While the engine is being cranked, current flows from terminal STAR of the certification ECU (smart key ECU assembly) to the park/neutral position switch assembly*1 or clutch start switch*2 and to terminal STA of the ECM (STA signal).
*1: for Automatic Transmission
*2: for Manual Transmission
Refer to DTC P0617 for w/ Smart Entry and Start System.
Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM>P0617
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).
Check if the engine can be cranked.
| Result | Proceed to |
|---|---|
| Engine cannot be cranked | A |
| Engine can be cranked | B |
A
B
Connect the GTS to DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Check the result when the ignition switch is ON and the engine starts.
| Switch Condition | Starter Signal |
|---|---|
| ON | OFF |
| START | ON |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ST NO. 1 relay.
Click hereEngine / Hybrid System>1GD-FTV STARTING>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the starter assembly.
for 2.0 kW Type
Click hereEngine / Hybrid System>1GD-FTV STARTING>STARTER(for 2.0 kW Type)>INSPECTION
for 2.2 kW Type
Click hereEngine / Hybrid System>1GD-FTV STARTING>STARTER(for 2.2 kW Type)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 2.0 kW Type
Click hereEngine / Hybrid System>1GD-FTV STARTING>STARTER(for 2.0 kW Type)>REMOVAL
for 2.2 kW Type
Click hereEngine / Hybrid System>1GD-FTV STARTING>STARTER(for 2.2 kW Type)>REMOVAL
Remove the ST NO. 1 relay from the engine room relay block and junction block.
Disconnect the starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (ST NO. 1 relay terminal holder) - C32-1 (ST) | Always | Below 1 Ω |
| 3 (ST NO. 1 relay terminal holder) or C32-1 (ST) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the starter assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D3-1 (B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay from the engine room relay block and junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (ST NO. 1 relay terminal holder) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for Automatic Transmission
*2: for Manual Transmission
Remove the ST NO. 1 relay from the engine room relay block and junction block.
Disconnect the park/neutral position switch assembly connector.*1
Disconnect the clutch start switch connector.*2
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C24-5 (L)*1 - 2 (ST NO. 1 relay terminal holder) | Always | Below 1 Ω |
| B2-1*2 - 2 (ST NO. 1 relay terminal holder) | Always | Below 1 Ω |
| G70-37 (STA) - 2 (ST NO. 1 relay terminal holder) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay from the engine room relay block and junction block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (ST NO. 1 relay terminal holder) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for Automatic Transmission
*2: for Manual Transmission
Inspect the park/neutral position switch assembly.*1
Inspect the clutch start switch.*2
| Proceed to |
|---|
| OK |
| NG (for Automatic Transmission) |
| NG (for Manual Transmission) |
OK
NG (for Automatic Transmission)
NG (for Manual Transmission)
*1: for Automatic Transmission
*2: for Manual Transmission
Disconnect the park/neutral position switch assembly connector.*1
Disconnect the clutch start switch connector.*2
Disconnect the ECM connector.
Remove the ST NO. 1 relay from the engine room relay block and junction block.
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C24-5 (L) - G85-22 (STA)*1 | Always | Below 1 Ω |
| B2-1 - G85-22 (STA)*2 | Always | Below 1 Ω |
| C24-5 (L) or G85-22 (STA) or 2 (ST NO. 1 relay terminal holder) or G70-37 (STA) - Body ground and other terminals*1 | Always | 10 kΩ or higher |
| B2-1 or G85-22 (STA) or 2 (ST NO. 1 relay terminal holder) or G70-37 (STA) - Body ground and other terminals*2 | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for Automatic Transmission
*2: for Manual Transmission
Disconnect the park/neutral position switch assembly connector.*1
Disconnect the clutch start switch connector.*2
Disconnect the certification ECU (smart key ECU assembly) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G70-16 (STAR) - C24-4 (B)*1 | Always | Below 1 Ω |
| G70-16 (STAR) - B2-2*2 | Always | Below 1 Ω |
| G70-16 (STAR) - G85-11 (NSW) | Always | Below 1 Ω |
| G70-16 (STAR) or C24-4 (B) or G85-11 (NSW) - Body ground and other terminals*1 | Always | 10 kΩ or higher |
| G70-16 (STAR) or B2-2 or G85-11 (NSW) - Body ground and other terminals*2 | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Check the result when the ignition switch is ON and the engine starts.
| Switch Condition | Starter Signal |
|---|---|
| ON | OFF |
| START | ON |
| Proceed to |
|---|
| OK |
| NG |
OK
NG