Home › Engine / Hybrid System › 5L-E FUEL › FUEL INJECTION NOZZLE › from 2016.01
RM3250E _51 Engine / Hybrid System _049912 5L-E FUEL _0242564 FUEL INJECTION NOZZLE A

5L-E FUEL  FUEL INJECTION NOZZLE  INSTALLATION  


PROCEDURE

Hide 23600 1.INSTALL NOZZLE HOLDER AND NOZZLE SET

a.

Install 4 new injection nozzle seat gaskets and the 4 injection nozzle seats to the injection nozzle holes of the cylinder head sub-assembly.


b.
A370274N01
0.583,0.938 0.854,0.938 0.854,0.938 1.74,1.24 true 0.26,0.844 0.615,1.063 0.354,0.219 10 false SST

Using SST, install the 4 nozzle holder and nozzle sets.

SST
09268-64010  (09268-64020)

Torque:
63.7 N*m (650 kgf*cm, 47 ft.*lbf)

NOTICE:
·

Overtightening could cause nozzle deformation and needle adhesion or other defects.

·

When installing the injection nozzle, never tighten the nozzle holder body. Tighten the retaining nut section.



HINT:

Arrange the nozzle holder and nozzle sets in correct order.



Hide 23760 2.INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY

a.

Install 4 new ring packing washers and the nozzle leakage pipe assembly with the 4 ring packing setting nuts.

Torque:
29.5 N*m (301 kgf*cm, 22 ft.*lbf)


b.

Connect the fuel hose to the nozzle leakage pipe assembly, and slide the clamp to secure the hose.


Hide 19871 3.INSTALL NO. 1 GLOW PLUG CONNECTOR

Hide 23701 4.INSTALL INJECTION PIPE SUB-ASSEMBLY

a.
A329093C06
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, install the 4 injection pipe sub-assemblies to the nozzle holder and nozzle set and injection pump assembly with the union nuts.

Torque:
Specified tightening torque : 24.5 N*m (250 kgf*cm, 18 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.181 in.)) + torque wrench (fulcrum length of 180 mm (7.087 in.)): 21 N*m (214 kgf*cm, 15 ft.*lbf)




b.

Install the 2 injection pipe clamps with the 2 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 6.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 7.BLEED AIR FROM FUEL SYSTEM

a.

Move the hand pump on the upper part of the fuel filter assembly up and down and fill the injection pump assembly and fuel system with fuel.


b.

Using a 17 mm union nut wrench, loosen one of the union nuts (on the nozzle holder and nozzle set side).


c.

Crank the engine until fuel comes out from the union nut connection (on the nozzle holder and nozzle set side).


d.
A329093C06
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the union nut (on the nozzle holder and nozzle set side).

Torque:
Specified tightening torque : 24.5 N*m (250 kgf*cm, 18 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.181 in.)) + torque wrench (fulcrum length of 180 mm (7.087 in.)): 21 N*m (214 kgf*cm, 15 ft.*lbf)




e.

Perform the procedures above for each injection pipe sub-assembly.