Home › Engine / Hybrid System › 2KD-FTV FUEL › FUEL SUPPLY PUMP
RM3250E _51 Engine / Hybrid System _038015 2KD-FTV FUEL _0189699 FUEL SUPPLY PUMP A

2KD-FTV FUEL  FUEL SUPPLY PUMP  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

No. 3 injection pipe sub-assembly

·

No. 4 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing Gear Case Assembly


Fuel inlet pipe sub-assembly

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.



PROCEDURE

Hide 22100 1.INSTALL FUEL SUPPLY PUMP ASSEMBLY

NOTICE:
A347309

Do not hold the supply pump assembly by the parts indicated by the arrows in the illustration.


a.
A070715

Check that the injection gear in the timing gear case assembly moves back and forth smoothly.


b.

Install a new O-ring to the fuel supply pump assembly.


c.

Apply a light coat of engine oil to the O-ring.


d.
A060835C01
0.813,0.792 1.396,0.125 1.396,0.125 1.604,0.125 true 2.219,1.458 2.219,0.146 2.219,0.146 2.427,0.146 true 1.656,0.031 1.969,0.188 0.313,0.156 10 false *a 2.479,0.063 2.792,0.219 0.313,0.156 10 false *b
*a Groove
*b Set Key


Align the groove of the injection gear with the set key on the fuel supply pump drive shaft.


e.

Install the fuel supply pump assembly with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


f.

Set a new O-ring before tightening the set nut.


g.
A301691C01
0.448,1.479 1.667,1.479 true 0.75,1.469 0.75,1.073 0.75,1.073 1.219,1.073 true 0.156,1.396 0.615,1.594 0.458,0.198 10 false SST

Using SST, hold the crankshaft pulley and install the set nut.

SST
09213-58014  (91551-80840)
09330-00021  

Torque:
63.7 N*m (650 kgf*cm, 47 ft.*lbf)


h.

Install the pump drive shaft pulley and No. 2 camshaft timing pulley flange with the 4 bolts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


i.
A071144

Move the pump drive shaft pulley back and forth to check the thrust clearance of the fuel supply pump drive shaft.

Standard thrust clearance (reference):

0.15 to 0.55 mm (0.00590 to 0.0217 in.)


If there is no clearance, disassemble and reassemble the fuel supply pump assembly and pump drive shaft pulley. Then repeat the step above.


j.

Connect the connector to the fuel temperature sensor.


k.

Connect the connector to the suction control valve.


l.

Connect the fuel hose and No. 1 fuel hose to the fuel supply pump assembly, and slide the 2 clamps to secure the hoses.


Hide 23804C 2.INSTALL FUEL INLET PIPE SUB-ASSEMBLY

a.

Temporarily install the fuel inlet pipe sub-assembly with the union nuts.

NOTICE:
·

When replacing the fuel supply pump assembly, it is necessary to replace the fuel inlet pipe sub-assembly with a new one.

·

Keep the fuel inlet pipe sub-assembly free of foreign matter.




b.
A329093C06
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the fuel inlet pipe sub-assembly union nut on the common rail assembly side.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




c.
A329093C06
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the fuel inlet pipe sub-assembly union nut on the fuel supply pump assembly side.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




Hide 11452 3.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 16400 5.INSTALL RADIATOR ASSEMBLY

Hide 6.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 9.PERFORM FUEL SUPPLY PUMP INITIALIZATION