Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM
RM3250E _51 Engine / Hybrid System _037972 1GD-FTV ENGINE CONTROL _0189556 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P0488  Exhaust Gas Recirculation Throttle Position Control Range / Performance  


DESCRIPTION

The ECM opens and closes the throttle valve using a DC motor type actuator. Due to the opening and closing of the valve, the exhaust gas recirculation volume can be properly controlled. Also, engine vibration and noise will be reduced by closing the valve when the engine is stopped.

Although the DTC title says "Exhaust Gas Recirculation Throttle Position Control Range / Performance", this DTC indicates that the throttle valve is malfunctioning.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance The throttle actuator activation duty is more than specified value for 60 seconds (1 trip detection logic).
·

Throttle valve stuck

·

Throttle valve does not move smoothly

·

Open or short in throttle actuator circuit

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0488
·

Target Throttle Position

·

Actual Throttle Position

·

Throttle Motor DUTY

·

Throttle Close Learning Val.



Reference
Condition Throttle Valve Position
Moment when accelerator pedal is depressed further or released at 3000 rpm Throttle valve opening angle varies smoothly

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0488 Perform the following repeatedly for 1 minute:
gradually raise the engine speed to 3000 rpm from idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state.

MONITOR DESCRIPTION

The ECM opens and closes the throttle valve by adjusting the current flowing to the DC motor with a duty ratio. If the throttle valve does not move smoothly or is stuck, the duty ratio used during valve movement control increases or decreases greatly. The ECM will determine that the throttle valve is malfunctioning and illuminate the MIL.

A206049E06
4.573,2.135 4.708,1.792 false 4.563,2.896 4.698,2.563 false 4.563,3.646 4.698,3.302 false 4.698,4.479 4.594,4.188 false 5.302,5.24 5.125,5.031 false 3.448,5.198 3.219,5.021 false 0.25,5.438 1.646,5.802 1.396,0.365 10 Duty Ratio Malfunction Counter 0.094,0.031 1.875,0.24 1.781,0.208 10 Malfunction Detection: 0.25,1.25 1.656,1.615 1.406,0.365 10 Throttle Valve Target Opening Angle 0.25,2.708 1.729,3.104 1.479,0.396 10 Throttle Valve Actual Opening Angle 0.906,4.125 1.646,4.344 0.74,0.219 10 Duty Ratio 4.75,1.719 5.344,1.917 0.594,0.198 10 Normal 4.75,2.479 5.5,2.677 0.75,0.198 10 Abnormal 4.75,4.375 5.344,4.573 0.594,0.198 10 Normal 4.75,3.219 5.5,3.417 0.75,0.198 10 Abnormal 5.906,0.594 6.354,0.792 0.448,0.198 10 Open 5.906,1.354 6.385,1.552 0.479,0.198 10 Close 5.906,2.063 6.354,2.26 0.448,0.198 10 Open 5.906,2.823 6.385,3.021 0.479,0.198 10 Close 5.906,3.573 6.417,3.781 0.51,0.208 10 100% 5.906,4.333 6.25,4.531 0.344,0.198 10 0% 3.49,5.104 4.521,5.313 1.031,0.208 10 Stores P0488 5.302,5.24 6.094,5.448 0.792,0.208 10 Threshold 3.469,6.271 3.875,6.479 0.406,0.208 10 Time

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When cleaning the diesel throttle body assembly, use a piece of cloth soaked with cleaning solvent. Spraying solvent directly onto these parts or soaking the parts in solvent may damage the parts.

·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (DIESEL THROTTLE TARGET ANGLE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Diesel Throttle Target Angle / Primary / Actual Throttle Position.

Powertrain > Engine and ECT > Active Test
Active Test Display
Diesel Throttle Target Angle
Data List Display
Actual Throttle Position
50004 234 240 830

d.

When changing the Active Test continuously value to 10, 30, 60, 90, 60, 30 and 10%, check that Actual Throttle Position smoothly changes to the set opening angle.

OK:

Value smoothly changes to set opening angle.



Result:
Proceed to
OK
NG



OK

2.REMOVE DEPOSIT (DIESEL THROTTLE BODY ASSEMBLY)

NG

8.REMOVE DEPOSIT (DIESEL THROTTLE BODY ASSEMBLY)
2.REMOVE DEPOSIT (DIESEL THROTTLE BODY ASSEMBLY)
a.

Visually check for deposits in the diesel throttle body assembly. If there are deposits, clean the diesel throttle body assembly.

NOTICE:
·

When cleaning the diesel throttle body assembly, use a piece of cloth soaked with cleaning solvent. Spraying solvent directly onto these parts or soaking the parts in solvent may damage the parts.

