Home › Brake › BRAKE SYSTEM (OTHER) › LOAD SENSING PROPORTIONING VALVE(w/o ABS)
RM3250E _54 Brake _038045 BRAKE SYSTEM (OTHER) _0189595 LOAD SENSING PROPORTIONING VALVE(w/o ABS) A

BRAKE SYSTEM (OTHER)  LOAD SENSING PROPORTIONING VALVE(w/o ABS)  INSTALLATION  


PROCEDURE

Hide 04477 1.INSTALL LOAD SENSING SPRING BUSH & BOOT KIT

a.

Install the load sensing valve boot and load sensing spring boot to the load sensing spring assembly.


b.

Install both dust seals, No. 1 load sensing spring bushes and No. 2 load sensing spring bushes to the load sensing spring assembly.

NOTICE:
·

Apply lithium soap base glycol grease to all contact surfaces.

·

Make sure the valve side and shackle side of the spring are installed properly.




Hide 47935 2.INSTALL NO. 1 LOAD SENSING SPRING SHACKLE AND NO. 2 LOAD SENSING SPRING SHACKLE

a.

Install the adjusting nut, plate washer and No. 2 load sensing spring shackle to the No. 1 load sensing spring shackle.


b.

Tighten the lock nut.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


c.

Install the No. 1 load sensing spring shackle (with the No. 2 load sensing spring shackle) to the load sensing spring assembly.


d.

Install the 2 plate washers and spring washer with the bolt and nut.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 3.INSTALL LOAD SENSING SPRING ASSEMBLY

a.

Using pliers, install the load sensing spring assembly to the load sensing valve body with the clip.


Hide 47931 4.INSTALL LOAD SENSING VALVE BRACKET

a.

Install the load sensing valve set plate to the load sensing valve bracket.


b.

Install the load sensing valve bracket with the 3 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


c.

Install the load sensing valve bracket to the load sensing valve assembly with the nut and bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 47352 5.INSTALL REAR FLEXIBLE HOSE BRACKET

a.

Install the rear flexible hose bracket and load sensing valve set plate to the 2 spring washers with the 2 nuts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


b.

Install a new clip.


c.
A329093C03
1.719,0.542 2.031,0.698 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the rear No. 9 brake tube to the rear brake flexible hose.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




d.
A329093C03
1.719,0.542 2.031,0.698 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the 3 brake lines to the load sensing valve body.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)



NOTICE:
·

Do not damage or deform the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




Hide 6.CONNECT NO. 2 LOAD SENSING SPRING SHACKLE

a.

Connect the No. 2 shackle to the rear differential.


b.

Install the bolt, collar and 2 load sensing valve bushes.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


Hide 8.BLEED CLUTCH LINE (for Manual Transmission)

Hide 47900 9.CHECK LOAD SENSING PROPORTIONING VALVE ASSEMBLY

Hide 47900 10.ADJUST LOAD SENSING PROPORTIONING VALVE ASSEMBLY