Home › Drivetrain › RC60F / RC61F MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSMISSION UNIT › 2015.06–2016.03
RM3250E _52 Drivetrain _038036 RC60F / RC61F MANUAL TRANSMISSION / TRANSAXLE _0200052 MANUAL TRANSMISSION UNIT A

RC60F / RC61F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION UNIT  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STRAIGHT PIN AND RING PIN

NOTICE:

It is not necessary to remove a straight pin and ring pin unless it is being replaced.


a.
C324156C01
0.344,0.24 0.656,0.396 0.313,0.156 10 false *a 2.75,0.188 3.063,0.344 0.313,0.156 10 false *a 0.469,2.646 0.781,2.802 0.313,0.156 10 false *a 3.146,2.5 3.396,2.656 0.25,0.156 10 false *a 1.188,0.625 1.344,0.823 0.156,0.198 10 false A 2.146,0.635 2.302,0.833 0.156,0.198 10 false A 1.979,2.708 2.135,2.906 0.156,0.198 10 true B 2.802,1.656 2.958,1.854 0.156,0.198 10 false B
*a Protrusion Height


Using a plastic-faced hammer, tap 2 new straight pins and 2 new ring pins into the rear transmission case sub-assembly.

Specified Condition:
Item Specified Condition
A 5.5 to 6.5 mm (0.2166 to 0.2559 in.)
B 3.5 to 4.5 mm (0.1378 to 0.1771 in.)



b.
C324155C01
0.323,1.302 0.635,1.458 0.313,0.156 10 false *a 0.313,1.865 0.625,2.021 0.313,0.156 10 false *a 3,0.094 3.313,0.25 0.313,0.156 10 false *a 3.031,0.677 3.344,0.833 0.313,0.156 10 false *a 0.385,0.99 0.542,1.188 0.156,0.198 10 false A 2.969,0.969 3.125,1.167 0.156,0.198 10 false A
*a Protrusion Height


Using a plastic-faced hammer, tap 4 new ring pins into the intermediate plate.

Specified Condition:
Item Specified Condition
A 5.5 to 7.5 mm (0.2166 to 0.2952 in.)



c.
C324154C01
2.906,1.188 3.219,1.344 0.313,0.156 10 false *a 1.583,0.063 1.74,0.26 0.156,0.198 10 true A 1.792,1.385 1.948,1.583 0.156,0.198 10 true A 0.344,0.135 0.656,0.292 0.313,0.156 10 false *a
*a Protrusion Height


Using a plastic-faced hammer, tap 2 new straight pins into the front transmission case sub-assembly.

Specified Condition:
Item Specified Condition
A 9.5 to 10.5 mm (0.3741 to 0.4133 in.)



Hide 33244D 2.INSTALL NO. 3 GEAR SHIFT FORK SHAFT

a.
C336112

Install the No. 3 gear shift fork to the No. 3 gear shift fork shaft with a new bolt.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:

Secure the shift fork with the bolt from the side as shown in the illustration.



Hide 33242 3.INSTALL NO. 1 GEAR SHIFT FORK SHAFT

a.
C336972

Pass the No. 1 gear shift fork shaft through the No. 1 gear shift fork head, set the shaft on the cloth that was placed on the 2 V-blocks, and then hold the shaft in place as shown in the illustration.

CAUTION:
·

Make sure to perform this procedure with 2 people and firmly hold the gear shift fork shaft in place.

·

Make sure to protect the gear shift fork shaft with a cloth before performing this procedure. If the gear shift fork shaft is damaged, shifting operations will worsen.




b.

Using a 5 mm pin punch and hammer, tap a new slotted pin into the No. 1 gear shift head and No. 1 gear shift fork shaft.

Standard depth:

0 to 0.5 mm (0 to 0.0196 in.)


NOTICE:

Secure the gear shift head with the new slotted pin from the side as shown in the illustration.



c.
C336113

Install the No. 1 gear shift fork to the No. 1 gear shift fork shaft with a new bolt.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:

Secure the shift fork with the bolt from the side as shown in the illustration.



Hide 33245G 4.INSTALL NO. 4 GEAR SHIFT FORK SHAFT

a.
C336970

Pass the No. 4 gear shift fork shaft through the No. 4 gear shift fork head, set the shaft on the cloth that was placed on the 2 V-blocks, and then hold the shaft in place as shown in the illustration.

CAUTION:
·

Make sure to perform this procedure with 2 people and firmly hold the gear shift fork shaft in place.

·

Make sure to protect the gear shift fork shaft with a cloth before performing this procedure. If the gear shift fork shaft is damaged, shifting operations will worsen.




b.

Using a 5 mm pin punch and hammer, tap a new slotted pin into the No. 4 gear shift head and No. 4 gear shift fork shaft.

Standard depth:

0 to 0.5 mm (0 to 0.0196 in.)


NOTICE:

Secure the gear shift head with the new slotted pin from the side as shown in the illustration.



c.
C336114

Install the No. 4 gear shift fork shaft to the No. 1 gear shift fork.


Hide 33243A 5.INSTALL NO. 2 GEAR SHIFT FORK SHAFT

a.
C336974

Pass the No. 2 gear shift fork shaft through the No. 2 gear shift fork head, set the shaft on the cloth that was placed on the 2 V-blocks, and then hold the shaft in place as shown in the illustration.

CAUTION:
·

Make sure to perform this procedure with 2 people and firmly hold the gear shift fork shaft in place.

·

Make sure to protect the gear shift fork shaft with a cloth before performing this procedure. If the gear shift fork shaft is damaged, shifting operations will worsen.




b.

Using a 5 mm pin punch and hammer, tap a new slotted pin into the No. 2 gear shift head and No. 2 gear shift fork shaft.

Standard depth:

0 to 0.5 mm (0 to 0.0196 in.)


NOTICE:

Secure the gear shift head with the new slotted pin from the side as shown in the illustration.



c.
C336115

Install the No. 2 gear shift fork shaft to the No. 1 gear shift fork head.


d.
C336111

Install the No. 2 gear shift fork to the No. 2 gear shift fork shaft with a new bolt.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:

Secure the shift fork with the bolt from the side as shown in the illustration.



Hide 33243G 6.INSTALL NEEDLE ROLLER BEARING

a.
C329815C01
1.938,0.604 2.333,1.052 true 1.969,1.073 2.26,1.208 false 1.104,2.01 0.594,1.469 0.594,1.469 1.125,1.615 false 1.135,2.99 0.458,3.125 0.458,3.125 0.521,2.833 true 1.74,0.51 2.052,0.667 0.313,0.156 10 false *1 1.781,0.99 2.094,1.146 0.313,0.156 10 false *2 3.198,0.865 3.354,1.063 0.156,0.198 10 false A 0.26,1.354 0.719,1.552 0.458,0.198 10 false SST 0.146,3.094 0.604,3.292 0.458,0.198 10 false SST
*1 Needle Roller Bearing
*2 Shift Arm


Using SST and a press, install a new needle roller bearing into the shift arm so that dimension A in the illustration is as specified.

SST
09950-60010  (09951-00220)
09950-70010  (09951-07100)
09527-20011  

Dimension A:

0.5 to 1.5 mm (0.0197 to 0.0591 in.)


NOTICE:
C338343C01
1.906,1.604 2.271,1.073 2.271,1.073 2.521,1.073 false 2.604,1.01 2.917,1.167 0.313,0.156 10 false *1
*1 Engraved Surface
V100135

Press


Press the engraved surface to install the bearing.



Hide 33206 7.INSTALL SHIFT INTERLOCK PLATE SUB-ASSEMBLY

a.
C323886C01
1.667,0.625 2.479,0.354 false 0.573,2.906 1.125,2.708 false 0.479,1.99 0.281,1.677 false 2.594,0.24 2.906,0.396 0.313,0.156 10 false *1 0.333,2.865 0.646,3.021 0.313,0.156 10 false *2 0.094,1.552 0.406,1.708 0.313,0.156 10 false *3
*1 Shift Interlock Plate Sub-assembly
*2 Shift Arm Pivot
*3 Shift Arm


Coat the shift fork shaft bearing with gear oil, and then install the shift arm and shift arm pivot to the shift interlock plate sub-assembly.


b.
C323887

Install a new snap ring to the shift arm pivot


Hide 33261C 8.INSTALL SHIFT AND SELECT LEVER SHAFT

a.
C336116C01
1.365,0.438 1.49,0.313 1.49,0.313 1.646,0.313 false 1.969,0.979 2.094,0.854 2.094,0.854 2.25,0.854 false 2.708,1.5 2.833,1.375 2.833,1.375 2.99,1.375 false 1.677,0.24 1.99,0.396 0.313,0.156 10 false *1 2.271,0.792 2.583,0.948 0.313,0.156 10 false *2 3.042,1.302 3.354,1.458 0.313,0.156 10 false *3
*1 Inner Select Lever
*2 Select Return Compression Spring
*3 No. 2 Lock Ball Pin


Coat the No. 2 lock ball pin with the gear oil.


b.

Install the No. 2 lock ball pin and select return compression spring to the inner select lever.


c.
C323890

Install the shift and select cam to the inner select lever.


d.
C336677

Align the inner select lever with the shift interlock plate sub-assembly, and then insert the inner select lever.


e.
C336664

Install the shift and select shaft to the shift interlock plate and inner select lever.


f.
C338344

Using a 5 mm pin punch and hammer, tap a new slotted pin into the inner select lever and shift and select lever shaft.

Standard Depth:

0 to 0.5 mm (0 to 0.0196 in.)


NOTICE:

Face the shaft groove towards the shift and select cam, and then tap in the pin as shown in the illustration.



g.
C323892

Install a new bolt.

Torque:
50.1 N*m (511 kgf*cm, 37 ft.*lbf)


h.
C323888

Install a new e-ring to the shift and select lever shaft.


i.

Check that shaft operates smoothly.


Hide 33242L 9.INSTALL SHIFT FORK SHAFT BEARING

a.
C336118N01
0.677,3.167 0.469,3.167 0.469,3.167 0.615,3.469 false 2.781,3.104 2.938,3.302 0.156,0.198 10 false A 0.146,3.063 0.469,3.26 0.323,0.198 10 false SST

Using SST and a hammer, tap 2 new shift fork shaft bearings (front side) into the front transmission case sub-assembly so that dimension A in the illustration is as specified.

SST
09950-70010  (09951-07360)
09950-60010  (09951-00180)

Dimension A:

147.7 to 148.7 mm (5.815 to 5.854 in.)


NOTICE:
C338345C02
1.917,1.604 2.302,1.01 2.302,1.01 2.604,1.01 false 2.656,0.917 2.969,1.073 0.313,0.156 10 false *1
*1 Engraved Surface
V100135

Press


Press the engraved surface to install the bearing.



Hide 33261K 10.INSTALL SHIFT AND SELECT LEVER SHAFT NEEDLE ROLLER BEARING

a.
C323897N02
0.458,0.688 0.635,0.885 0.177,0.198 10 false A

Using SST and a hammer, tap a new shift and select lever shaft needle roller bearing (front side) into the front transmission case sub-assembly so that dimension A in the illustration is as specified.

SST
09950-70010  (09951-07360)
09950-60010  (09951-00230)

Dimension A:

0.5 to 1.5 mm (0.0197 to 0.0590 in.)


NOTICE:
C338346C02
1.896,1.615 2.302,1.083 2.302,1.083 2.615,1.083 false 2.667,1.021 2.979,1.177 0.313,0.156 10 false *1
*1 Engraved Surface
V100135

Press


Press the engraved surface to install the bearing.



Hide 33242L 11.INSTALL SHIFT FORK SHAFT BEARING

a.
C336119N01
0.542,3.417 0.417,3.135 0.417,3.135 0.615,3.135 false 0.094,3.042 0.406,3.24 0.313,0.198 10 false SST 2.438,2.99 2.75,3.188 0.313,0.198 10 false A

Using SST and a hammer, tap 2 new shift fork shaft bearings (rear side) into the rear transmission case sub-assembly so that dimension A in the illustration is as specified.

SST
09950-70010  (09951-07360)
09950-60010  (09951-00180)

Dimension A:

106.9 to 107.9 mm (4.209 to 4.248 in.)


NOTICE:
C338347C01
1.917,1.615 2.385,1.01 2.385,1.01 2.698,1.01 true 2.781,0.948 3.094,1.104 0.313,0.156 10 true *1
*1 Engraved Surface


Press the engraved surface to install the bearing.



Hide 33261K 12.INSTALL SHIFT AND SELECT LEVER SHAFT NEEDLE ROLLER BEARING

a.
C336121N01
0.708,2.177 0.417,3.208 0.417,3.208 0.76,3.052 true 1.875,3.01 2.031,3.208 0.156,0.198 10 false A 0.104,3.25 0.438,3.458 0.333,0.208 10 true SST

Using SST and a hammer, tap a new shift and select lever shaft needle roller bearing (rear side) into the rear transmission case sub-assembly so that dimension A in the illustration is as specified.

SST
09950-70010  (09951-07200)
09950-60010  (09951-00230)

Dimension A:

107.15 to 108.15 mm (4.219 to 4.257 in.)


NOTICE:
C338349C01
1.917,1.625 2.323,1.01 2.323,1.01 2.677,1.01 true 2.75,0.938 3.063,1.094 0.313,0.156 10 false *1
*1 Engraved Surface


Press the engraved surface to install the bearing.



Hide 33111C 13.INSTALL TRANSMISSION CASE PLUG

a.
C336122N01
0.646,2.417 0.354,1.073 0.354,1.073 0.698,1.969 true 1.813,1.573 1.969,1.771 0.156,0.198 10 false A 0.052,0.938 0.438,1.135 0.385,0.198 10 false SST

Using SST and a hammer, tap a new transmission case plug into the rear transmission case sub-assembly so that dimension A in the illustration is as specified.

SST
09950-70010  (09951-07200)
09950-60010  (09951-00230)

Dimension A:

17.3 to 18.3 mm (0.6812 to 0.7204 in.)



Hide 33411H 14.INSTALL REAR COUNTER GEAR BEARING OR ROLLER

a.
C323997N01
2.667,1.25 2.854,1.25 2.854,1.25 2.781,1.677 false 2.896,1.146 3.354,1.344 0.458,0.198 10 false SST

Coat a new rear counter gear bearing or roller (outer race) with gear oil, and then using SST and a press, install it to the rear transmission case.

SST
09950-70010  (09951-07360)
09950-60010  (09951-00710)


b.
C323842

Install the bolt and bearing lock plate.

Torque:
11.3 N*m (115 kgf*cm, 8 ft.*lbf)


Hide 33321N 15.INSTALL FRONT OUTPUT SHAFT BEARING

a.
C324000N01
0.583,1.333 0.458,1.021 0.458,1.021 0.698,1.021 false 0.125,0.906 0.583,1.104 0.458,0.198 10 false SST

Using SST and a hammer, install a new tapered front output shaft bearing (outer race) to the rear transmission case sub-assembly.

SST
09950-70010  (09951-07200)
09951-00850  


Hide 33321A 16.INSTALL REAR OUTPUT SHAFT BEARING

a.
C324001N01
0.865,1.688 1.156,1.688 1.156,1.688 1.01,2.115 false 1.229,1.604 1.688,1.802 0.458,0.198 10 false SST

Using SST and a hammer, install a new rear output shaft bearing (outer race) to the rear transmission case sub-assembly.

