Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING(for Smart Cab) › 2015.06–2016.03
RM3250E _58 Vehicle Interior _037970 INTERIOR PANELS / TRIM _0189531 ROOF HEADLINING(for Smart Cab) A

INTERIOR PANELS / TRIM  ROOF HEADLINING(for Smart Cab)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



CAUTION:
B414214

w/ Airbag System:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION (w/ Airbag System)

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Airbag System)

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.REMOVE FRONT SEAT ASSEMBLY LH

Hide 4.REMOVE FRONT SEAT ASSEMBLY RH

Hide 74610A 5.REMOVE ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)

Hide 62212 6.REMOVE FRONT PILLAR GARNISH LH

Hide 62211 7.REMOVE FRONT PILLAR GARNISH RH

Hide 8.REMOVE REAR SEAT CUSHION ASSEMBLY (for RHD)

Hide 64271C 9.REMOVE BACK PANEL TRIM

a.
B404509C01
2.958,1.042 3.146,1.042 true 3.167,0.948 3.396,1.104 0.229,0.156 10 true *a
*a Protective Tape


Put protective tape around the back panel trim.


b.
B404510C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw and clip and remove the back panel trim.


Hide 62514A 10.REMOVE LOWER QUARTER TRIM PANEL LH

a.
B421117

for RHD:

i.

Remove the bolt and disconnect the rear seat outer belt assembly LH.



b.
B404512C01
2.417,1.031 2.729,1.188 0.313,0.156 10 false *1
*1 Front Door Opening Trim Weatherstrip LH


Disconnect the front door opening trim weatherstrip LH in the range shown in the illustration.


c.
B404513C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw and clip and remove the lower quarter trim panel LH.


Hide 62513A 11.REMOVE LOWER QUARTER TRIM PANEL RH

a.
B421122

for RHD:

i.

Remove the bolt and disconnect the rear seat outer belt assembly RH.



b.
B404515C01
0.875,0.99 1.188,1.146 0.313,0.156 10 false *1
*1 Front Door Opening Trim Weatherstrip RH


Disconnect the front door opening trim weatherstrip RH in the range shown in the illustration.


c.
B404516C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw and clip and remove the lower quarter trim panel RH.


Hide 73178C 12.REMOVE SEAT BELT ANCHOR COVER CAP (for RHD)

HINT:

Use the same procedure for both seat belt anchor cover caps.


a.
B421118C01
1.958,0.833 2.75,0.656 true 2.792,0.542 3.104,0.698 0.313,0.156 10 false *a
*a Protective Tape


Put protective tape around the seat belt anchor cover cap.


b.
B421119C01
2.563,1.531 2.021,0.833 true 2.583,1.542 2.896,1.698 0.313,0.156 10 false *a
*a Protective Tape
V113146

Insert Thin-bladed Screwdriver Here
V113147

Remove in this Direction


Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the seat belt anchor cover cap.

HINT:

Tape the thin-bladed screwdriver tip before use.



Hide 62512 13.REMOVE QUARTER INSIDE TRIM BOARD LH

a.
B421121

for RHD:

i.

Remove the bolt and disconnect the rear seat outer belt assembly LH.



b.
B404518C01
2.667,1.063 2.979,1.219 0.313,0.156 10 false *1
*1 Front Door Opening Trim Weatherstrip LH


Disconnect the front door opening trim weatherstrip LH in the range shown in the illustration.


c.
B404519C01
0,0 0,0 false
V113146

Insert Clip Remover Here
V113147

Remove in this Direction


Insert a clip remover at the position shown in the illustration and pull as shown to detach the clip and remove the quarter inside trim board LH.


Hide 62511 14.REMOVE QUARTER INSIDE TRIM BOARD RH

a.
B421126

for RHD:

i.

Remove the bolt and disconnect the rear seat outer belt assembly RH.



b.
B404521C01
0.479,1.073 0.792,1.229 0.313,0.156 10 false *1
*1 Front Door Opening Trim Weatherstrip RH


Disconnect the front door opening trim weatherstrip RH in the range shown in the illustration.


c.
B404522C01
0,0 0,0 false
V113146

Insert Clip Remover Here
V113147

Remove in this Direction


Insert a clip remover at the position shown in the illustration and pull as shown to detach the clip and remove the quarter inside trim board RH.


Hide 81260A 15.REMOVE MAP LIGHT ASSEMBLY

Hide 81240 16.REMOVE NO. 1 ROOM LIGHT ASSEMBLY

Hide 74325 17.REMOVE VISOR BRACKET COVER LH

a.

Open the visor assembly LH.


b.
B404635C01
0.667,1.427 1.198,1.677 true 0.458,1.292 0.688,1.448 0.229,0.156 10 true *a
*a Protective Tape
V113146

Insert Thin-bladed Screwdriver Here


Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the visor bracket cover LH.

HINT:

Tape the thin-bladed screwdriver tip before use.



Hide 74325 18.REMOVE VISOR BRACKET COVER RH

a.

Open the visor assembly RH.


b.
B404636C01
2.188,1.625 2.792,1.365 true 2.802,1.229 3.031,1.385 0.229,0.156 10 true *a
*a Protective Tape
V113146

Insert Thin-bladed Screwdriver Here


Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the visor bracket cover RH.

HINT:

Tape the thin-bladed screwdriver tip before use.



Hide 74320 19.REMOVE VISOR ASSEMBLY LH

a.
B404637

Remove the 2 screws.


b.
B404639C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Pull in the direction (1) shown in the illustration to disconnect the visor assembly LH from the visor holder.


c.

Pull in the direction (2) shown in the illustration to remove the visor assembly LH.


Hide 74310 20.REMOVE VISOR ASSEMBLY RH

a.
B404638

Remove the 2 screws.


b.
B404640C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Pull in the direction (1) shown in the illustration to disconnect the visor assembly RH from the visor holder.


c.

Pull in the direction (2) shown in the illustration to remove the visor assembly RH.


Hide 74348 21.REMOVE VISOR HOLDER

HINT:

Use the same procedure for both visor holders.


a.
B404621C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Turn the visor holder clockwise approximately 45° and pull it out as shown in the illustration.


b.

Detach the claw and remove the visor holder.


Hide 74610A 22.REMOVE ASSIST GRIP SUB-ASSEMBLY

HINT:

w/ Assist Grip:

Use the same procedure for both assist grip sub-assemblies.


a.
B404479C01
1.042,1.167 1.74,1.281 true 1.771,1.229 1.99,1.385 0.219,0.156 10 true *a
*a Protective Tape


Put protective tape around the assist grip sub-assembly.


b.
B404480C01
0.875,0.76 0.427,0.406 true 0.198,0.271 0.427,0.427 0.229,0.156 10 true *a
*a Protective Tape
V113146

Insert Thin-bladed Screwdriver Here
V113147

Remove in this Direction


Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and open the assist grip cover.

HINT:

Tape the thin-bladed screwdriver tip before use.



c.
B404483

Remove the 2 bolts and assist grip sub-assembly.


Hide 62432C 23.REMOVE FRONT ROOF SIDE RAIL GARNISH LH

a.
B404524C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the clip and remove the front roof side rail garnish LH.


Hide 62431C 24.REMOVE FRONT ROOF SIDE RAIL GARNISH RH

a.
B404526C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the clip and remove the front roof side rail garnish RH.


Hide 63339A 25.REMOVE ROOF HEADLINING SERVICE HOLE COVER (w/o Assist Grip)

a.
B410866

Using a clip remover, remove the 2 roof headlining service hole covers.


Hide 63310 26.REMOVE ROOF HEADLINING ASSEMBLY

a.
B404484

Disconnect the connector and detach the clamp from the front pillar LH.


b.
B404528C01
1.5,1.719 1.813,1.875 0.313,0.156 10 false *1
*1 Front Door Opening Trim Weatherstrip LH


Disconnect the front door opening trim weatherstrip LH in the range shown in the illustration.


c.
B404529C01
1.531,1.792 1.844,1.948 0.313,0.156 10 false *1
*1 Front Door Opening Trim Weatherstrip RH


Disconnect the front door opening trim weatherstrip RH in the range shown in the illustration.


d.
B404531

Using a clip remover, remove the 3 clips.


e.
B404532C01
0,0 0,0 false
V113147

Remove in this Direction


Turn the roof headlining assembly diagonally and bend slightly to remove it from the front door.

NOTICE:
·

Make sure wrinkles do not form in the roof headlining assembly during removal.

·

Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

·

Do not damage the roof headlining assembly or vehicle interior.




Hide 66423 27.REMOVE FRONT SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

a.
B404491

Detach the claw and remove the front side rail spacer LH.


Hide 66413B 28.REMOVE FRONT SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

a.
B404492

Detach the claw and remove the front side rail spacer RH.


Hide 66424 29.REMOVE REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

a.
B404534

Detach the claw and remove the rear side rail spacer LH.


Hide 66414A 30.REMOVE REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

a.
B404535

Detach the claw and remove the rear side rail spacer RH.


Hide 66425A 31.REMOVE REAR NO. 2 SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

a.
B404536

Detach the claw and remove the rear No. 2 side rail spacer LH.


Hide 66415A 32.REMOVE REAR NO. 2 SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

a.
B404537

Detach the claw and remove the rear No. 2 side rail spacer RH.


Hide 67914B 33.REMOVE FRONT DOOR SCUFF PLATE LH

a.
B404503C01
0.948,1.583 1.365,1.167 true 0.802,1.573 1.115,1.729 0.313,0.156 10 false *a
*a Protective Tape


Put protective tape around the front door scuff plate LH.


b.
B404504C01
0,0 0,0 false
V113146

Insert Moulding Remover D Here
V113147

Remove in this Direction


Insert moulding remover D at the position shown in the illustration and pull as shown to detach the clip and claw and remove the front door scuff plate LH.


Hide 67913B 34.REMOVE FRONT DOOR SCUFF PLATE RH

a.
B404506C01
2.51,1.667 2.125,1.24 true 2.51,1.677 2.823,1.833 0.313,0.156 10 false *a
*a Protective Tape


Put protective tape around the front door scuff plate RH.


b.
B404507C01
0,0 0,0 false
V113146

Insert Moulding Remover D Here
V113147

Remove in this Direction


Insert moulding remover D at the position shown in the illustration and pull as shown to detach the clip and claw and remove the front door scuff plate RH.


Hide 58774A 35.REMOVE LUGGAGE COMPARTMENT SIDE COVER LH

a.
B404541C01
2.854,1.146 3.083,1.302 0.229,0.156 10 true *1
*1 Front Door Opening Trim Weatherstrip LH


Disconnect the front door opening trim weatherstrip LH in the range shown in the illustration.


b.
B404542C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw and remove the luggage compartment side cover LH.


Hide 58773A 36.REMOVE LUGGAGE COMPARTMENT SIDE COVER RH

a.
B404544C01
0.771,1.052 1.01,1.208 0.24,0.156 10 true *1
*1 Front Door Opening Trim Weatherstrip RH


Disconnect the front door opening trim weatherstrip RH in the range shown in the illustration.


b.
B404545C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw and remove the luggage compartment side cover RH.