Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM(w/ DPF)
RM3250E _51 Engine / Hybrid System _037972 1GD-FTV ENGINE CONTROL _0190004 ECD SYSTEM(w/ DPF) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0107  Manifold Absolute Pressure / Barometric Pressure Circuit Low Input  P0108  Manifold Absolute Pressure / Barometric Pressure Circuit High Input  


DESCRIPTION

A208461E08
0.417,0.406 0.708,0.646 0.292,0.24 10 false V 0.219,0.833 0.635,1.073 0.417,0.24 10 false 3.586 0.219,1.875 0.76,2.135 0.542,0.26 10 false 0.386 1.031,2.323 1.292,2.51 0.26,0.188 10 false 40 2.333,2.323 2.667,2.552 0.333,0.229 10 false 320 0.979,2.667 1.292,2.833 0.313,0.167 10 false 300 0.938,2.823 1.344,3.052 0.406,0.229 10 false (11.8) 2.281,2.833 2.719,3.052 0.438,0.219 10 false (94.5) 2.854,2.833 3.354,3.042 0.5,0.208 10 false (in.Hg) 2.854,2.531 3.354,2.75 0.5,0.219 10 false mmHg 2.875,2.115 3.229,2.302 0.354,0.188 10 false kPa 2.844,2.26 3.271,2.479 0.427,0.219 10 false (abs) 2.292,2.677 2.646,2.896 0.354,0.219 10 false 2400 1.333,3.063 2.219,3.323 0.885,0.26 10 false Air Pressure

The manifold absolute pressure sensor detects the intake manifold pressure. The ECM determines the basic injection volume and injection advance timing based on the voltage output by the manifold absolute pressure sensor.

The manifold absolute pressure sensor monitors the absolute pressure inside the intake manifold (default is 0 kPa [0 mmHg, 0 in.Hg]).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0107 Manifold Absolute Pressure / Barometric Pressure Circuit Low Input After the engine is started, condition (a) continues for more than 0.5 seconds (1 trip detection logic):
(a) Manifold absolute pressure sensor voltage is 0.1 V or less.
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


Comes on DTC stored
P0108 Manifold Absolute Pressure / Barometric Pressure Circuit High Input After the engine is started, condition (a) continues for more than 0.5 seconds (1 trip detection logic):
(a) Manifold absolute pressure sensor voltage is 4.8 V or higher.
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0107
·

MAP

·

Atmosphere Pressure


P0108

HINT:
·

If DTC P0107 and/or P0108 is stored, the following symptoms may appear:

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power


·

When DTC P0107 or P0108 is stored, check the intake manifold pressure by entering the following menus: Powertrain / Engine and ECT / Data List / MAP.

Reference
GTS Displayed Malfunction
22 kPa (165 mmHg, 6.5 in.Hg)
·

Open in VC circuit

·

Open in PIM circuit

·

Short in PIM circuit


320 kPa (2400 mmHg, 94.5 in.Hg) or higher
·

Open in E circuit





CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0107 2 seconds after engine is started, race engine for 1 second
P0108

WIRING DIAGRAM

A348539E03
0.51,2.229 2.719,2.427 2.208,0.198 10 false Manifold Absolute Pressure Sensor 0.51,2.042 0.969,2.24 0.458,0.198 10 false C89 1.521,0.469 1.979,0.667 0.458,0.198 10 false VC 1.469,1.042 1.927,1.24 0.458,0.198 10 false PIM 1.615,1.583 2.073,1.781 0.458,0.198 10 false E 5.656,0.469 6.313,0.667 0.656,0.198 10 false VCPM 5.667,1.021 6.125,1.219 0.458,0.198 10 false PIM 5.646,1.583 6.104,1.781 0.458,0.198 10 false EPIM 1.833,0.573 2.292,0.771 0.458,0.198 10 false 3 1.833,1.156 2.292,1.354 0.458,0.198 10 false 2 1.823,1.698 2.281,1.896 0.458,0.198 10 false 1 5.406,0.583 5.667,0.792 0.26,0.208 10 false 28 5.385,1.146 5.875,1.333 0.49,0.188 10 false 18 5.396,1.698 5.677,1.896 0.281,0.198 10 false 19 5.99,2.24 6.521,2.438 0.531,0.198 10 false ECM 5.99,2.052 6.448,2.25 0.458,0.198 10 false C57

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (MAP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.

Powertrain > Engine and ECT > Data List
Tester Display
MAP
50003 234 4

d.

Read the value.

OK:

Same as the actual atmospheric pressure.


HINT:
·

Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather (high atmospheric pressure, low atmospheric pressure).

·

Also, check "Atmosphere Pressure" in the Data List.




Result:
Proceed to
OK
NG



OK

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

2.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)
2.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)
a.
A204467C30
0.677,1.135 1.042,1.385 0.365,0.25 1.24,1.75 1.49,1.292 true 2.177,1.729 1.948,1.292 true 1.708,1.729 1.688,1.281 true 0.167,0.208 0.479,0.406 0.313,0.198 10 false *a 0.729,1.177 1.052,1.375 0.323,0.198 10 false C89 1.177,1.75 1.479,2 0.302,0.25 10 false E 2.198,1.74 2.51,1.938 0.313,0.198 10 false VC 1.615,1.76 2,1.969 0.385,0.208 10 false PIM
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)


Disconnect the manifold absolute pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C89-3 (VC) - C89-1 (E) Ignition switch ON 4.5 to 5.5 V



c.

Reconnect the manifold absolute pressure sensor connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT MANIFOLD ABSOLUTE PRESSURE SENSOR (PIM VOLTAGE)

NG

7.CHECK ECM (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)
3.INSPECT MANIFOLD ABSOLUTE PRESSURE SENSOR (PIM VOLTAGE)
a.
A257437C65
0.25,0.875 0.656,1.115 0.406,0.24 0.323,2.292 0.521,1.656 true 1,2.281 0.573,1.656 true 0.146,0.146 0.458,0.344 0.313,0.198 10 false *a 0.333,0.917 0.792,1.188 0.458,0.271 10 false C57 0.115,2.302 0.885,2.552 0.771,0.25 10 false 19 (EPIM) 1.01,2.302 1.938,2.51 0.927,0.208 10 false 18 (PIM)
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C57-18 (PIM) - C57-19 (EPIM) Ignition switch ON 0.8 to 1.5 V



Result:
Proceed to
OK
NG



OK

8.REPLACE ECM

NG

4.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
4.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C89-2 (PIM) - C57-18 (PIM) Always Below 1 Ω
C89-1 (E) - C57-19 (EPIM) Always Below 1 Ω
C89-2 (PIM) or C57-18 (PIM) - Body ground and other terminals Always 10 kΩ or higher
C89-1 (E) or C57-19 (EPIM) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the manifold absolute pressure sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.CHECK ECM (CHECK RESISTANCE)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK ECM (CHECK RESISTANCE)
a.

Disconnect the manifold absolute pressure sensor connector.


b.
A204467C30
0.677,1.135 1.042,1.385 0.365,0.25 1.24,1.75 1.49,1.292 true 2.177,1.729 1.948,1.292 true 1.708,1.729 1.688,1.281 true 0.167,0.208 0.479,0.406 0.313,0.198 10 false *a 0.729,1.177 1.052,1.375 0.323,0.198 10 false C89 1.177,1.75 1.479,2 0.302,0.25 10 false E 2.198,1.74 2.51,1.938 0.313,0.198 10 false VC 1.615,1.76 2,1.969 0.385,0.208 10 false PIM
*a Front view of wire harness connector
(to Absolute Pressure Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
C89-3 (VC) - C89-2 (PIM) Ignition switch off No short or open circuit
C89-2 (PIM) - C89-1 (E)



c.

Reconnect the manifold absolute pressure sensor connector.


Result:
Proceed to
OK
NG



OK

6.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

8.REPLACE ECM
6.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Replace the manifold absolute pressure sensor.

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK ECM (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.
A257437C66
0.25,0.875 0.646,1.125 0.396,0.25 0.938,2.313 0.573,1.698 true 0.24,2.333 0.521,1.646 true 0.146,0.146 0.458,0.344 0.313,0.198 10 false *a 0.313,0.927 0.688,1.135 0.375,0.208 10 false C57 0.844,2.365 1.875,2.573 1.031,0.208 10 false 28 (VCPM) 0.073,2.365 0.854,2.563 0.781,0.198 10 false 19 (EPIM)
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C57-28 (VCPM) - C57-19 (EPIM) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



NG

8.REPLACE ECM

OK

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the GTS off.


e.

Turn the ignition switch to ON for 3 seconds and turn the GTS on.


f.

After the engine is started for 2 seconds, race the engine for 1 second.


g.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

ii.

Input DTC P0107 or P0108.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, race the engine for 1 minute, and then idle the engine for 5 minutes.



Result:
Proceed to
NEXT



NEXT

END

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED