Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
55302A
1.INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY
Attach the guide to install the upper instrument panel sub-assembly.
Attach the clip as shown in the illustration.
|
Install in this Direction | - | - |
w/ Front Passenger Airbag:
Install the passenger airbag installation bolt <C>.
Install the 2 clips <B>.
Connect the connector and attach the clamp.
| *A | w/ Smart Entry and Start System | *B | w/ Front Passenger Airbag |
| *a | Passenger Airbag Installation Bolt <C> | *b | Clip <B> |
| *c | Connector | *d | Passenger Airbag Connector |
w/ Front Passenger Airbag:
| *a | Lock Slider |
| *b | Lock Position |
Connect the passenger airbag connector.
When handling the passenger airbag connector, take care not to damage the airbag wire harness.
Check that the lock slider is in the lock position.
62212
2.INSTALL FRONT PILLAR GARNISH LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Attach the guide and clip to install the front pillar garnish LH as shown in the illustration.
| *1 | Front Door Opening Trim Weatherstrip LH |
Connect the front door opening trim weatherstrip LH in the range shown in the illustration.
62211
3.INSTALL FRONT PILLAR GARNISH RH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Attach the guide and clip to install the front pillar garnish RH as shown in the illustration.
| *1 | Front Door Opening Trim Weatherstrip RH |
Connect the front door opening trim weatherstrip RH in the range shown in the illustration.
74610A
4.INSTALL ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)
Use the same procedure for both assist grip sub-assemblies.
Install the assist grip sub-assembly with the 2 bolts.
Attach the claw to close the assist grip covers.
55317A
5.INSTALL INSTRUMENT SIDE PANEL RH
w/ Airbag Cut Off Switch:
Connect the connector.
|
Install in this Direction |
Attach the guide as shown in the illustration.
|
Install in this Direction |
Attach the claw and clip to install the instrument side panel RH as shown in the illustration.
| *1 | Front Door Opening Trim Weatherstrip RH |
Connect the front door opening trim weatherstrip RH in the range shown in the illustration.
62111C
6.INSTALL COWL SIDE TRIM BOARD RH
| *a | Cap Nut |
|
Install in this Direction |
Attach the clip to install the cowl side trim board RH as shown in the illustration.
Install the cap nut.
67913B
7.INSTALL FRONT DOOR SCUFF PLATE RH
for Double Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Double Cab)>INSTALLATION
for Single Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Single Cab)>INSTALLATION
for Smart Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Smart Cab)>INSTALLATION
55660
8.INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
|
Install in this Direction |
Attach the clip to install the No. 2 instrument panel register assembly as shown in the illustration.
55041B
9.INSTALL NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY
|
Install in this Direction |
Attach the clip and guide to install the No. 1 instrument panel box door sub-assembly as shown in the illustration.
55470
10.INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY
Attach the clip to install the instrument cluster finish panel garnish assembly as shown in the illustration.
Attach the clips in the order shown in the illustration.
There is no installation order for clip A shown in the illustration.
|
Install in this Direction | - | - |
55318C
11.INSTALL INSTRUMENT SIDE PANEL LH
|
Install in this Direction |
Attach the guide as shown in the illustration.
|
Install in this Direction |
Attach the claw and clip to install the instrument side panel LH as shown in the illustration.
| *1 | Front Door Opening Trim Weatherstrip LH |
Connect the front door opening trim weatherstrip LH in the range shown in the illustration.
62112
12.INSTALL COWL SIDE TRIM BOARD LH
| *a | Cap Nut |
|
Install in this Direction |
Attach the clip to install the cowl side trim board LH as shown in the illustration.
Install the cap nut.
67914B
13.INSTALL FRONT DOOR SCUFF PLATE LH
for Double Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Double Cab)>INSTALLATION
for Single Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Single Cab)>INSTALLATION
for Smart Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Smart Cab)>INSTALLATION
55650
14.INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
|
Install in this Direction |
Attach the clip to install the No. 1 instrument panel register assembly as shown in the illustration.
83100
15.INSTALL COMBINATION METER ASSEMBLY
55410C
16.INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
|
Install in this Direction |
Attach the claw, clip and guide to install the instrument cluster finish panel assembly as shown in the illustration.
| *a | Clip <A> |
Install the 2 clips <A>.
45100
17.INSTALL STEERING WHEEL ASSEMBLY
18.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Airbag System)
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
19.CHECK SRS WARNING LIGHT (w/ Airbag System)