Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY › 2015.06–2016.03
RM3250E _58 Vehicle Interior _038070 SUPPLEMENTAL RESTRAINT SYSTEMS _0189246 CURTAIN SHIELD AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 62180A 4.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH

CAUTION:
B399183C01
0.667,0.5 0.823,0.698 0.156,0.198 10 false .
V100155

Deployment Side


·

When storing the curtain shield airbag assembly LH, keep the airbag deployment side facing upward.

·

If the airbag deploys for any reason, it may cause a serious accident.



a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.
B409645C01
0.885,0.583 1.26,0.313 true 1.302,0.208 1.615,0.365 0.313,0.156 10 false *a
*a Connector Lock
V100155

Protective Tape
V113147

Release in this Direction


Using a screwdriver, pull up the connector lock and disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Tape the screwdriver tip before use.



d.

Remove the clip.

NOTICE:

The clip must not be reused.


HINT:

Use the same procedure for the other clips.


i.
B378006C01
2.458,0.917 2.781,0.917 false 2.823,0.833 3.135,1.031 0.313,0.198 10 false *1
*1 Pin


Using needle-nose pliers, release the lock by pinching the 2 locks of the pin, and then pull out the pin from the clip.


ii.
B378358

Using 2 screwdrivers, detach the clip by inserting the screwdrivers into the groove of the clip as shown in the illustration, and then remove the clip from the vehicle body.



e.

for Single Cab:

i.

Remove the 2 bolts.

NOTICE:

The bolts must not be reused.



ii.

Detach the claw and remove the curtain shield airbag assembly LH.

B409646



f.

for Double Cab:

i.

Remove the 2 bolts.

NOTICE:

The bolts must not be reused.



ii.

Detach the claw and remove the curtain shield airbag assembly LH.

B409647



g.

for Smart Cab:

i.

Remove the 2 bolts.

NOTICE:

The bolts must not be reused.



ii.

Detach the claw and remove the curtain shield airbag assembly LH.

B409648