Home › Vehicle Interior › INTERIOR PANELS / TRIM › UPPER INSTRUMENT PANEL › 2015.06–2016.03
RM3250E _58 Vehicle Interior _037970 INTERIOR PANELS / TRIM _0189524 UPPER INSTRUMENT PANEL A

INTERIOR PANELS / TRIM  UPPER INSTRUMENT PANEL  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



CAUTION:
B414214

w/ Airbag System:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


PROCEDURE

Hide 1. TABLE OF BOLT, SCREW, NUT AND CLIP

HINT:

All bolts, screws and clips relevant to installing and removing the instrument panel are shown along with their alphabetic code in the table below.


B405227E01
5.552,2.281 7.094,2.521 1.542,0.24 10 false mm (in.) (L = Length) 1.146,0.135 1.917,0.333 0.771,0.198 10 false Shape 3.49,0.125 4.26,0.323 0.771,0.198 10 false Shape 5.813,0.125 6.583,0.323 0.771,0.198 10 false Shape 0.146,0.135 0.76,0.333 0.615,0.198 10 false Code 2.448,0.135 3.063,0.333 0.615,0.198 10 false Code 4.781,0.135 5.396,0.333 0.615,0.198 10 false Code 0.188,0.958 0.646,1.156 0.458,0.198 10 false <A> 2.49,0.958 2.948,1.156 0.458,0.198 10 false <B> 4.813,0.927 5.271,1.125 0.458,0.198 10 false <C> 0.177,1.885 0.635,2.083 0.458,0.198 10 false <D> 6.49,0.646 6.844,0.844 0.354,0.198 10 false φ 8 6.479,0.854 7.073,1.052 0.594,0.198 10 false (0.315) 6.5,1.083 7.01,1.281 0.51,0.198 10 false L=18 6.479,1.271 7.063,1.469 0.583,0.198 10 false (0.709) 1.76,1.563 2.115,1.76 0.354,0.198 10 false φ 5 1.75,1.771 2.823,1.969 1.073,0.198 10 false (0.197) 1.76,2.021 2.375,2.219 0.615,0.198 10 false L=14 1.74,2.208 2.813,2.406 1.073,0.198 10 false (0.551)

Hide 2. PRECAUTION (w/ Airbag System)

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Airbag System)

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 45100 4.REMOVE STEERING WHEEL ASSEMBLY

Hide 55410C 5.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

a.
B412949C01
0.927,0.625 0.615,0.323 true 0.479,0.208 0.698,0.365 0.219,0.156 10 true *a 1,1.021 1.198,1.177 0.198,0.156 10 true *b 1.854,0.74 2.052,0.896 0.198,0.156 10 true *b
*a Protective Tape
*b Clip <A>


Put protective tape around the instrument cluster finish panel assembly.


b.

Remove the 2 clips <A>.

NOTICE:

Take care when turning the screw portion of the clip.



c.
B412950C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw, clip and guide and remove the instrument cluster finish panel assembly.


Hide 83100 6.REMOVE COMBINATION METER ASSEMBLY

Hide 55650 7.REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B412952C01
0.708,0.552 0.427,0.344 true 0.26,0.188 0.479,0.344 0.219,0.156 10 true *a
*a Protective Tape


Put protective tape around the No. 1 instrument panel register assembly.


b.
B412953C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the clip and remove the No. 1 instrument panel register assembly.


Hide 62112 9.REMOVE COWL SIDE TRIM BOARD LH

B412955C01
2.708,0.708 2.917,0.865 0.208,0.156 10 true *a
*a Cap Nut
V113146

Place Hands Here
V113147

Remove in this Direction


a.

Remove the cap nut.


b.

Place your hands at the position shown in the illustration and pull as shown to detach the clip and remove the cowl side trim board LH.


Hide 55318C 10.REMOVE INSTRUMENT SIDE PANEL LH

a.
B412957C01
2.24,1.073 2.458,1.229 0.219,0.156 10 true *1
*1 Front Door Opening Trim Weatherstrip LH


Disconnect the front door opening trim weatherstrip LH in the range shown in the illustration.


b.
B412958C01
1.427,1.448 2.042,1.635 true 2.073,1.583 2.281,1.74 0.208,0.156 10 true *a
*a Protective Tape


Put protective tape around the instrument side panel LH.


c.
B412959C01
0,0 0,0 false
V113146

Insert Moulding Remover A Here
V113147

Remove in this Direction


Insert moulding remover A at the position shown in the illustration and pull as shown to detach the claw, clip and guide and remove the instrument side panel LH.


Hide 55470 11.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY

a.

Put protective tape around the instrument cluster finish panel garnish assembly.

B412962C01
4.698,1.208 5.135,0.594 true 5.073,0.448 5.292,0.604 0.219,0.156 10 true *a
*a Protective Tape - -



b.
B412963C01
0,0 0,0 false
V113146

Insert Moulding Remover A Here
V113147

Remove in this Direction


Insert moulding remover A at the position shown in the illustration and pull as shown to detach the clip.


c.

Place your hands in the gap created during the above procedure and pull as shown in the illustration to detach the clip and remove the instrument cluster finish panel garnish assembly.

B412964C01
0,0 0,0 false
V113147

Remove in this Direction
V100135

Order of Removal



Hide 55041B 12.REMOVE NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY

a.
B412966C01
0.438,0.75 0.26,0.302 true 0.125,0.135 0.333,0.292 0.208,0.156 10 true *a
*a Protective Tape


Put protective tape around the No. 1 instrument panel box door sub-assembly.


b.

Open the lid of the No. 1 instrument panel box door sub-assembly.


c.
B412967C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the clip and guide and remove the No. 1 instrument panel box door sub-assembly.


Hide 55660 13.REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B412969C01
2.396,1.208 2.875,1.344 true 2.885,1.281 3.104,1.438 0.219,0.156 10 true *a
*a Protective Tape


Put protective tape around the No. 2 instrument panel register assembly.


b.
B412970C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the clip and remove the No. 2 instrument panel register assembly.


Hide 62111C 15.REMOVE COWL SIDE TRIM BOARD RH

a.
B412972C01
0.792,0.823 1.01,0.979 0.219,0.156 10 true *a
*a Cap Nut
V113146

Place Hands Here
V113147

Remove in this Direction


Remove the cap nut.


b.

Place your hands at the position shown in the illustration and pull as shown to detach the clip and remove the cowl side trim board RH.


Hide 55317A 16.REMOVE INSTRUMENT SIDE PANEL RH

a.
B412974C01
0.958,1.042 1.167,1.198 0.208,0.156 10 true *1
*1 Front Door Opening Trim Weatherstrip RH


Disconnect the front door opening trim weatherstrip RH in the range shown in the illustration.


b.
B412975C01
1.104,1.865 1.594,1.573 true 0.917,1.802 1.146,1.958 0.229,0.156 10 true *a
*a Protective Tape


Put protective tape around the instrument side panel RH.


c.
B412976C01
0,0 0,0 false
V113146

Insert Moulding Remover A Here
V113147

Remove in this Direction


Insert moulding remover A at the position shown in the illustration and pull as shown to detach the claw, clip and guide and remove the instrument side panel RH.


d.

w/ Airbag Cut Off Switch:

Disconnect the connector and remove the instrument side panel RH.


Hide 74610A 17.REMOVE ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)

HINT:

Use the same procedure for both pillar assist grip assemblies.


a.
B404468C01
0.833,1.594 1.156,1.063 true 0.708,1.594 0.927,1.75 0.219,0.156 10 true *a
*a Protective Tape


Put protective tape around the assist grip covers.


b.
B404469C01
0.74,0.979 1.208,1.094 true 0.583,0.875 0.781,1.031 0.198,0.156 10 true *a
*a Protective Tape
V113146

Insert Thin-bladed Screwdriver Here


Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and open the assist grip covers.

HINT:

Tape the thin-bladed screwdriver tip before use.



c.
B404470

Remove the 2 bolts and assist grip sub-assembly.


Hide 62212 18.REMOVE FRONT PILLAR GARNISH LH

a.
B412983C01
2.531,1.531 2.854,1.719 true 2.865,1.688 3.083,1.844 0.219,0.156 10 true *a
*a Protective Tape


Put protective tape around the front pillar garnish LH.


b.
B412984C01
0.427,1.25 0.74,1.406 0.313,0.156 10 false *1
*1 Front Door Opening Trim Weatherstrip LH


Disconnect the front door opening trim weatherstrip LH in the range shown in the illustration.


c.
B412985C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Place your hands at the position shown in the illustration and pull as shown to detach the clip and guide and remove the front pillar garnish LH.


d.
B405232C01
0.948,2.094 1.313,1.75 true 2.156,1.917 2.594,1.677 true 1.667,1.198 2.021,0.885 true 2.583,1.552 2.813,1.708 0.229,0.156 10 true *a 1.979,0.771 2.188,0.927 0.208,0.156 10 true *b 0.802,2.063 1.01,2.219 0.208,0.156 10 true *b
*a Protective Cover
*b Adhesive Tape


w/ Curtain Shield Airbag:

Protect the curtain shield airbag assembly LH.

i.

Completely cover the curtain shield airbag assembly LH with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

NOTICE:

Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.




Hide 62211 19.REMOVE FRONT PILLAR GARNISH RH

a.
B412979C01
0.719,1.688 1.156,1.396 true 0.531,1.635 0.771,1.792 0.24,0.156 10 true *a
*a Protective Tape


Put protective tape around the front pillar garnish RH.


b.
B412980C01
2.781,1.24 3,1.406 0.219,0.167 10 false *1
*1 Front Door Opening Trim Weatherstrip RH


Disconnect the front door opening trim weatherstrip RH in the range shown in the illustration.


c.
B412981C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Place your hands at the position shown in the illustration and pull as shown to detach the clip and guide and remove the front pillar garnish RH.


d.
B405233C01
1.333,1.583 0.885,1.083 true 2.167,2.385 1.719,1.885 true 2.677,2.198 2.219,1.792 true 2.188,2.427 2.5,2.583 0.313,0.156 10 false *a 2.719,2.198 3.031,2.354 0.313,0.156 10 false *b 0.74,0.948 0.958,1.104 0.219,0.156 10 true *b
*a Protective Cover
*b Adhesive Tape


w/ Curtain Shield Airbag:

Protect the curtain shield airbag assembly RH.

i.

Completely cover the curtain shield airbag assembly RH with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

NOTICE:

Cover the curtain shield airbag assembly RH with a protective cover as soon as the front pillar garnish RH is removed.




Hide 55302A 20.REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY

a.

w/ Front Passenger Airbag:

i.
B339324C07
0.74,0.917 0.99,0.427 true 0.969,0.281 1.281,0.438 0.313,0.156 10 false *a
*a Lock Slider


Pull and slide the lock slider as shown to release the connector lock and disconnect the passenger airbag connector.

NOTICE:

When handling the passenger airbag connector, take care not to damage the airbag wire harness.




b.

Disconnect the connector and detach the clamp.


c.

Remove the 2 clips <B>.


d.

w/ Front Passenger Airbag:

i.

Remove the passenger airbag installation bolt <C>.

B412987C03
0.344,2.75 0.594,2.906 0.25,0.156 10 true *A 1.896,3.354 2.115,3.51 0.219,0.156 10 true *B 1.031,3.51 1.24,3.667 0.208,0.156 10 true *b 0.635,0.271 0.833,0.427 0.198,0.156 10 true *c 5,3.552 5.208,3.708 0.208,0.156 10 true *d 0.844,3.281 1.052,3.438 0.208,0.156 10 true *b 6.708,0.594 6.906,0.75 0.198,0.156 10 true *c 2.271,3.396 2.479,3.552 0.208,0.156 10 true *b 4.667,2.76 4.917,2.917 0.25,0.156 10 true *B 1.906,3.521 2.125,3.677 0.219,0.156 10 true *a
*A w/ Smart Entry and Start System *B w/ Front Passenger Airbag
*a Passenger Airbag Connector *b Connector
*c Clip <B> *d Passenger Airbag Installation Bolt <C>




e.

Place your hands at the position shown in the illustration and pull as shown to detach the clip.


f.

Detach the guide and remove the upper instrument panel sub-assembly.

B412988C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction