12361
1.INSTALL FRONT ENGINE MOUNTING INSULATOR
Install the 2 front engine mounting insulators to the 2 front engine mounting brackets with the 2 nuts.
82121
2.INSTALL ENGINE WIRE
Install the engine wire to the engine assembly.
3.INSTALL NO. 2 ENGINE HANGER
4.REMOVE ENGINE FROM ENGINE STAND
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine assembly while it is suspended, as doing so is dangerous.
Attach an engine sling device and hang the engine assembly with a chain block.
Remove the engine assembly from the engine stand.
5.INSTALL ENGINE ASSEMBLY
Slowly lower the engine assembly into the engine compartment.
Install the engine assembly to the body with the 4 bolts and 4 nuts.
Make sure to tighten the side with the nut.
When installing a bolt with a claw (stopper), make sure that the claw (stopper) does not damage the body of the vehicle.
Remove the bolt and No. 2 engine hanger.
11354
6.INSTALL FLYWHEEL HOUSING DUST SEAL
11355
7.INSTALL REAR END PLATE
Install the rear end plate with the 2 bolts.
13405
8.INSTALL FLYWHEEL SUB-ASSEMBLY
Clean the bolts and bolt holes.
Using SST, hold the crankshaft.
Apply adhesive to 2 or 3 threads of each of the bolts.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Temporarily install the flywheel sub-assembly to the crankshaft with the 8 bolts.
Tighten the 8 bolts uniformly in several steps in the order shown in the illustration.
Do not start the engine for at least 1 hour after installation.
31250
9.INSTALL CLUTCH DISC ASSEMBLY
31210
10.INSTALL CLUTCH COVER ASSEMBLY
33030
11.INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY
37100
12.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
37140
13.INSTALL FRONT PROPELLER SHAFT ASSEMBLY
17410
14.INSTALL FRONT EXHAUST PIPE ASSEMBLY
27020
15.INSTALL GENERATOR ASSEMBLY
44320
16.INSTALL VANE PUMP ASSEMBLY
Temporarily install the vane pump assembly with the 2 bolts and nut.
Install the vane pump pulley to the vane pump assembly shaft.
Using SST, hold the pulley and install the nut.
88320
17.CONNECT COMPRESSOR ASSEMBLY WITH MAGNET CLUTCH (w/ Air Conditioning System)
Connect the compressor assembly with magnet clutch to the No. 1 compressor mounting bracket with the 4 bolts.
23271F
18.CONNECT FUEL HOSE
Connect the 2 fuel hoses to the injection pump assembly, and slide the 2 clamps to secure the hose.
87245A
19.CONNECT HEATER WATER HOSE ASSEMBLY
Install the bolt, connect the heater water hose assembly to the engine assembly, and slide the 2 clamps to secure the 2 hoses.
74431
20.INSTALL BATTERY TRAY
28800
21.INSTALL BATTERY
74451B
22.INSTALL BATTERY HOLD DOWN CLAMP
Install the battery clamp sub-assembly to the battery with the 2 nuts.
23.CONNECT WIRE HARNESS
Connect the engine room main wire to the battery positive cable with the nut.
Attach the clamp and connect the No. 2 engine wire with the 2 bolts.
Connect the 2 connectors to the engine room relay block sub-assembly.
Connect the wire to wire to the engine room relay block sub-assembly with the nut.
Attach the 2 clips and install the No. 1 relay block side cover to the engine room relay block sub-assembly.
Attach the 3 clips and install the No. 1 relay block upper cover to the engine room relay block sub-assembly.
17130
24.INSTALL INTAKE PIPE
17700
25.INSTALL AIR CLEANER CASE ASSEMBLY
Install the air cleaner case assembly with the 3 bolts.
17801
26.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
17705
27.INSTALL AIR CLEANER CAP AND HOSE
Install the air cleaner cap and hose.
Attach the 4 clips.
Tighten the hose clamp.
Connect the connector to the intake air temperature sensor and attach the 5 wire harness clamps.
82121
28.CONNECT ENGINE WIRE
Pass the engine wire into the cabin.
Attach the grommet to the body.
Make sure the direction of the grommet is as shown in the illustration.
Attach the 2 wire harness clamps to connect the engine wire to the wire harness bracket.
Attach the 2 clamps and connect the 3 connectors to the instrument panel wire.
Install the ECM.
Click hereEngine / Hybrid System>5L-E ENGINE CONTROL>ECM>INSTALLATION
55550
29.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
16400
30.INSTALL RADIATOR ASSEMBLY
16361A
31.INSTALL FAN AND GENERATOR V BELT
88310A
32.INSTALL COOLER COMPRESSOR V BELT (w/ Air Conditioning System)
44310A
33.INSTALL VANE PUMP V BELT
53301
34.INSTALL HOOD SUB-ASSEMBLY
Install the hood sub-assembly to the 2 hood hinge assemblies with the 4 bolts.
Connect the washer nozzle hose to the hood sub-assembly.
35.ADD POWER STEERING FLUID
36.ADD MANUAL TRANSMISSION OIL
37.ADD ENGINE OIL
38.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
39. BLEED AIR FROM FUEL SYSTEM
40.ADD ENGINE COOLANT
41. BLEED AIR FROM POWER STEERING SYSTEM
42.INSPECT POWER STEERING FLUID LEVEL
43.INSPECT FOR COOLANT LEAK
44.INSPECT FOR OIL LEAK
45.INSPECT FOR EXHAUST GAS LEAK
46.INSPECT FOR FUEL LEAK
47.CHECK ENGINE IDLE SPEED AND MAXIMUM SPEED
48.INSPECT ENGINE OIL LEVEL
51442
49.INSTALL NO. 2 ENGINE UNDER COVER
51410
50.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY