Home › Engine / Hybrid System › 2GD-FTV INTAKE / EXHAUST › EXHAUST MANIFOLD W/ TURBOCHARGER
RM3250E _51 Engine / Hybrid System _038009 2GD-FTV INTAKE / EXHAUST _0191566 EXHAUST MANIFOLD W/ TURBOCHARGER A

2GD-FTV INTAKE / EXHAUST  EXHAUST MANIFOLD W/ TURBOCHARGER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A344970

Using an E10 "TORX" socket wrench, install the 3 stud bolts at the positions shown in the illustration.

Torque:
14.7 N*m (150 kgf*cm, 11 ft.*lbf)


b.
A344969

Using an E8 "TORX" socket wrench, install the 4 stud bolts at the positions shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.
A344968

Using an E5 "TORX" socket wrench, install the 4 stud bolts at the positions shown in the illustration.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17275 2.INSTALL COMPRESSOR OUTLET ELBOW

a.

except Cold Specification Vehicles:

Install the hose clamp with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install a new gasket.


c.

Install a new gasket and the compressor outlet elbow with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 17274 3.INSTALL COMPRESSOR INLET ELBOW

a.

Using an E8 "TORX" socket wrench, install a new gasket and the compressor inlet elbow with the stud bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install the compressor inlet elbow to the turbocharger sub-assembly with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.

Install the compressor inlet elbow stay with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16027 4.INSTALL NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

a.

Install a new gasket.


b.

Temporarily install the No. 1 turbo water pipe sub-assembly with the bolt and 2 nuts.


c.

Tighten the bolt and 2 nuts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 15407 5.TEMPORARILY INSTALL TURBO OIL INLET PIPE SUB-ASSEMBLY

a.
A345118C01
2.448,1.802 2.76,1.958 0.313,0.156 10 true *b 0.729,1.813 1.042,1.969 0.313,0.156 10 true *a
*a NG
*b OK


Install a new gasket as shown in the illustration.

NOTICE:

Do not install the gasket upside down.



b.

Temporarily install the turbo oil inlet pipe sub-assembly with the 2 nuts.


Hide 17141 6.TEMPORARILY INSTALL EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY

a.

Install 2 new gaskets to the exhaust manifold and turbocharger sub-assembly.


b.

Temporarily install the exhaust manifold to turbocharger sub-assembly with 3 new nuts.


c.
A359584C01
1.083,1.885 1.219,1.99 1.219,1.99 1.427,1.99 false 0.979,4.344 1.115,4.448 1.115,4.448 1.323,4.448 false 0.063,0.042 0.375,0.198 0.313,0.156 10 true *A 0.115,2.219 0.427,2.375 0.313,0.156 10 false *B 1.438,1.875 1.75,2.031 0.313,0.156 10 false *1 1.344,4.333 1.667,4.49 0.323,0.156 10 false *1
*A w/ DPF
*B w/o DPF
*1 Collar
V100136

Engine Side


Temporarily install the exhaust manifold with turbocharger sub-assembly, 8 collars and the 8 plate washers to the cylinder head with 8 new nuts.

NOTICE:

Make sure that the side of the collar with the smaller diameter faces the exhaust manifold.



d.

Install a new gasket on the union bolt side to turbo oil inlet pipe sub-assembly.


e.

Temporarily install the union bolt.


Hide 15474 7.INSTALL TURBO OIL OUTLET PIPE

a.

Install a new gasket to the turbo oil outlet pipe.

NOTICE:

The claws of the gasket must face the turbo oil outlet pipe.



b.

Install the turbo oil outlet pipe with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


c.

Connect the turbo oil outlet hose to the turbo oil outlet pipe, turbo oil inlet pipe and slide the 2 hose clips to secure the hoses.


Hide 17293 8.TEMPORARILY INSTALL TURBOCHARGER STAY

a.

Temporarily install the turbocharger stay to the turbocharger sub-assembly, with 3 bolts and nut.


Hide 17141 9.TIGHTEN EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY

a.
A359724C01
0.063,0.031 0.375,0.188 0.313,0.156 10 true *A 0.135,2.25 0.448,2.406 0.313,0.156 10 false *B 0.885,2.469 1.042,2.667 0.156,0.198 10 true 6 1.344,2.458 1.5,2.656 0.156,0.198 10 true 1 1.917,2.49 2.073,2.688 0.156,0.198 10 true 2 2.25,2.479 2.406,2.677 0.156,0.198 10 true 7 2.521,3.844 2.677,4.042 0.156,0.198 10 true 8 2.177,3.844 2.333,4.042 0.156,0.198 10 true 3 1.781,3.813 1.938,4.01 0.156,0.198 10 true 4 0.49,3.833 0.646,4.031 0.156,0.198 10 true 5 2.479,1.323 2.635,1.521 0.156,0.198 10 true 8 2.188,1.333 2.344,1.531 0.156,0.198 10 true 3 1.76,1.323 1.917,1.521 0.156,0.198 10 true 4 0.625,1.375 0.781,1.573 0.156,0.198 10 true 5 0.885,0.021 1.042,0.219 0.156,0.198 10 true 6 1.344,0.021 1.5,0.219 0.156,0.198 10 true 1 1.917,0 2.073,0.198 0.156,0.198 10 true 2 2.229,0.031 2.385,0.229 0.156,0.198 10 true 7
*A w/ DPF
*B w/o DPF


Tighten the exhaust manifold with turbocharger sub-assembly, to the cylinder head with 8 nuts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:

Tighten the nuts in the order shown in the illustration.



b.

Tighten the turbocharger sub-assembly, to the exhaust manifold with the 3 nuts.

Torque:
73 N*m (744 kgf*cm, 54 ft.*lbf)


c.

Tighten the 2 nuts and then union bolt of the turbo oil inlet pipe sub-assembly.

Torque:
for nut : 13 N*m (133 kgf*cm, 10 ft.*lbf)
for union bolt : 36 N*m (367 kgf*cm, 27 ft.*lbf)

NOTICE:

If the connecting part of the union bolt gasket is cracked, remove the connecting part.



Hide 17293 10.TIGHTEN TURBOCHARGER STAY

a.
A344955E01
1.833,0.188 2.042,0.417 0.208,0.229 10 true 1 2.771,0.448 2.979,0.677 0.208,0.229 10 true 2 1.531,2.969 1.74,3.198 0.208,0.229 10 true 3 0.365,1.99 0.573,2.219 0.208,0.229 10 true 4

Tighten the 3 bolts and nut of the turbocharger stay in the order shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


Hide 87101 11.INSTALL NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)

a.

Temporarily install the No. 1 viscous heater bracket sub-assembly with 4 bolts.


b.
A360494E01
0.635,0.521 0.885,0.719 0.25,0.198 10 true 2 2.625,0.417 2.875,0.615 0.25,0.198 10 true 4 2.885,1.583 3.135,1.781 0.25,0.198 10 true 1 1.573,2.583 1.823,2.781 0.25,0.198 10 true 3

Tighten the 4 bolts and of the No. 1 viscous heater bracket sub-assembly in the order shown in the illustration.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 12.INSTALL WIRE HARNESS CLAMP BRACKET (for Manual Transmission)

a.

w/o DPF:

Connect the wire harness with the bolt.

Torque:
18.6 N*m (190 kgf*cm, 14 ft.*lbf)


b.

w/ DPF:

Connect the wire harness clamp and install the bolt.

Torque:
18.6 N*m (190 kgf*cm, 14 ft.*lbf)


c.

w/ DPF:

for Automatic Transmission:

Connect the oil cooler tube bracket with the bolt.

Torque:
13.5 N*m (138 kgf*cm, 10 ft.*lbf)


Hide 13.INSTALL OIL COOLER TUBE BRACKET AND WIRE HARNESS CLAMP BRACKET (for Automatic Transmission)

a.

w/o DPF:

Connect the wire harness with the bolt.

Torque:
18.6 N*m (190 kgf*cm, 14 ft.*lbf)


b.

w/ DPF:

Attach the 2 wire harness clamps and connect the wire harness.


c.

for Automatic Transmission:

Connect the oil cooler tube bracket with the bolt.

Torque:
13.5 N*m (138 kgf*cm, 10 ft.*lbf)


Hide 25601 14.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY (w/o DPF)

Hide 15.INSTALL EGR PIPE WITH COOLER SUB-ASSEMBLY (w/ DPF)

Hide 16284 16.CONNECT TURBO WATER HOSE

a.

Connect the No. 1 turbo water hose and No. 2 turbo water hose to the water outlet sub-assembly, engine water pump assembly and slide the 2 hose clips to secure the hoses.

NOTICE:

The turbocharger sub-assembly may be damaged if the No. 1 turbo water hose and No. 2 turbo water hose are connected to the wrong locations.



Hide 16268 17.INSTALL NO. 1 WATER BY-PASS PIPE

Hide 12261 18.INSTALL PCV HOSE (except Cold Area Specification Vehicles)

a.

Attach the clamp and install the PCV hose.


b.

Slide the 2 hose clips to secure the hoses.


Hide 12229 19.INSTALL PCV PIPE (for Cold Area Specification Vehicles)

a.

Connect the PCV pipe to the compressor inlet elbow, cylinder head cover sub-assembly and slide the 2 hose clips to secure the hoses.


b.

Install the PCV pipe with the bolt to the compressor outlet elbow.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the No. 19 water by-pass hose to the compressor inlet elbow and slide the hose clip to secure the hoses.


d.

Install the No. 20 water by-pass hose to the PCV pipe and No. 1 water by-pass pipe, and slide the 2 hose clips to secure the hoses.


Hide 16279 20.INSTALL NO. 3 WATER BY-PASS PIPE

a.

Connect the 2 water hoses to the oil cooler assembly and No. 2 water by-pass pipe, and slide the 2 hose clips to secure the hoses.


b.

Install the No. 3 water by-pass pipe with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.

for Cold Specification Vehicles:

Install the water hose to the compressor inlet elbow and No. 3 water by-pass pipe, and slide the 2 hose clips to secure the hoses.


Hide 87120G 21.INSTALL VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY (w/ Viscous Heater)

Hide 22.INSTALL WATER HOSE SUB-ASSEMBLY (w/ Viscous Heater)

Hide 17701 23.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.

Install the air cleaner case sub-assembly with the 3 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


b.

Connect the 3 wire harness clamps.


Hide 17801 24.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Install the air cleaner filter element sub-assembly to the air cleaner case.


Hide 17705 25.INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE

a.

Attach the 4 clips to install the air cleaner cap sub-assembly with air cleaner hose.


b.

Tighten the hose clamp.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.

Connect the mass air flow meter connector and attach the 2 wire harness clamps.


Hide 16711 26.INSTALL FAN SHROUD

Hide 16470 27.INSTALL RADIATOR RESERVOIR

Hide 44369A 28.INSTALL NO. 1 OIL RESERVOIR BRACKET

Hide 44360 29.CONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 16571C 30.INSTALL NO. 1 RADIATOR HOSE

Hide 17362B 31.INSTALL NO. 2 AIR TUBE

Hide 17344E 32.INSTALL NO. 4 AIR HOSE

Hide 37.INSPECT FOR COOLANT LEAK

Hide 51410 41.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY