Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(for Type A)
RM3250E _58 Vehicle Interior _038070 SUPPLEMENTAL RESTRAINT SYSTEMS _0193717 AIRBAG SYSTEM(for Type A) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for Type A)  B1900/73  Short in Front Pretensioner Squib RH Circuit  B1901/73  Open in Front Pretensioner Squib RH Circuit  B1902/73  Short to GND in Front Pretensioner Squib RH Circuit  B1903/73  Short to B+ in Front Pretensioner Squib RH Circuit  


DESCRIPTION

The front pretensioner RH circuit consists of the airbag sensor assembly and front seat outer belt assembly RH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front pretensioner RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1900/73 Short in Front Pretensioner Squib RH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal 5 times in the front pretensioner RH circuit during the primary check.

·

A front seat outer belt assembly RH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

No. 1 rear door wire*

·

Front seat outer belt assembly RH

·

Airbag sensor assembly


B1901/73 Open in Front Pretensioner Squib RH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects an open circuit signal in the front pretensioner RH circuit for 2 seconds.

·

A front seat outer belt assembly RH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

No. 1 rear door wire*

·

Front seat outer belt assembly RH

·

Airbag sensor assembly


B1902/73 Short to GND in Front Pretensioner Squib RH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to ground signal in the front pretensioner RH circuit for 0.5 seconds.

·

A front seat outer belt assembly RH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

No. 1 rear door wire*

·

Front seat outer belt assembly RH

·

Airbag sensor assembly


B1903/73 Short to B+ in Front Pretensioner Squib RH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to B+ signal in the front pretensioner RH circuit for 0.5 seconds.

·

A front seat outer belt assembly RH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

No. 1 rear door wire*

·

Front seat outer belt assembly RH

·

Airbag sensor assembly



*: for Smart Cab

WIRING DIAGRAM

C326506E07
0.542,3.094 2.375,3.292 1.833,0.198 10 false L10*1, N19*2 0.531,3.313 3,3.604 2.469,0.292 10 false Front Seat Outer Belt Assembly RH 4.927,4.188 5.313,4.375 0.385,0.188 10 false N15 4.927,4.354 6.76,4.552 1.833,0.198 10 false Airbag Sensor Assembly 3.438,1.677 3.823,1.865 0.385,0.188 10 false NL1 3.448,1.479 3.833,1.667 0.385,0.188 10 false 1*1 3.458,2.302 3.844,2.49 0.385,0.188 10 false 2*1 3.458,1.958 3.844,2.146 0.385,0.188 10 false *2 3.458,2.781 3.844,2.969 0.385,0.188 10 false *2 0.396,4.063 2.865,4.354 2.469,0.292 10 false *1: for Smart Cab 0.396,4.375 2.865,4.667 2.469,0.292 10 false *2: for Single Cab, Double Cab 2.167,1.583 2.552,1.771 0.385,0.188 10 false R+ 2.167,2.385 2.552,2.573 0.385,0.188 10 false R- 2.458,1.573 2.844,1.76 0.385,0.188 10 false 2 2.448,2.406 2.833,2.594 0.385,0.188 10 false 1 4.563,1.563 4.948,1.75 0.385,0.188 10 false 2 4.583,2.406 4.969,2.594 0.385,0.188 10 false 1 4.802,1.667 5.188,1.854 0.385,0.188 10 false PR+ 4.813,2.531 5.198,2.719 0.385,0.188 10 false PR- 3.438,2.531 3.823,2.719 0.385,0.188 10 false NL1

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for Smart Cab A
for Single Cab, Double Cab B



A

2.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH

B

7.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH
2.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH
a.
C326689C01
0.458,2 0.875,2.292 0.417,0.292 2.281,2.198 2.469,2.198 false 0.469,0.604 0.781,0.76 0.313,0.156 10 false *1 2.219,1.125 2.531,1.281 0.313,0.156 10 false *2 2.552,1.583 2.979,1.823 0.427,0.24 10 false *3 2.542,2.135 2.854,2.292 0.313,0.156 10 false *4 1.667,1.365 1.979,1.521 0.313,0.156 10 false *a 0.542,2.083 0.885,2.26 0.344,0.177 10 false L10 1.906,0.813 2.219,0.969 0.313,0.156 10 false A 1.365,1.083 1.677,1.24 0.313,0.156 10 false C 1.26,1.083 1.573,1.24 0.313,0.156 10 false D 0.875,1.094 1.188,1.25 0.313,0.156 10 false E 0.646,1.094 0.958,1.25 0.313,0.156 10 false F
*1 Front Seat Outer Belt Assembly RH
*2 Airbag Sensor Assembly
*3 Connector E
*4 SST
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH)


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the front seat outer belt assembly RH.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector E.

CAUTION:

Never connect the tester to the front seat outer belt assembly RH for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output
DTC B1905/74, B1906/74, B1907/74 or B1908/74 is output


HINT:

Codes other than DTC B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.



k.

Turn the ignition switch off.


l.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


m.

Disconnect SST from connector E.



DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output

REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH

DTC B1905/74, B1906/74, B1907/74 or B1908/74 is output

3.CHECK CONNECTORS
3.CHECK CONNECTORS
a.

Disconnect the connector from the airbag sensor assembly.


b.
C326690C01
0.417,1 0.729,1.156 0.313,0.156 10 false *1 0.958,1.01 1.271,1.167 0.313,0.156 10 false *2 1.479,1.01 1.792,1.167 0.313,0.156 10 false *3 2.156,1.281 2.469,1.438 0.313,0.156 10 false A 1.74,1.583 2.052,1.74 0.313,0.156 10 false B 2.417,1.583 2.729,1.74 0.313,0.156 10 false *4 1.344,1.583 1.656,1.74 0.313,0.156 10 false C 1.208,1.583 1.521,1.74 0.313,0.156 10 false D 0.823,1.573 1.135,1.729 0.313,0.156 10 false E 0.583,1.573 0.896,1.729 0.313,0.156 10 false F
*1 Front Seat Outer Belt Assembly RH
*2 No. 1 Rear Door Wire
*3 Floor Wire
*4 Airbag Sensor Assembly


Check that the connectors (on the airbag sensor assembly side and front seat outer belt assembly RH side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

4.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH CIRCUIT

NG

REPLACE NO. 1 REAR DOOR WIRE OR FLOOR WIRE

4.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH CIRCUIT
a.
C326691C01
0.5,2.198 0.969,2.49 0.469,0.292 1.229,2.813 1.635,2.479 true 2.271,2.813 1.792,2.479 true 0.427,0.917 0.74,1.073 0.313,0.156 10 false *1 1.01,0.927 1.323,1.083 0.313,0.156 10 false *2 1.479,0.906 1.792,1.063 0.313,0.156 10 false *3 2.396,1.49 2.708,1.646 0.313,0.156 10 false *4 2.26,2.198 2.573,2.354 0.313,0.156 10 false *5 1.615,1.875 1.927,2.031 0.313,0.156 10 false *a 2.198,1.146 2.51,1.302 0.313,0.156 10 false A 1.76,1.417 2.073,1.573 0.313,0.156 10 false B 1.375,1.417 1.688,1.573 0.313,0.156 10 false C 1.26,1.417 1.573,1.573 0.313,0.156 10 false D 0.875,1.417 1.188,1.573 0.313,0.156 10 false E 0.625,1.417 0.938,1.573 0.313,0.156 10 false F 0.635,2.26 1.115,2.417 0.479,0.156 10 false L10 1.104,2.854 1.583,3.01 0.479,0.156 10 false R- 2.229,2.865 2.708,3.021 0.479,0.156 10 false R+
*1 Front Seat Outer Belt Assembly RH
*2 No. 1 Rear Door Wire
*3 Floor Wire
*4 Airbag Sensor Assembly
*5 Connector E
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L10-2 (R+) - Body ground Ignition switch ON Below 1 V
L10-1 (R-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L10-1 (R-) - L10-2 (R+) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>DIAGNOSIS SYSTEM


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L10-2 (R+) - L10-1 (R-) Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L10-2 (R+) - Body ground Always 1 MΩ or higher
L10-1 (R-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK DTC

NG

6.CHECK NO. 1 REAR DOOR WIRE
5.CHECK DTC
a.
C326692C01
0.604,0.979 0.917,1.135 0.313,0.156 10 false *1 2.208,1.583 2.521,1.74 0.313,0.156 10 false *2 1.927,1.25 2.24,1.406 0.313,0.156 10 false A 1.385,1.51 1.698,1.667 0.313,0.156 10 false C 1.229,1.51 1.542,1.667 0.313,0.156 10 false D 0.906,1.51 1.219,1.667 0.313,0.156 10 false E 0.708,1.51 1.021,1.667 0.313,0.156 10 false F
*1 Front Seat Outer Belt Assembly RH
*2 Airbag Sensor Assembly


Connect the connectors to the front seat outer belt assembly RH and airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output
DTC B1905/74, B1906/74, B1907/74 or B1908/74 is output


HINT:

Codes other than DTC B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.




DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output

DTC B1905/74, B1906/74, B1907/74 or B1908/74 is output

6.CHECK NO. 1 REAR DOOR WIRE
a.
C326693C01
0.563,2.031 0.979,2.313 0.417,0.281 1.208,2.76 1.656,2.469 true 2.25,2.75 1.823,2.469 true 0.333,0.906 0.646,1.063 0.313,0.156 10 false *1 0.906,0.896 1.219,1.052 0.313,0.156 10 false *2 1.531,0.885 1.844,1.042 0.313,0.156 10 false *3 2.438,1.438 2.75,1.594 0.313,0.156 10 false *4 2.427,2.115 2.74,2.271 0.313,0.156 10 false *5 1.708,1.875 2.021,2.031 0.313,0.156 10 false *a 0.667,2.104 1.177,2.333 0.51,0.229 10 false L10 2.25,2.771 2.76,3 0.51,0.229 10 false R+ 1.125,2.802 1.635,3.031 0.51,0.229 10 false R- 2.208,1.125 2.521,1.281 0.313,0.156 10 false A 1.781,1.406 2.094,1.563 0.313,0.156 10 false B 1.385,1.417 1.698,1.573 0.313,0.156 10 false C 1.156,1.406 1.469,1.563 0.313,0.156 10 false D 0.729,1.427 1.042,1.583 0.313,0.156 10 false E 0.49,1.427 0.802,1.583 0.313,0.156 10 false F
*1 Front Seat Outer Belt Assembly RH
*2 No. 1 Rear Door Wire
*3 Floor Wire
*4 Airbag Sensor Assembly
*5 Connector E
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH)


Disconnect the connector from floor wire.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L10-2 (R+) - Body ground Ignition switch ON Below 1 V
L10-1 (R-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L10-1 (R-) - L10-2 (R+) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector D.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>DIAGNOSIS SYSTEM


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L10-2 (R+) - L10-1 (R-) Always 1 MΩ or higher



j.

Restore the released activation prevention mechanism of connector D to its original condition.


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L10-2 (R+) - Body ground Always 1 MΩ or higher
L10-1 (R-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FLOOR WIRE

NG

REPLACE NO. 1 REAR DOOR WIRE

7.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH
a.
C326694C03
0.573,1.948 0.99,2.229 0.417,0.281 2.042,2.323 2.219,2.396 false 0.854,0.75 1.167,0.906 0.313,0.156 10 false *1 2.073,1.281 2.385,1.438 0.313,0.156 10 false *2 2.219,2.063 2.531,2.219 0.313,0.156 10 false *3 2.271,2.344 2.583,2.5 0.313,0.156 10 false *4 1.531,1.583 1.844,1.74 0.313,0.156 10 false *a 0.656,2.021 1.146,2.198 0.49,0.177 10 false N19 1.76,0.99 2.073,1.146 0.313,0.156 10 false A 1.25,1.229 1.563,1.385 0.313,0.156 10 false C 1,1.229 1.313,1.385 0.313,0.156 10 false D
*1 Front Seat Outer Belt Assembly RH
*2 Airbag Sensor Assembly
*3 Connector C
*4 SST
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH)


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the front seat outer belt assembly RH.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt assembly RH for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output
DTC B1905/74, B1906/74, B1907/74 or B1908/74 is output


HINT:

Codes other than DTC B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.



k.

