Home › Drivetrain › CLUTCH › CLUTCH PEDAL › 2015.06–2016.01
RM3250E _52 Drivetrain _038032 CLUTCH _0190441 CLUTCH PEDAL A

CLUTCH  CLUTCH PEDAL  INSTALLATION  


PROCEDURE

Hide 31301S 1.INSTALL NO. 2 CLUTCH PEDAL CUSHION

a.
C319908

Install the No. 2 clutch pedal cushion to the clutch pedal sub-assembly.


b.
C319909

Install the No. 2 clutch pedal cushion to the clutch pedal sub-assembly.


Hide 31395 2.INSTALL PEDAL SPRING HOOK (w/ Turn Over)

a.
C319911C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the contact surface of the pedal spring hook and install the pedal spring hook to the clutch pedal support sub-assembly.


Hide 31453B 3.INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSH

a.
C319913C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the inside of a new clutch master cylinder push rod clevis bush.


b.

Install the clutch master cylinder push rod clevis bush to the clutch pedal sub-assembly.

HINT:

Install the clutch master cylinder push rod clevis bush from the left side of the vehicle.



Hide 31301B 4.INSTALL NO. 1 CLUTCH PEDAL CUSHION

a.
C319905

Install the No. 1 clutch pedal cushion to the clutch pedal sub-assembly.


Hide 31301C 5.INSTALL CLUTCH PEDAL BUSH

a.
C319914C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the collar and the inside and outside of 2 new clutch pedal bushes.


b.

Install the 2 clutch pedal bushes and collar to the clutch pedal sub-assembly.


Hide 31301P 6.INSTALL CLUTCH PEDAL TURNOVER BUSH (w/ Turn Over)

a.
C319915C02
0,0 0,0 false
V100135

MP grease


Apply MP grease to the inside of the clutch pedal turnover bush and install the bush to the clutch pedal sub-assembly.


Hide 31353 7.INSTALL CLUTCH PEDAL SPRING HOLDER (w/ Turn Over)

a.
C319916C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the contact surface of the clutch pedal spring holder and install the clutch pedal spring holder to the clutch pedal support sub-assembly.


Hide 31301 8.INSTALL CLUTCH PEDAL SUB-ASSEMBLY

a.

Install the clutch pedal sub-assembly to the clutch pedal support sub-assembly with the bolt and nut.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)

HINT:

Install the bolt from the right side of the vehicle.



Hide 9.INSTALL CLUTCH PEDAL SPRING (w/ Turn Over)

a.

Move the pedal to the full stroke position.


b.

Install the clutch pedal spring to the clutch pedal assembly.


c.
C323279C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the inside of the hole in the hook and to the sliding areas of the spring.


d.
C319917C02
0,0 0,0 false
V113147

Install in this Direction


Install the pedal spring with hook.


Hide 84520 10.INSTALL CLUTCH START SWITCH ASSEMBLY

Hide 88280A 11.INSTALL CLUTCH SWITCH ASSEMBLY

Hide 31321 12.INSTALL CLUTCH PEDAL PAD

Hide 13.INSTALL CLUTCH PEDAL SUPPORT ASSEMBLY

a.
C319898N01
0.458,0.833 0.615,1.031 0.156,0.198 10 false A 0.854,1.271 1.01,1.469 0.156,0.198 10 false A 2.49,0.177 2.646,0.375 0.156,0.198 10 false B

Install the clutch pedal support assembly with the bolt and 2 nuts.

Torque:
for nut A : 18.4 N*m (188 kgf*cm, 14 ft.*lbf)
for bolt B : 18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

w/ Clutch Switch:

Connect the clutch switch connector.


Hide 14.CONNECT CLUTCH MASTER CYLINDER PUSH ROD CLEVIS

a.
C323275C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the contact surface of the clevis pin.


b.
C323276C01
0.219,0.281 0.531,0.438 0.313,0.156 10 false *a 2.073,0.156 2.385,0.313 0.313,0.156 10 false *b
*a Correct
*b Incorrect


Connect the clutch master cylinder push rod clevis with the clevis pin and install a new clip.


c.

w/o Turnover:

Connect the clutch pedal spring to the clevis pin and clutch pedal support to install it.


Hide 15.INSPECT AND ADJUST CLUTCH PEDAL ASSEMBLY

Hide 55302A 16.INSTALL INSTRUMENT UPPER PANEL SUB-ASSEMBLY

Hide 17.CHECK FLUID LEVEL IN RESERVOIR