Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM(w/ DPF)
RM3250E _51 Engine / Hybrid System _037972 1GD-FTV ENGINE CONTROL _0190004 ECD SYSTEM(w/ DPF) J

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  Cranking Holding Function Circuit  


DESCRIPTION

w/ Smart Entry and Start System and w/ Stop and Start System

While the engine is being cranked, the ECM detects the starter drive signal (STA2 signal) from the engine stop and start ECU as the starter operation signal (STA signal) to perform engine control when the engine is started. When the start signal is input from the engine switch, the certification ECU (smart key ECU assembly) sends the operation signal (STAR signal) to the ST NO. 1 relay (starter pinion drive relay) via the park/neutral position switch assembly. Afterward, the starter drive signal (STA2) is sent to the ST NO. 2 relay by the delay circuit in the engine stop and start ECU, and the starter is driven until the signal that the engine completely started (NE signal) is detected.

w/ Smart Entry and Start System and w/o Stop and Start System

While the engine is being cranked, current flows from terminal STAR of the certification ECU (smart key ECU assembly) to the park/neutral position switch assembly*1 or clutch start switch*2 and to terminal STA of the ECM (STA signal).

HINT:

*1: for Automatic Transmission

*2: for Manual Transmission


WIRING DIAGRAM

Refer to DTC P0617 for w/ Smart Entry and Start System.

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>P0617

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>INITIALIZATION).

·

Read Starter Count before replacing the engine stop and start ECU, perform the replacement procedure, and then write Starter Count to the newly installed engine stop and start ECU.

·

When replacing the engine stop and start ECU or the air conditioning amplifier assembly, initialize and learn the engine stop and start ECU air conditioning information.

·

When replacing the engine stop and start ECU or airbag ECU assembly (G sensor), initialize and learn the engine stop and start ECU G sensor zero point learned information.



PROCEDURE

1.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.


Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B



A

2.READ VALUE USING GTS (STARTER SIGNAL)

B

13.READ VALUE USING GTS (STARTER SIGNAL)
2.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the result when the ignition switch is ON and the engine starts.

OK:
Switch Condition Starter Signal
ON OFF
START ON



Result:
Proceed to
OK
NG



OK

3.INSPECT ST NO. 1 RELAY

NG

10.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY OR CLUTCH START SWITCH
3.INSPECT ST NO. 1 RELAY

Result:
Proceed to
OK
NG



OK

4.INSPECT STARTER ASSEMBLY

NG

REPLACE ST NO. 1 RELAY

4.INSPECT STARTER ASSEMBLY

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)
a.

Remove the ST NO. 1 relay from the engine room relay block and junction block.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (ST NO. 1 relay terminal holder) - C32-1 (ST) Always Below 1 Ω
3 (ST NO. 1 relay terminal holder) or C32-1 (ST) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY)
a.

Disconnect the starter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D3-1 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
a.

Remove the ST NO. 1 relay from the engine room relay block and junction block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ST NO. 1 relay terminal holder) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY OR CLUTCH START SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY OR CLUTCH START SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)
HINT:

*1: for Automatic Transmission

*2: for Manual Transmission


a.

Remove the ST NO. 1 relay from the engine room relay block and junction block.


b.

Disconnect the park/neutral position switch assembly connector.*1


c.

Disconnect the clutch start switch connector.*2


d.

Disconnect the certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-5 (L)*1 - 2 (ST NO. 1 relay terminal holder) Always Below 1 Ω
B2-1*2 - 2 (ST NO. 1 relay terminal holder) Always Below 1 Ω
G70-37 (STA) - 2 (ST NO. 1 relay terminal holder) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (BATTERY - ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (BATTERY - ST NO. 1 RELAY)
a.

Remove the ST NO. 1 relay from the engine room relay block and junction block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (ST NO. 1 relay terminal holder) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY OR CLUTCH START SWITCH
HINT:

*1: for Automatic Transmission

*2: for Manual Transmission



b.

Inspect the clutch start switch.*2

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG (for Automatic Transmission)
NG (for Manual Transmission)



OK

11.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY OR CLUTCH START SWITCH - ECM - ST NO. 1 RELAY - CERTIFICATION ECU)

NG (for Automatic Transmission)

NG (for Manual Transmission)

REPLACE CLUTCH START SWITCH

11.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY OR CLUTCH START SWITCH - ECM - ST NO. 1 RELAY - CERTIFICATION ECU)
HINT:

*1: for Automatic Transmission

*2: for Manual Transmission


a.

Disconnect the park/neutral position switch assembly connector.*1


b.

Disconnect the clutch start switch connector.*2


c.

Disconnect the ECM connector.


d.

Remove the ST NO. 1 relay from the engine room relay block and junction block.


e.

Disconnect the certification ECU (smart key ECU assembly) connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-5 (L) - G85-22 (STA)*1 Always Below 1 Ω
B2-1 - G85-22 (STA)*2 Always Below 1 Ω
C24-5 (L) or G85-22 (STA) or 2 (ST NO. 1 relay terminal holder) or G17-37 (STA) - Body ground and other terminals*1 Always 10 kΩ or higher
B2-1 or G85-22 (STA) or 2 (ST NO. 1 relay terminal holder) or G17-37 (STA) - Body ground and other terminals*2 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY OR CLUTCH START SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY OR CLUTCH START SWITCH - ECM)
HINT:

*1: for Automatic Transmission

*2: for Manual Transmission


a.

Disconnect the park/neutral position switch assembly connector.*1


b.

Disconnect the clutch start switch connector.*2


c.

Disconnect the certification ECU (smart key ECU assembly) connector.


d.

Disconnect the ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G70-16 (STAR) - C24-4 (B)*1 Always Below 1 Ω
G70-16 (STAR) - B2-2*2 Always Below 1 Ω
G70-16 (STAR) - G85-11 (NSW) Always Below 1 Ω
G70-16 (STAR) or C24-4 (B) or G85-11 (NSW) - Body ground and other terminals*1 Always 10 kΩ or higher
G70-16 (STAR) or B2-2 or G85-11 (NSW) - Body ground and other terminals*2 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the result when the ignition switch is ON and the engine starts.

OK:
Switch Condition Starter Signal
ON OFF
START ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 1 RELAY - ECM)