SST
09950-70010  (09951-07100)
09950-60020  (09951-00790)


Hide 33321N 17.INSTALL FRONT OUTPUT SHAFT BEARING

Hide 18.INSPECT PRELOAD

a.
C324019C01
1.906,0.208 2.635,0.208 false 1.927,0.635 2.667,0.635 true 1.938,1.74 2.677,1.74 true 1.917,2.25 2.677,2.25 false 2.698,0.146 3.01,0.302 0.313,0.156 10 false *1 2.729,0.563 3.042,0.719 0.313,0.156 10 false *2 2.771,1.688 3.083,1.844 0.313,0.156 10 false *3 2.76,2.177 3.073,2.333 0.313,0.156 10 false *4
*1 Manual Transmission Output Shaft Rear Set Nut
*2 Rear Output Shaft Bearing
*3 Output Shaft Spacer
*4 Rear Output Shaft Bearing Shim


Temporarily install the output shaft, rear output shaft bearing shim, output shaft spacer, rear output shaft bearing and a new manual transmission output shaft rear set nut to the rear transmission case sub-assembly.

NOTICE:
·

Do not apply gear oil to a new output shaft bearing and rear output shaft bearing. If applied, the turning torque cannot be accurately measured.

·

If the turning torque is not properly measured, the output shaft bearing may generate abnormal noise and become damaged.




b.
C335229C01
2.396,0.677 2.719,0.219 2.719,0.219 2.906,0.219 true 2.99,1.833 2.99,1.625 2.99,1.625 2.302,1.156 true 1.125,1.604 1.344,1.813 0.219,0.208 10 false *b 0.208,0.49 0.521,0.688 0.313,0.198 10 false *a 2.948,0.146 3.271,0.344 0.323,0.198 10 false SST 2.865,1.875 3.188,2.073 0.323,0.198 10 false SST
*a Hold
*b Turn


Temporarily install the manual transmission output shaft rear set nut to the output shaft.

SST
09326-71010  09326-71030  

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)

NOTICE:

If the nut is not temporarily installed, the position of the rear output shaft bearing will be unstable causing the preload to be unstable.



c.
C329003C01
2.344,0.75 2.677,0.24 2.677,0.24 2.833,0.24 true 3.073,1.76 3.073,1.604 3.073,1.604 2.271,1.25 true 0.552,0.156 0.771,0.354 0.219,0.198 10 false *a 0.135,1.542 0.354,1.729 0.219,0.188 10 false *b 0.823,0.667 1.01,0.875 0.188,0.208 10 false *c 2.885,0.156 3.229,0.354 0.344,0.198 10 false SST 2.948,1.781 3.292,1.979 0.344,0.198 10 false SST
*a Hold
*b Turn
*c Fulcrum Length


Using SST and a torque wrench, tighten the manual transmission output shaft rear set nut.

SST
09326-71010  09326-71030  

Torque:
Specified tightening torque : 187 N*m (1907 kgf*cm, 138 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 50 mm (1.9685 in.)) + torque wrench (fulcrum length of 1055 mm (41.5354 in.)): 178.5 N*m (1820 kgf*cm, 132 ft.*lbf)




d.
C329004C01
0.802,1.115 1.698,1.115 true 0.49,1.042 0.802,1.229 0.313,0.188 10 false SST 1.385,0.073 1.573,0.26 0.188,0.188 10 false *a
*a Fulcrum Length


Using SST and a torque wrench, measure the turning torque of the output shaft bearing while rotating SST at 60 rpm.

Standard turning torque at 60 rpm:
New output shaft bearing:

0.21 to 1.32 N*m (2.14 to 13.46 kgf*cm, 1.86 to 11.68 in.*lbf)


NOTICE:
·

Do not apply gear oil to a new output shaft bearing and rear output shaft bearing. If applied, the turning torque cannot be accurately measured.

·

If the turning torque is not properly measured, the output shaft bearing may generate abnormal noise and become damaged.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

New output shaft bearing:

When using SST (fulcrum length of 50 mm (1.969 in.)) + torque wrench (fulcrum length of 160 mm (6.299 in.)): 0.16 to 1.00 N*m (1.64 to 10.19 kgf*cm, 1.42 to 8.85 in.*lbf)



If the torque is more than the standard, replace the output shaft shim.

HINT:

New output shaft bearing:

When the thickness of the shim is increased by 0.016 mm (0.0006 in.), the preload is reduced by 0.45 N*m (4.59 kgf*cm, 3.98 in.*lbf).


