Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
66424
1.INSTALL REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)
Attach the claw to install the rear side rail spacer LH.
66414A
2.INSTALL REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)
Attach the claw to install the rear side rail spacer RH.
66423
3.INSTALL FRONT SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)
Attach the claw to install the front side rail spacer LH.
66413B
4.INSTALL FRONT SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)
Attach the claw to install the front side rail spacer RH.
63310
5.INSTALL ROOF HEADLINING ASSEMBLY
w/ Overhead Console:
|
Movement Direction |
Insert the roof headlining assembly into the cabin from the front door.
Check that the corners of the roof headlining assembly are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.
Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining assembly or vehicle interior.
Install the visor holder as shown in the illustration.
|
Install in this Direction |
Attach the claw to install the visor holder as shown in the illustration.
Use the same procedure for both visor holders.
Install the roof headlining assembly with the 3 clips.
w/o Overhead Console:
|
Movement Direction |
Insert the roof headlining assembly into the cabin from the front door.
Check that the corners of the roof headlining assembly are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.
Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining assembly or vehicle interior.
Install the visor holder as shown in the illustration.
|
Install in this Direction |
Attach the claw to install the visor holder as shown in the illustration.
Use the same procedure for both visor holders.
Install the roof headlining assembly with the 3 clips.
| *1 | Front Door Opening Trim Weatherstrip LH |
Connect the front door opening trim weatherstrip LH in the range shown in the illustration.
| *1 | Front Door Opening Trim Weatherstrip RH |
Connect the front door opening trim weatherstrip RH in the range shown in the illustration.
Connect the connector and attach the clamp to the front pillar LH.
63339A
6.INSTALL ROOF HEADLINING SERVICE HOLE COVER (w/o Assist Grip)
Install the 2 roof headlining service hole covers.
74610A
7.INSTALL ASSIST GRIP SUB-ASSEMBLY
w/ Assist Grip:
Use the same procedure for both assist grip sub-assemblies.
Install the assist grip sub-assembly with the 2 bolts.
Attach the claw to close the assist grip cover.
74320
8.INSTALL VISOR ASSEMBLY LH
Install the visor assembly LH with the 2 screws.
Connect the visor assembly LH to the visor holder.
74310
9.INSTALL VISOR ASSEMBLY RH
Install the visor assembly RH with the 2 screws.
Connect the visor assembly RH to the visor holder.
74325
10.INSTALL VISOR BRACKET COVER LH
|
Install in this Direction |
Attach the claw to install the visor bracket cover LH as shown in the illustration.
74325
11.INSTALL VISOR BRACKET COVER RH
|
Install in this Direction |
Attach the claw to install the visor bracket cover RH as shown in the illustration.
81260A
12.INSTALL MAP LIGHT ASSEMBLY
w/ Overhead Console:
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>INSTALLATION
w/o Overhead Console:
Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT>INSTALLATION
62512
13.INSTALL QUARTER INSIDE TRIM BOARD LH
|
Install in this Direction |
Attach the clip to install the quarter inside trim board LH as shown in the illustration.
| *1 | Front Door Opening Trim Weatherstrip LH |
Connect the front door opening trim weatherstrip LH in the range shown in the illustration.
Connect the front seat outer belt assembly LH with the bolt.
62511
14.INSTALL QUARTER INSIDE TRIM BOARD RH
|
Install in this Direction |
Attach the clip to install the quarter inside trim board RH as shown in the illustration.
| *1 | Front Door Opening Trim Weatherstrip RH |
Connect the front door opening trim weatherstrip RH in the range shown in the illustration.
Connect the front seat outer belt assembly RH with the bolt.
73178A
15.INSTALL SEAT BELT ANCHOR COVER CAP
Use the same procedure for both seat belt anchor cover caps.
|
Install in this Direction |
Attach the claw to install the seat belt anchor cover cap as shown in the illustration.
62514A
16.INSTALL LOWER QUARTER TRIM PANEL LH
|
Install in this Direction |
Attach the clip and claw to install the lower quarter trim panel LH as shown in the illustration.
Connect the front seat outer belt assembly LH with the bolt.
| *1 | Front Door Opening Trim Weatherstrip LH |
Connect the front door opening trim weatherstrip LH in the range shown in the illustration.
62513A
17.INSTALL LOWER QUARTER TRIM PANEL RH
|
Install in this Direction |
Attach the clip and claw to install the lower quarter trim panel RH as shown in the illustration.
Connect the front seat outer belt assembly RH with the bolt.
| *1 | Front Door Opening Trim Weatherstrip RH |
Connect the front door opening trim weatherstrip RH in the range shown in the illustration.
64261C
18.INSTALL UPPER BACK PANEL GARNISH
|
Install in this Direction |
Attach the clip and claw to install the upper back panel garnish as shown in the illustration.
Lower the claw into position to attach it.
67914B
19.INSTALL FRONT DOOR SCUFF PLATE LH
|
Install in this Direction |
Attach the clip and claw to install the front door scuff plate LH as shown in the illustration.
67913B
20.INSTALL FRONT DOOR SCUFF PLATE RH
|
Install in this Direction |
Attach the clip and claw to install the front door scuff plate RH as shown in the illustration.
62212
21.INSTALL FRONT PILLAR GARNISH LH
62211
22.INSTALL FRONT PILLAR GARNISH RH
74610A
23.INSTALL ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)
24.INSTALL FRONT SEAT ASSEMBLY LH
for Manual Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>INSTALLATION
for Bench Seat Type:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Bench Seat Type)>INSTALLATION
25.INSTALL FRONT SEAT ASSEMBLY RH
26.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Airbag System)
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
27.CHECK SRS WARNING LIGHT (w/ Airbag System)