Home › Engine / Hybrid System › 5L-E LUBRICATION › OIL AND OIL FILTER › from 2016.01
RM3250E _51 Engine / Hybrid System _049916 5L-E LUBRICATION _0244987 OIL AND OIL FILTER A

5L-E LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners or solvents.

·

In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.

·
A339769

To prevent burns, do not remove the oil pan drain plug and oil filter sub-assembly while the engine is hot.



PROCEDURE

Hide 51410 1.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51442 2.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 3.DRAIN ENGINE OIL

CAUTION:

To prevent burns, do not remove the oil pan drain plug while the engine is hot.


a.

Remove the oil filler cap.


b.

Remove the oil pan drain plug and gasket, and then drain the oil into a container.


c.

Clean and install a new gasket and the oil pan drain plug.

Torque:
34.5 N*m (352 kgf*cm, 25 ft.*lbf)


Hide 15601 4.REMOVE OIL FILTER SUB-ASSEMBLY

CAUTION:

To prevent burns, do not remove the oil filter sub-assembly while the engine is hot.


a.
A378281N01
1.448,1.208 0.656,1.208 true 0.302,1.115 0.646,1.302 0.344,0.188 10 true SST

Using SST, remove the oil filter sub-assembly.

SST
09228-44011  

HINT:
·

Before removing the oil filter sub-assembly, place cloth where the oil may splash.

·

Use a container to catch the draining engine oil.




Hide 15601 5.INSTALL OIL FILTER SUB-ASSEMBLY

a.

Check and clean the oil filter sub-assembly installation surface.


b.

Apply clean engine oil to the gasket of a new oil filter sub-assembly.


c.

Install the oil filter sub-assembly and tighten it by hand until the gasket contacts the installation surface.


d.

Using SST, tighten the oil filter sub-assembly. Choose from the following to further tighten the oil filter sub-assembly.

Depending on the space available, choose from the following.

SST
09228-44011  

i.
A378213C01
0.458,0.917 0.594,0.917 0.594,0.917 0.865,1.125 true 0.125,0.844 0.458,1.031 0.333,0.188 10 true SST 2.854,1.771 3.063,1.948 0.208,0.177 10 false *a
*a 3/4 Turn


If enough space is available, use a torque wrench to tighten the oil filter sub-assembly.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


ii.

If enough space is not available to use a torque wrench, tighten the oil filter sub-assembly 3/4 of a turn by hand or with a common wrench.



Hide 6.ADD ENGINE OIL

a.

Add fresh engine oil.

Standard Engine Oil
Oil Grade Oil Viscosity (SAE)
API CF-4 or CF
(You may also use API CE or CD)
5W-30
10W-30
15W-40
20W-50

Standard Capacity
Item Specified Condition
Drain and refill without oil filter change 6.7 liters (7.1 US qts, 5.9 Imp. qts)
Drain and refill with oil filter change 7.2 liters (7.6 US qts, 6.3 Imp. qts)
Dry fill 8.4 liters (8.9 US qts, 7.4 Imp. qts)


b.

Install the oil filler cap.


Hide 7.INSPECT FOR OIL LEAK

a.

Start the engine. Make sure that there are no oil leaks from the areas that were worked on.


Hide 51442 8.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 51410 9.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY