.156 4.583,3.344 0.198,0.188 10 true *3 1.938,2.844 2.135,3.031 0.198,0.188 10 true *3 1.5,3.479 1.698,3.667 0.198,0.188 10 true *1 5,0.146 5.25,0.365 0.25,0.219 10 true *A 5.313,0.885 5.521,1.073 0.208,0.188 10 true *1 5.708,0.469 5.906,0.667 0.198,0.198 10 true *3
*A for Manual Transmission - -
*1 Hood Lock Control Cable Assembly *2 Grommet
*3 Clamp - -



Hide 53601 2.INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.
B393838

Connect the hood lock control cable assembly to the hood lock control lever sub-assembly.


b.
B408953

Attach the claw to install the hood lock control lever sub-assembly.


Hide 53510 3.INSTALL HOOD LOCK ASSEMBLY

a.
B408974

Apply MP grease to the sliding parts of the hood lock assembly.


b.

Connect the hood lock control cable assembly to the hood lock assembly.


c.
B408956C02
0,0 0,0 false
V100135

Bolt
V100136

Connector


Install the hood lock assembly with the 3 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


d.

Connect the connector.


Hide 53117C 4.INSTALL NO. 1 RADIATOR GRILLE RETAINER