Turn the ignition switch off.


l.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


m.

Disconnect SST from connector C.



DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output

DTC B1905/74, B1906/74, B1907/74 or B1908/74 is output

8.CHECK CONNECTORS
8.CHECK CONNECTORS
a.

Disconnect the connector from the airbag sensor assembly.


b.
C326695C01
0.635,1.135 0.948,1.292 0.313,0.156 10 false *1 1.24,1.115 1.552,1.271 0.313,0.156 10 false *2 2.104,1.677 2.417,1.833 0.313,0.156 10 false *3 1.896,1.365 2.208,1.521 0.313,0.156 10 false A 1.479,1.615 1.792,1.771 0.313,0.156 10 false B 1.063,1.615 1.375,1.771 0.313,0.156 10 false C 0.823,1.625 1.135,1.781 0.313,0.156 10 false D
*1 Front Seat Outer Belt Assembly RH
*2 Floor Wire
*3 Airbag Sensor Assembly


Check that the connectors (on the airbag sensor assembly side and front seat outer belt assembly RH side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

9.CHECK FLOOR WIRE

NG

REPLACE FLOOR WIRE

9.CHECK FLOOR WIRE
a.
C326696C03
0.458,1.979 0.938,2.25 0.479,0.271 1.156,2.604 1.573,2.188 true 2.167,2.604 1.719,2.198 true 0.667,0.75 0.979,0.906 0.313,0.156 10 false *1 1.167,0.708 1.479,0.865 0.313,0.156 10 false *2 2.021,1.229 2.333,1.385 0.313,0.156 10 false *3 2.156,1.875 2.469,2.031 0.313,0.156 10 false *4 1.531,1.594 1.844,1.75 0.313,0.156 10 false *a 0.573,2.031 1.052,2.24 0.479,0.208 10 false N19 1.073,2.635 1.552,2.844 0.479,0.208 10 false R- 2.125,2.656 2.604,2.865 0.479,0.208 10 false R+ 1.792,0.938 2.104,1.094 0.313,0.156 10 false A 1.417,1.188 1.729,1.344 0.313,0.156 10 false B 1.052,1.198 1.365,1.354 0.313,0.156 10 false C 0.823,1.198 1.135,1.354 0.313,0.156 10 false D
*1 Front Seat Outer Belt Assembly RH
*2 Floor Wire
*3 Airbag Sensor Assembly
*4 Connector C
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N19-1 (R-) - Body ground Ignition switch ON Below 1 V
N19-2 (R+) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N19-1 (R-) - N19-2 (R+) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>DIAGNOSIS SYSTEM


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N19-1 (R-) - N19-2 (R+) Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N19-1 (R-) - Body ground Always 1 MΩ or higher
N19-2 (R+) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK DTC

NG

REPLACE FLOOR WIRE

10.CHECK DTC
a.
C269343C03
0.792,0.823 1.104,1.021 0.313,0.198 10 false *1 1.01,1.229 1.323,1.427 0.313,0.198 10 false D 1.125,1.229 1.438,1.427 0.313,0.198 10 false C 1.99,1.323 2.302,1.521 0.313,0.198 10 false *2
*1 Front Seat Outer Belt Assembly RH
*2 Airbag Sensor Assembly


Connect the connectors to the front seat outer belt assembly RH and airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output
DTC B1905/74, B1906/74, B1907/74 or B1908/74 is output


HINT:

Codes other than DTC B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.




DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output

DTC B1905/74, B1906/74, B1907/74 or B1908/74 is output