·

Extreme care must be taken to prevent the removed deposits from falling into the engine unit during cleaning.




Result:
Proceed to
NEXT



NEXT

3.INSPECT DIESEL THROTTLE BODY ASSEMBLY (THROTTLE VALVE MOVEMENT)
3.INSPECT DIESEL THROTTLE BODY ASSEMBLY (THROTTLE VALVE MOVEMENT)
a.

Using your finger, move the throttle valve from the fully open position to the fully closed position and check that it moves smoothly.

OK:

Throttle valve moves smoothly.


NOTICE:

Take care not to damage the throttle valve or valve housing.



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0488)

NG

7.REPLACE DIESEL THROTTLE BODY ASSEMBLY
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0488)
a.

Start the engine and warm it up.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Take a snapshot with the GTS.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Diesel Throttle Target Angle / Primary / Actual Throttle Position.

Powertrain > Engine and ECT > Active Test
Active Test Display
Diesel Throttle Target Angle
Data List Display
Actual Throttle Position
50004 234 240 830
HINT:

The movement of the throttle valve can be determined by performing the following inspection.



f.

When changing the Active Test value continuously to 10, 30, 60, 90, 60, 30 and 10%, check that Actual Throttle Position smoothly changes to the set opening angle.

OK:

Value smoothly changes to set opening angle.



g.

Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from an idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
OK:

DTC is not output.



Result:
Proceed to
OK
NG



OK

END

NG

5.REPLACE ECM
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0488)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0488)
a.

Start the engine and warm it up.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Take a snapshot with the GTS.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Diesel Throttle Target Angle / Primary / Actual Throttle Position.

Powertrain > Engine and ECT > Active Test
Active Test Display
Diesel Throttle Target Angle
Data List Display
Actual Throttle Position
50004 234 240 830
HINT:

The movement of the throttle valve can be determined by performing the following inspection.



f.

When changing the Active Test value continuously to 10, 30, 60, 90, 60, 30 and 10%, check that Actual Throttle Position smoothly changes to the set opening angle.

OK:

Value smoothly changes to set opening angle.



g.

Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from an idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Confirm that the DTC is not output.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

7.REPLACE DIESEL THROTTLE BODY ASSEMBLY
a.

Replace the diesel throttle body assembly.

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>DIESEL THROTTLE BODY>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0488)
8.REMOVE DEPOSIT (DIESEL THROTTLE BODY ASSEMBLY)
a.

Visually check for deposits in the diesel throttle body assembly. If there are deposits, clean the diesel throttle body assembly.

NOTICE:
·

When cleaning the diesel throttle body assembly, use a piece of cloth soaked with cleaning solvent. Spraying solvent directly onto these parts or soaking the parts in solvent may damage the parts.

·

Extreme care must be taken to prevent the removed deposits from falling into the engine unit during cleaning.




Result:
Proceed to
NEXT



NEXT

9.INSPECT DIESEL THROTTLE BODY ASSEMBLY (THROTTLE VALVE MOVEMENT)
9.INSPECT DIESEL THROTTLE BODY ASSEMBLY (THROTTLE VALVE MOVEMENT)
a.

Using your finger, move the throttle valve from the fully open position to the fully closed position and check that it moves smoothly.

OK:

Throttle valve moves smoothly.


NOTICE:

Take care not to damage the throttle valve or valve housing.



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (DIESEL THROTTLE BODY ASSEMBLY - ECM)

NG

7.REPLACE DIESEL THROTTLE BODY ASSEMBLY
10.CHECK HARNESS AND CONNECTOR (DIESEL THROTTLE BODY ASSEMBLY - ECM)
a.

Disconnect the diesel throttle body assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y1-5 (VC) - C59-29 (VCVL) Always Below 1 Ω
Y1-6 (VTA) - C59-21 (VLU) Always Below 1 Ω
Y1-3 (E2) - C59-20 (EVLU) Always Below 1 Ω
Y1-2 (M+) - C60-6 (M+) Always Below 1 Ω
Y1-1 (M-) - C60-5 (M-) Always Below 1 Ω
Y1-5 (VC) or C59-29 (VCVL) - Body ground and other terminals Always 10 kΩ or higher
Y1-6 (VTA) or C59-21 (VLU) - Body ground and other terminals Always 10 kΩ or higher
Y1-3 (E2) or C59-20 (EVLU) - Body ground and other terminals Always 10 kΩ or higher
Y1-2 (M+) or C60-6 (M+) - Body ground and other terminals Always 10 kΩ or higher
Y1-1 (M-) or C60-5 (M-) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the diesel throttle body assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

7.REPLACE DIESEL THROTTLE BODY ASSEMBLY

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0488)