Refer to DTC P0031.
Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>P0031
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2195 | Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) | While fuel-cut operation performed (during vehicle deceleration), air fuel ratio sensor voltage is 2.12 V or higher for 5 seconds (2 trip detection logic). | ·
Air fuel ratio sensor ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P2195 | ·
AFS Voltage B1S1 ·
AF Sensor Leaning Value |
When the air fuel ratio sensor output deviates to lean due to a malfunction in the sensor, white smoke occurs since the ECM performs control for a lean condition. The ECM monitors the current value of the sensor in the fuel cut to detect abnormal current. If the ECM detects an air fuel ratio sensor voltage of 2.65 V or higher for a cumulative time of 5 seconds or more, the ECM judges that there is a malfunction in the air fuel ratio sensor and stores DTC P2195.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P2195 | After the engine is fully warmed up, the accelerator pedal is released for 7 seconds or more immediately after the vehicle is accelerated to a speed of between 60 and 80 km/h (37 and 50 mph). |
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Replace the air fuel ratio sensor.
Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Start the engine and warm it up.
After the engine is fully warmed up, the accelerator pedal is released for 7 seconds or more immediately after the vehicle is accelerated to a speed of between 60 and 80 km/h (37 and 50 mph).
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the pending DTC is not output.
If no pending DTCs are output, proceed to the next step to check "All Readiness".
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P2195.
Check the DTC judgment result.
| GTS Display | Result | Proceed to |
|---|---|---|
| Pending DTC | DTC P2195 is output | B |
| All Readiness | NORMAL | A |
| ABNORMAL | B |
If STATUS is INCOMPLETE or N/A, the accelerator pedal is released for 7 seconds or more immediately after the vehicle is accelerated to a speed of between 60 and 80 km/h (37 and 50 mph) again.
A
B