Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
w/ Airbag System:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION
1. TABLE OF BOLT, SCREW, NUT AND CLIP
All bolts, screws and clips relevant to installing and removing the instrument panel are shown along with their alphabetic code in the table below.
2. PRECAUTION (w/ Airbag System)
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Airbag System)
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
55302A
4.REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY
58810J
5.REMOVE CONSOLE BOX ASSEMBLY (w/ Console Box Lid)
58901A
6.REMOVE REAR CONSOLE BOX SUB-ASSEMBLY (w/ Rear Console Box)
58811A
7.REMOVE FRONT CONSOLE BOX (w/o Console Box Lid)
84140
8.REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY
55905J
9.REMOVE CONTROL KNOB SUB-ASSEMBLY (for Manual Cooler System, for Manual Air Conditioning System)
84013A
10.REMOVE INTEGRATION PANEL SUB-ASSEMBLY (for Manual Cooler System, for Manual Air Conditioning System)
55900
11.REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)
55420A
12.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
w/o Audio:
Remove the 4 screws.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull as shown to detach the clip and guide.
Disconnect the connector and remove the center instrument cluster finish panel assembly.
w/ Audio, for Radio Receiver Type:
Remove the 4 screws.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull as shown to detach the clip and guide.
Disconnect the connector and remove the center instrument cluster finish panel assembly.
w/ Audio, for Radio and Display Type:
Remove the 4 screws.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull as shown to detach the clip and guide.
Disconnect the connector and remove the center instrument cluster finish panel assembly.
w/ Audio, for Navigation Receiver Type:
Remove the 4 screws.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull as shown to detach the clip and guide.
Disconnect the connector and remove the center instrument cluster finish panel assembly.
55606
13.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Knee Airbag)
| *a | Screw <A> |
Remove the 2 screws <A>.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull as shown to detach the clip, claw and guide.
Detach the claw and disconnect the DLC3 and remove the No. 1 instrument panel under cover sub-assembly.
73900
14.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)
55045
15.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (w/o Knee Airbag)
| *a | Protective Tape |
| *b | Screw <A> |
Put protective tape around the lower instrument panel finish panel sub-assembly.
Remove the 2 screws <A>.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull as shown to detach the clip and claw.
Detach the claw and disconnect the DLC3 and remove the lower instrument panel finish panel sub-assembly.
55607
16.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
|
Remove in this Direction |
Detach the claw and pull as shown in the illustration.
|
Remove in this Direction |
Pull as shown in the illustration, detach the guide and remove the No. 2 instrument panel under cover sub-assembly.
55550
17.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
|
Remove in this Direction |
Twist the glove door stopper pin as shown in the illustration and remove it.
Use the same procedure for both glove door stopper pins.
Open the glove compartment door assembly, detach the claw and disconnect the glove compartment door stopper sub-assembly.
Pull diagonally to remove the glove compartment door stopper sub-assembly.
|
Remove in this Direction |
Pull as shown in the illustration to detach the hinge and remove the glove compartment door assembly.
55407C
18.REMOVE LOWER INSTRUMENT COVER SUB-ASSEMBLY
| *a | Protective Tape |
Put protective tape around the lower instrument cover sub-assembly.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull as shown to detach the clip and claw.
Disconnect the connector and remove the lower instrument cover sub-assembly.
55054
19.REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY
Detach the claw and remove the glove compartment door stopper sub-assembly.
55303B
20.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
Remove the 7 screws <B>, 2 bolts <C> and screw <D>.
Detach the guide and disconnect the connector.
| *a | Screw <B> | *b | Bolt <C> |
| *c | Screw <D> | *d | Guide |
Detach the claw and guide to disconnect the hood lock control lever sub-assembly and fuel lid lock open lever.
Disconnect the hood lock control cable and fuel lid lock open cable and remove the lower instrument panel sub-assembly.