| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P064C | Glow Plug Control Module | The MOS inside the glow plug control unit is detected as being stuck on 3 times while the glow plugs are on (2 trip detection logic). | Glow plug controller | Comes on | DTC stored |
| P066B | Cylinder 1 Glow Plug Control Circuit High | A short circuit in the No. 1 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic). | ·
Glow plug controller ·
No. 1 glow plug ·
Short in No. 1 glow plug circuit |
Comes on | DTC stored |
| P066D | Cylinder 2 Glow Plug Control Circuit High | A short circuit in the No. 2 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic). | ·
Glow plug controller ·
No. 2 glow plug ·
Short in No. 2 glow plug circuit |
Comes on | DTC stored |
| P066F | Cylinder 3 Glow Plug Control Circuit High | A short circuit in the No. 3 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic). | ·
Glow plug controller ·
No. 3 glow plug ·
Short in No. 3 glow plug circuit |
Comes on | DTC stored |
| P0671 | Cylinder 1 Glow Plug Circuit/Open | An open circuit in the No. 1 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic). | ·
Glow plug controller ·
No. 1 glow plug ·
Open in No. 1 glow plug circuit ·
GLOW relay |
Comes on | DTC stored |
| P0672 | Cylinder 2 Glow Plug Circuit/Open | An open circuit in the No. 2 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic). | ·
Glow plug controller ·
No. 2 glow plug ·
Open in No. 2 glow plug circuit ·
GLOW relay |
Comes on | DTC stored |
| P0673 | Cylinder 3 Glow Plug Circuit/Open | An open circuit in the No. 3 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic). | ·
Glow plug controller ·
No. 3 glow plug ·
Open in No. 3 glow plug circuit ·
GLOW relay |
Comes on | DTC stored |
| P0674 | Cylinder 4 Glow Plug Circuit/Open | An open circuit in the No. 4 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic). | ·
Glow plug controller ·
No. 4 glow plug ·
Open in No. 4 glow plug circuit ·
GLOW relay |
Comes on | DTC stored |
| P067B | Cylinder 4 Glow Plug Control Circuit High | A short circuit in the No. 4 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic). | ·
Glow plug controller ·
No. 4 glow plug ·
Short in No. 4 glow plug circuit |
Comes on | DTC stored |
| P166F | Glow Plug Control Module Circuit Short | A short circuit in a wire harness between the glow plugs is detected 3 times while the glow plugs are on (2 trip detection logic). | ·
Glow plug controller ·
Short in glow plug circuit |
Comes on | DTC stored |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P064C | Enter check mode |
| P066B | |
| P066D | |
| P066F | |
| P067B | |
| P0671 | |
| P0672 | |
| P0673 | |
| P0674 | |
| P166F |
Refer to DTC P052F.
Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>P052F
Inspect the fuses of circuits related to this system before performing the following procedure.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0671, P0672, P0673 and/or P0674 is output | A |
| P066B, P066D, P066F and/or P067B is output | B |
| P064C and/or P166F is output | C |
A
B
C
| *a | Front view of wire harness connector
(to Glow Plug Controller) |
Disconnect the glow plug controller connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A56-1(BATT) - Body ground | IG ON | 11 to 14 V |
Reconnect the glow plug controller connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect connectors of the glow plug controller.
| *1 | No. 1 Glow Plug Connector | - | - |
| *a | Front view of wire harness connector
(to Glow Plug Controller) |
*b | Front view of wire harness connector
(to Glow Plug Controller) |
Remove the No. 1 glow plug connector from the glow plug.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C98-1 (GL1) - No. 1 glow plug connector terminal 1 | Always | Below 1 Ω |
| C98-2 (GL2) - No. 1 glow plug connector terminal 2 | Always | Below 1 Ω |
| C97-1 (GL3) - No. 1 glow plug connector terminal 3 | Always | Below 1 Ω |
| C97-2 (GL4) - No. 1 glow plug connector terminal 4 | Always | Below 1 Ω |
Reconnect the glow plug controller connector.
Reinstall the No. 1 glow plug connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Exchange the glow plugs of the malfunctioning cylinders (the cylinders indicated by output DTCs) with the glow plugs of normally functioning cylinders.
Turn the ignition switch to ON.
Turn the GTS on.
Using the GTS, switch the ECM from normal mode to check mode.
| Tester Display |
|---|
| Check Mode |
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| Same DTCs (that have been erased) | A |
| Other DTCs | B |
Check for DTCs in check mode.
A
B
Replace the glow plug.
Click hereEngine / Hybrid System>1GD-FTV STARTING>GLOW PLUG>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Turn the GTS on.
Using the GTS, switch the ECM from normal mode to check mode.
| Tester Display |
|---|
| Check Mode |
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
Check for DTCs in check mode.
| Proceed to |
|---|
| NEXT |
NEXT
Inspect the GLOW relay.
Click hereEngine / Hybrid System>1GD-FTV STARTING>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) battery terminal.
Disconnect the cable from the positive (+) battery terminal.
Remove the GLOW relay from the engine room relay block and junction block.
Disconnect connectors of the glow plug controller.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| GLOW relay terminal 5 - Battery positive terminal | Always | Below 1 Ω |
| GLOW relay terminal 1 - Body ground | Always | Below 1 Ω |
| GLOW relay terminal 3 - A56-1 (BATT) | Always | Below 1 Ω |
| GLOW relay terminal 2 - G85-15 (GREL) | Always | Below 1 Ω |
| GLOW relay terminal 5 or Battery positive terminal - Body ground andother terminals | Always | 10 kΩ or higher |
| GLOW relay terminal 3 or A56-1 (BATT) - Body ground andother terminals | Always | 10 kΩ or higher |
| GLOW relay terminal 2 or G85-15 (GREL) - Body ground andother terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the GLOW relay.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect connectors of the glow plug controller.
| *1 | No. 1 Glow Plug Connector | - | - |
| *a | Front view of wire harness connector
(to Glow Plug Controller) |
*b | Front view of wire harness connector
(to Glow Plug Controller) |
Remove the No. 1 glow plug connector from the glow plug.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C98-1 (GL1) or No. 1 glow plug connector terminal 1 - Body ground | Always | 10 kΩ or higher |
| C98-2 (GL2) or No. 1 glow plug connector terminal 2 - Body ground | Always | 10 kΩ or higher |
| C97-1 (GL3) or No. 1 glow plug connector terminal 3 - Body ground | Always | 10 kΩ or higher |
| C97-2 (GL4) or No. 1 glow plug connector terminal 4 - Body ground | Always | 10 kΩ or higher |
Make sure that there are no short circuits to the battery.
Reconnect the glow plug controller connector.
Reinstall the No. 1 glow plug connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the glow plug controller.
Click hereEngine / Hybrid System>1GD-FTV STARTING>GLOW PLUG CONTROLLER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Turn the GTS on.
Using the GTS, switch the ECM from normal mode to check mode.
| Tester Display |
|---|
| Check Mode |
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
No DTC is output.
Check for DTCs in check mode.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the glow plug.
Click hereEngine / Hybrid System>1GD-FTV STARTING>GLOW PLUG>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect connectors of the glow plug controller.
| *1 | No. 1 Glow Plug Connector | - | - |
| *a | Front view of wire harness connector
(to Glow Plug Controller) |
*b | Front view of wire harness connector
(to Glow Plug Controller) |
Remove the No. 1 glow plug connector from the glow plug.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C98-1 (GL1) or No. 1 glow plug connector terminal 1 - Body ground | Always | 10 kΩ or higher |
| C98-2 (GL2) or No. 1 glow plug connector terminal 2 - Body ground | Always | 10 kΩ or higher |
| C97-1 (GL3) or No. 1 glow plug connector terminal 3 - Body ground | Always | 10 kΩ or higher |
| C97-2 (GL4) or No. 1 glow plug connector terminal 4 - Body ground | Always | 10 kΩ or higher |
Make sure that there are no short circuits to the battery.
Reconnect the glow plug controller connector.
Reinstall the No. 1 glow plug connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the glow plug controller.
Click hereEngine / Hybrid System>1GD-FTV STARTING>GLOW PLUG CONTROLLER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Turn the GTS on.
Using the GTS, switch the ECM from normal mode to check mode.
| Tester Display |
|---|
| Check Mode |
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
Check for DTCs in check mode.
| Proceed to |
|---|
| NEXT |
NEXT