Standard Shim Thickness:
Part No. Mark Thickness Part No. Mark Thickness
90564-T0020 01 2.214 to 2.230 mm (0.0872 to 0.0877 in.) 90564-T0044 25 2.598 to 2.614 mm (0.1023 to 0.1029 in.)
90564-T0021 02 2.230 to 2.246 mm (0.0878 to 0.0884 in.) 90564-T0045 26 2.614 to 2.630 mm (0.1030 to 0.1035 in.)
90564-T0022 03 2.246 to 2.262 mm (0.0885 to 0.0890 in.) 90564-T0046 27 2.630 to 2.646 mm (0.1036 to 0.1041 in.)
90564-T0023 04 2.262 to 2.278 mm (0.0891 to 0.0896 in.) 90564-T0047 28 2.646 to 2.662 mm (0.1042 to 0.1048 in.)
90564-T0024 05 2.278 to 2.294 mm (0.0897 to 0.0903 in.) 90564-T0048 29 2.662 to 2.678 mm (0.1049 to 0.1054 in.)
90564-T0025 06 2.294 to 2.310 mm (0.0904 to 0.0909 in.) 90564-T0049 30 2.678 to 2.694 mm (0.1055 to 0.1060 in.)
90564-T0026 07 2.310 to 2.326 mm (0.0910 to 0.0915 in.) 90564-T0050 31 2.694 to 2.710 mm (0.1061 to 0.1066 in.)
90564-T0027 08 2.326 to 2.342 mm (0.0916 to 0.0922 in.) 90564-T0051 32 2.710 to 2.726 mm (0.1067 to 0.1073 in.)
90564-T0028 09 2.342 to 2.358 mm (0.0923 to 0.0928 in.) 90564-T0052 33 2.726 to 2.742 mm (0.1074 to 0.1079 in.)
90564-T0029 10 2.358 to 2.374 mm (0.0929 to 0.0934 in.) 90564-T0053 34 2.742 to 2.758 mm (0.1080 to 0.1085 in.)
90564-T0030 11 2.374 to 2.390 mm (0.0935 to 0.0940 in.) 90564-T0054 35 2.758 to 2.774 mm (0.1086 to 0.1092 in.)
90564-T0031 12 2.390 to 2.406 mm (0.0941 to 0.0947 in.) 90564-T0055 36 2.774 to 2.790 mm (0.1093 to 0.1098 in.)
90564-T0032 13 2.406 to 2.422 mm (0.0948 to 0.0953 in.) 90564-T0056 37 2.790 to 2.806 mm (0.1099 to 0.1104 in.)
90564-T0033 14 2.422 to 2.438 mm (0.0954 to 0.0959 in.) 90564-T0057 38 2.806 to 2.822 mm (0.1105 to 0.1111 in.)
90564-T0034 15 2.438 to 2.454 mm (0.0960 to 0.0966 in.) 90564-T0058 39 2.822 to 2.838 mm (0.1112 to 0.1117 in.)
90564-T0035 16 2.454 to 2.470 mm (0.0967 to 0.0972 in.) 90564-T0059 40 2.838 to 2.854 mm (0.1118 to 0.1123 in.)
90564-T0036 17 2.470 to 2.486 mm (0.0973 to 0.0978 in.) 90564-T0060 41 2.854 to 2.870 mm (0.1124 to 0.1129 in.)
90564-T0037 18 2.486 to 2.502 mm (0.0979 to 0.0985 in.) 90564-T0061 42 2.870 to 2.886 mm (0.1130 to 0.1136 in.)
90564-T0038 19 2.502 to 2.518 mm (0.0986 to 0.0991 in.) 90564-T0062 43 2.886 to 2.902 mm (0.1137 to 0.1142 in.)
90564-T0039 20 2.518 to 2.534 mm (0.0992 to 0.0997 in.) 90564-T0063 44 2.902 to 2.918 mm (0.1143 to 0.1148 in.)
90564-T0040 21 2.534 to 2.550 mm (0.0998 to 0.1003 in.) 90564-T0064 45 2.918 to 2.934 mm (0.1149 to 0.1155 in.)
90564-T0041 22 2.550 to 2.566 mm (0.1004 to 0.1010 in.) 90564-T0065 46 2.934 to 2.950 mm (0.1156 to 0.1161 in.)
90564-T0042 23 2.566 to 2.582 mm (0.1011 to 0.1016 in.) 90564-T0066 47 2.950 to 2.966 mm (0.1162 to 0.1167 in.)
90564-T0043 24 2.582 to 2.598 mm (0.1017 to 0.1022 in.) - - -



Hide 33421 19.INSTALL COUNTER GEAR

a.
C338350

Install the counter gear to SST.

SST
09310-71010  


Hide 33311 20.INSTALL INPUT SHAFT

a.
C338351

Install the input shaft to SST.

SST
09310-71010  


Hide 33369B 21.INSTALL NO. 4 SYNCHRONIZER RING

a.

Coat the No. 4 synchronizer ring with the gear oil.


b.
C336124C01
1.771,0.896 2.115,1 2.115,1 2.406,1 false 1.792,1.667 2.115,1.281 2.115,1.281 2.406,1.281 true 2.479,0.927 2.792,1.083 0.313,0.156 10 false *a 2.49,1.188 2.802,1.344 0.313,0.156 10 false *b
*a Protrusion
*b Groove


Install the No. 4 synchronizer ring to the transmission unit.

HINT:

Align the protrusion of the No. 4 synchronizer ring with the groove of the No. 2 transmission clutch hub



Hide 33311D 22.INSTALL INPUT SHAFT BEARING

a.

Coat the input shaft bearing with the gear oil.


b.
C336106

Install the input shaft bearing to the transmission unit.


Hide 33321 23.INSTALL OUTPUT SHAFT

a.
C336126C01
0,0 0,0 false
V100135

Gear Oil


Coat the output shaft with the gear oil as shown in the illustration.


b.

Install the output shaft to the transmission unit.


c.
C336123N01
2.073,1.938 2.375,1.75 2.375,1.75 2.625,1.75 false 2.719,1.667 3.177,1.865 0.458,0.198 10 false SST

Contract SST and connect the input shaft to the counter gear.


Hide 24.INSTALL SHIFT FORK AND SHIFT FORK SHAFT ASSEMBLY

a.
C333999C01
0,0 0,0 false
V113147

Install in this direction


Move the 2 sleeves shown in the illustration in the direction indicated by the arrows


b.
C338341

Temporarily install the No. 4 gear shift fork to the No. 4 gear shift fork shaft.


c.
C333998C01
0.563,1.052 0.76,1.052 0.76,1.052 0.906,1.375 false 0.573,1.844 0.771,1.844 0.771,1.844 0.917,1.729 false 2.844,0.99 2.604,0.99 2.604,0.99 2.229,1.219 true 2.865,1.573 2.625,1.573 2.625,1.573 2.198,1.396 true 0.344,1.01 0.615,1.208 0.271,0.198 10 false *1 0.396,1.781 0.667,1.979 0.271,0.198 10 false *2 2.875,0.896 3.146,1.094 0.271,0.198 10 false *3 2.927,1.51 3.198,1.708 0.271,0.198 10 false *4
*1 No. 1 Gear Shift Fork
*2 No. 4 Gear Shift Fork
*3 No. 1 Transmission Hub Sleeve
*4 No. 4 Transmission Hub Sleeve


Set the No. 1 gear shift fork onto the No. 1 transmission hub sleeve, and the No. 4 gear shift fork onto the No. 4 transmission hub sleeve.

NOTICE:

Do not drop the No. 4 gear shift fork.



d.
C334000C01
2.156,1.458 2.448,1.458 2.448,1.458 2.573,1.042 true 1.927,1.385 2.24,1.583 0.313,0.198 10 false *1
*1 No. 2 Gear Shift Fork
V113147

Install in this direction


Move the part as shown in the illustration and set the No. 2 gear shift fork onto the No. 2 transmission hub sleeve.


e.
C334001C01
2.063,4.135 2.344,4.344 2.344,4.344 2.563,4.344 true 2.208,4.104 2.365,4.344 true 2.354,4.01 2.354,4.344 true 2.656,4.25 2.969,4.448 0.313,0.198 10 false *a
*a Depressions of SST
V113147

Install in this direction


Install the shift fork shaft to the depression of SST.


f.

Install the No. 4 gear shift fork to the No. 4 gear shift fork shaft with a new bolt.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Securely install the No. 4 gear shift fork with a new bolt from the side of the shaft as shown in the illustration.




g.
C333995C02
0,0 0,0 false
V113147

Install in this direction


Install the No. 3 gear shift fork to the No. 3 transmission hub sleeve, and then move it as shown in the illustration.


h.
C333993C01
1.021,4.5 1.313,4.5 1.313,4.5 1.563,4.25 true 0.823,4.406 1.021,4.615 0.198,0.208 10 false *a
*a Depression of SST
V113147

Install in this direction


Install the shift fork shaft to the depression of SST.


Hide 33461 25.INSTALL REVERSE IDLER GEAR

a.
C323806

Coat the reverse idler gear with the gear oil.


b.

Install the reverse idler gear and reverse idler gear bearing to the reverse idler gear shaft.


c.
C324022

Install the No. 2 oil receiver pipe to the reverse idler gear shaft.


Hide 33101 26.INSTALL MANUAL TRANSMISSION CASE SUB-ASSEMBLY

a.
C333737

Install the manual transmission oil separator sub-assembly (rear side) to the transmission unit.


b.
C336102

Install the No. 3 oil receiver pipe to the rear transmission case sub-assembly.


c.
C324011C01
0.438,0.292 1.063,0.448 false 2.438,0.927 2.875,0.927 true 0.24,0.208 0.552,0.365 0.313,0.156 10 false *1 2.948,0.865 3.26,1.021 0.313,0.156 10 false *a
*1 Transmission Inter Plate Sub-assembly
*a Seal Packing


Apply seal packing to the transmission intermediate plate shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Parts must be assembled within 10 minutes of application. Otherwise, the seal packing (FIPG material) must be removed and reapplied.



d.
C325394C01
0.573,1.688 1.052,1.448 false 0.448,0.281 0.979,0.49 false 0.271,0.188 0.583,0.344 0.313,0.156 10 false *1 0.396,1.625 0.708,1.781 0.313,0.156 10 false *a
*1 Manual Transmission Case Sub-assembly
*a Seal Packing


Apply seal packing to the manual transmission case sub-assembly shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Parts must be assembled within 10 minutes of application. Otherwise, the seal packing (FIPG material) must be removed and reapplied.



e.
C336127C01
0.406,2.958 0.76,2.958 true 0.219,2.875 0.531,3.073 0.313,0.198 10 false *a
*a Tape Application Prohibited


Install the rear transmission case sub-assembly and intermediate plate.

NOTICE:
·

Secure the rear transmission case sub-assembly and intermediate plate with tape.

·

Make sure that the tape does not contact the seal packing application surface of the manual transmission case sub-assembly.




f.
C323825

Install the rear transmission case sub-assembly.


g.
C338688

Install the rear output shaft bearing to the transmission unit.


h.
C338689

Temporarily install the manual transmission output shaft rear set nut to the transmission unit.


i.
C334021C02
0.125,0.698 0.438,0.854 0.313,0.156 10 false *a 1.094,1.896 1.406,2.052 0.313,0.156 10 false *b
*a Hold
*b Turn


Temporarily install the manual transmission output shaft rear set nut.

SST
09326-71010  09326-71030  

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)

CAUTION:

Since the manual transmission unit is very heavy, perform these procedures with 2 people.


NOTICE:

If the nut is not temporarily installed, the position of the rear output shaft will be unstable causing the preload to be unstable.



j.
C336128

Lay the transmission unit on its side, and then remove SST from the transmission unit as shown in the illustration.

SST
09310-71010  

CAUTION:

Since the manual transmission unit is very heavy, perform these procedures with 2 people.


NOTICE:

Lay the transmission unit on its side so that the shift fork shaft sub-assembly is on the bottom.



k.
C333991

Install the transmission magnet.


l.
C323835

Install the transmission oil separator sub-assembly (front side) to the transmission unit with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

CAUTION:

Since the manual transmission unit is very heavy, perform these procedures with 2 people.



m.
C336101

Install the shift interlock plate stopper to the transmission unit with the 2 bolts.

Torque:
23.8 N*m (243 kgf*cm, 18 ft.*lbf)

CAUTION:

Since the manual transmission unit is very heavy, perform these procedures with 2 people.



n.
C334785C01
0.625,1.156 0.417,0.813 0.417,0.813 0.833,1.031 false 0.188,0.688 0.5,0.885 0.313,0.198 10 false *a
*a Wooden Block


Use wooden blocks or other objects to support the corners of the transmission unit as shown in the illustration before conducting work.


o.
C336100

Install the shift and select lever shaft sub-assembly to the transmission unit.

CAUTION:

Since the manual transmission unit is very heavy, perform these procedures with 2 people.



p.
C334786

Align the groove of the shift and select cam with the reverse idler shaft, and then install the reverse idler gear.

CAUTION:

Since the manual transmission unit is very heavy, perform these procedures with 2 people.



q.
C323804

Install the manual transmission case sub-assembly with the 12 bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)

CAUTION:

Since the manual transmission unit is very heavy, perform these procedures with 2 people.



r.
C323802

Install the reverse idler gear shaft bolt and a new gasket to the reverse idler gear shaft.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

CAUTION:

Since the manual transmission unit is very heavy, perform these procedures with 2 people.



Hide 33311T 27.INSTALL INPUT SHAFT SHAFT SNAP RING

a.
C323800

Using snap ring pliers, install a new input shaft shaft snap ring.


Hide 33311G 28.INSTALL FRONT BEARING SHAFT SNAP RING

a.
C323801

Using a snap ring expander, install a new front bearing shaft snap ring.


Hide 33411E 29.INSTALL COUNTER GEAR SHAFT NUT

a.
C334265C01
2.094,3.646 2.458,4.375 2.458,4.375 2.688,4.375 true 1.021,2.396 1.177,2.396 1.177,2.396 1.698,3.313 true 2.74,4.302 3.042,4.479 0.302,0.177 10 false SST 0.708,2.323 1.01,2.5 0.302,0.177 10 false SST 0.51,0.458 0.823,0.615 0.313,0.156 10 false *a 2.833,2.594 3.146,2.75 0.313,0.156 10 false *b
*a Turn
*b Hold


Using SST, secure the output shaft.

SST
09326-35010  (09326-03010)

SST
09326-71030  


b.

Using a 41 mm socket wrench, install a new counter gear shaft nut.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

CAUTION:

Since the manual transmission unit is very heavy, perform these procedures with 2 people.



c.
C323798

Using a chisel and hammer, stake the counter gear shaft nut.


d.
C334163C01
2.396,1.365 2.51,1.531 0.115,0.167 10 false -
V100135

Push


Push in the input shaft and counter gear so that the 2 snap rings are firmly pressed into the transmission case.


Hide 33131A 30.INSTALL FRONT TRANSMISSION BEARING RETAINER OIL SEAL

Hide 33131D 31.INSTALL FRONT BEARING RETAINER

a.
C337077C01
2.333,0.75 2.583,0.375 2.583,0.375 2.833,0.375 true 2.458,1.729 2.708,1.354 2.708,1.354 2.958,1.354 true 0.323,3.583 0.51,3.813 0.188,0.229 10 true *a 1.771,3.563 1.958,3.76 0.188,0.198 10 true *b 2.917,0.271 3.229,0.427 0.313,0.156 10 false *c 2.99,1.26 3.302,1.417 0.313,0.156 10 false *1
*1 Front Bearing Retainer
*a Incorrect
*b Correct
*c Seal Packing


Apply seal packing to the front bearing retainer shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Parts must be assembled within 10 minutes of application. Otherwise, the seal packing (FIPG material) must be removed and reapplied.



b.
C336129C01
2.292,1.198 2.969,1.333 2.969,1.333 2.167,1.75 true 0.896,0.781 1.292,0.594 1.292,0.594 0.813,1.344 true 1.302,0.427 1.552,0.635 0.25,0.208 10 false *a 3.042,1.25 3.229,1.427 0.188,0.177 10 false *b
*a Protrusion
*b Groove


Install the No. 1 oil receiver pipe to the front bearing retainer.

HINT:

Align the protrusion of the No. 1 oil receiver pipe with the groove of the front bearing retainer.



c.
C323797

Install the front bearing retainer to the front transmission case with new 11 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

CAUTION:

Since the manual transmission unit is very heavy, perform these procedures with 2 people.



Hide 31111 32.INSTALL CLUTCH HOUSING

a.
C323803

Install the clutch housing to the manual transmission case sub-assembly with the 10 bolts.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)

CAUTION:

Since the manual transmission unit is very heavy, perform these procedures with 2 people.



Hide 33321G 33.TIGHTEN MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT

CAUTION:

Since the manual transmission unit is very heavy, perform these procedures with 2 people.


a.
C323512C02
2.927,0.583 2.927,0.396 false 2.448,0.906 2.594,1.094 2.594,1.094 2.771,1.094 false 0.438,1.573 0.563,1.573 0.563,1.573 0.563,1.958 false 1.542,2.469 2.74,3.073 2.74,3.073 2.927,3.073 true 0.417,3.25 0.5,3.25 0.5,3.25 0.74,3.833 true 2.823,0.188 3.135,0.344 0.313,0.156 10 false *1 2.99,3.01 3.146,3.208 0.156,0.198 10 true A 0.094,1.49 0.552,1.688 0.458,0.198 10 false SST 2.833,1.01 2.99,1.208 0.156,0.198 10 true A 0.083,3.167 0.542,3.365 0.458,0.198 10 false SST
*1 Input Shaft


Engage the gear, and then secure the input shaft using SST.

SST
09322-35010  (09322-03010, 09322-03020, 09322-03030, 90105-12087, 90170-12030, 94622-51200)

HINT:
·

Install SST securely so that the part labeled A is in-line with the input shaft.

·

Make sure that the part labeled A moves back and forth by hand after installing SST.




b.
C337519N01
2.635,1.802 2.323,1.802 2.323,1.802 1.813,1.417 true 2.719,1.729 3.177,1.927 0.458,0.198 10 false SST

Using an L-type handle and SST, install the manual transmission output shaft rear set nut to the output shaft sub-assembly.

SST
09326-35010  (09326-03010)

Torque:
187 N*m (1907 kgf*cm, 138 ft.*lbf)


Hide 33321G 34.STAKE MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT

a.
C323791

Using a chisel and hammer, stake the manual transmission output shaft rear set nut.


Hide 33121G 35.INSTALL MANUAL TRANSMISSION CASE COVER

a.
C324146C01
0.396,0.302 0.969,0.542 false 0.479,1.115 0.948,1.115 true 0.208,0.208 0.521,0.365 0.313,0.156 10 false *1 0.271,1.021 0.583,1.177 0.313,0.156 10 false *a
*1 Manual Transmission Case Cover
*a Seal Packing


Apply seal packing to the manual transmission case cover shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Parts must be assembled within 10 minutes of application. Otherwise, the seal packing (FIPG material) must be removed and reapplied.



b.
C323511

Install the manual transmission case cover to the rear transmission case with the 4 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 33521 36.INSTALL SHIFT LEVER HOUSING

a.
C323504

Install a new bolt and shift lever housing.

Torque:
50.1 N*m (511 kgf*cm, 37 ft.*lbf)

NOTICE:

Do not damage the sealing surface of the control shift lever retainer sub-assembly



Hide 33506F 37.INSTALL FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

CAUTION:

Since the manual transmission unit is very heavy, perform these procedures with 2 people.


a.
C325396C01
0.385,0.802 1.24,0.802 true 2.146,1.802 1.375,1.146 true 0.479,0.219 0.844,0.479 true 2.042,0.698 2.729,1.24 true 0.208,0.74 0.521,0.896 0.313,0.156 10 false *1 2.198,1.813 2.51,1.969 0.313,0.156 10 false *2 0.271,0.115 0.583,0.313 0.313,0.198 10 false *3 2.781,1.281 3.094,1.479 0.313,0.198 10 false *3
*1 Inner Shift Lever
*2 Shift Lever Housing
*3 Control Shift Lever Shaft
V100135

MP grease
V100136

Gear oil


Apply MP grease to the tip of the inner shift lever.


b.

Apply gear oil to the control shift lever shaft.


c.

Install the control shift lever retainer assembly and a new control shift lever retainer gasket on the extension housing sub-assembly, making sure that the inner shift lever is properly set on the shift lever housing.


d.
C323502

Install the floor shift control shift lever retainer sub-assembly to the extension housing sub-assembly with the 4 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 33292A 38.INSTALL LOCK BALL PIN

a.
C323793

Install the lock ball pin and compression spring to the rear transmission case.


b.

Using a 10 mm hexagon wrench, install a new No. 2 with head straight screw plug to the rear transmission case.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 33275B 39.INSTALL SHAFT DETENT BALL

a.
C339096

Install the 4 shaft detent balls and 4 shift detent ball compression springs to the rear transmission case.


b.

Using a 6 mm hexagon wrench, install 4 new shift detent ball plugs to the rear transmission case.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


Hide 33111A 40.INSTALL MANUAL TRANSMISSION CASE PLUG

a.
C336098

Install a new gasket and the manual transmission filler plug (with label).

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


b.

Install a new gasket and the drain plug sub-assembly (without label).

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


c.

Using a 10 hexagon wrench, install a new gasket and the straight screw plug with head.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 89413B 41.INSTALL TRANSMISSION REVOLUTION SENSOR (w/ Intelligent Manual Transmission Switch)

Hide 42.INSTALL BACK-UP LIGHT SWITCH BRACKET

a.
C333523

Install the 3 back-up light switch brackets with the 3 bolts.

Torque:
12.6 N*m (128 kgf*cm, 9 ft.*lbf)


Hide 31236B 44.INSTALL RELEASE FORK SUPPORT

Hide 31230 45.INSTALL CLUTCH RELEASE BEARING ASSEMBLY