Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM3250E _52 Drivetrain _038029 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0194108 AUTOMATIC TRANSMISSION SYSTEM C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P2716  Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)  


DESCRIPTION

Shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and vehicle speed sensor. The TCM adjusts the current of the shift solenoid valve SLT to control the hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.

C221301E09
4.885,2.063 5.208,1.125 5.208,1.125 5.271,1.125 true 5.031,2.208 5.188,2.573 5.188,2.573 5.26,2.573 true 5.875,2.271 6,2.573 6,2.573 6.063,2.573 true 6.115,2.479 7,2.698 0.885,0.219 10 false Solenoid Coil 0.104,0.677 1.354,0.896 1.25,0.219 10 false Hydraulic Pressure 2.563,3.01 3.125,3.229 0.563,0.219 10 false Current 5.313,2.49 5.844,2.708 0.531,0.219 10 false Sleeve 5.323,1.031 6.167,1.25 0.844,0.219 10 false Spool Valve

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT) Open or short is detected in the shift solenoid valve SLT circuit for 1 second or more while driving (1-trip detection logic).
·

Open or short in shift solenoid valve SLT circuit

·

Shift solenoid valve SLT

·

TCM


- DTC stored

MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLT circuit is detected, the TCM interprets this as a fault. The TCM will store the DTC.

WIRING DIAGRAM

C311453E34
1.49,1.729 5.156,1.927 3.667,0.198 10 false Shift Solenoid Valve SLT 5.167,1.135 5.781,1.333 0.615,0.198 10 false SLT+ 5.167,2.125 5.781,2.323 0.615,0.198 10 false SLT- 4.917,2.323 5.094,2.51 0.177,0.188 10 false 19 4.917,1.354 5.083,1.552 0.167,0.198 10 false 20 3.885,1.344 4.5,1.542 0.615,0.198 10 false 14 3.896,2.313 4.51,2.51 0.615,0.198 10 false 6 1.26,1.344 1.875,1.542 0.615,0.198 10 false 2 1.271,2.125 1.885,2.323 0.615,0.198 10 false 1 3.469,1.146 4.083,1.344 0.615,0.198 10 false SLT+ 3.479,2.125 4.094,2.323 0.615,0.198 10 false SLT- 5.75,0.781 6.365,0.979 0.615,0.198 10 false 12 V 1.813,2.719 2.271,2.917 0.458,0.198 10 false C86 1.813,2.906 4.417,3.104 2.604,0.198 10 false Transmission Wire 5.573,3.021 5.885,3.219 0.313,0.198 10 false C77 5.573,3.198 6.031,3.396 0.458,0.198 10 false TCM

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)
a.
C214326C55
1.438,1.323 1.229,1.75 true 1.521,1.104 1.771,1.75 true 1.042,1.771 1.406,1.938 0.365,0.167 10 false SLT+ 0.052,0.021 0.281,0.188 0.229,0.167 10 false *a 1.677,1.771 2.021,1.938 0.344,0.167 10 false SLT-
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
14 (SLT+) - 6 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
14 (SLT+) - Body ground Always 10 kΩ or higher
6 (SLT-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

NG

3.INSPECT SHIFT SOLENOID VALVE SLT
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.
C328831C09
0.802,0.375 1.188,0.646 0.385,0.271 0.844,2.073 1.656,2.833 true 0.708,2.813 0.781,2.073 true 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 0.875,0.438 1.333,0.635 0.458,0.198 10 false C77 0.365,2.865 1.052,3.063 0.688,0.198 10 false 20 (SLT+) 1.521,2.885 2.198,3.073 0.677,0.188 10 false 19 (SLT-)
*a Rear view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C77-20 (SLT+) - C77-19 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
C77-20 (SLT+) - Body ground Always 10 kΩ or higher
C77-19 (SLT-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SLT
a.
C209928C30
1.771,0.969 2.219,0.385 true 1.479,0.958 1.021,0.375 true 1.771,2.948 2.219,2.354 true 1.479,2.948 1.021,2.354 true 0.052,0 0.365,0.198 0.313,0.198 10 false *a 2.25,0.26 2.417,0.458 0.167,0.198 10 false 1 0.917,0.24 1.083,0.438 0.167,0.198 10 false 2 2.24,2.208 2.406,2.406 0.167,0.198 10 false 1 0.917,2.229 1.083,2.427 0.167,0.198 10 false 2 1.927,3.979 2.125,4.177 0.198,0.198 10 false (-) 1.115,3.99 1.333,4.188 0.219,0.198 10 false (+)
*a Component without harness connected
(Shift Solenoid Valve SLT)


Remove shift solenoid valve SLT.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 -2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 2

·

Battery negative (-) → Terminal 1


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

NG