Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2016.01
RM3250E _54 Brake _038044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0178881 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display the DTC by blinking the ABS warning light.

WIRING DIAGRAM

C353287E01
0.5,4.313 4.167,4.51 3.667,0.198 10 false : CAN Communication Line 0.74,3.365 1.156,3.583 0.417,0.219 10 false ECM 3.573,3.375 3.99,3.594 0.417,0.219 10 false DLC3 3.271,3.375 3.688,3.594 0.417,0.219 10 false G8 0.906,0.698 1.385,0.896 0.479,0.198 10 false CANH 0.906,1.406 1.385,1.604 0.479,0.198 10 false CANL 1.094,2.167 1.354,2.375 0.26,0.208 10 false TC 5.979,0.688 6.458,0.885 0.479,0.198 10 false CANH 6,1.438 6.479,1.635 0.479,0.198 10 false CANL 5.26,1.917 5.677,2.135 0.417,0.219 10 false A3 5.542,1.906 7.115,2.302 1.573,0.396 10 false Skid Control ECU (Brake Actuator Assembly) 5.698,0.531 5.938,0.75 0.24,0.219 10 false 25 5.677,1.219 5.917,1.438 0.24,0.219 10 false 14 3.427,2.792 3.667,3.01 0.24,0.219 10 false CG 3.427,2.188 3.688,2.396 0.26,0.208 10 false TC 1.417,0.708 1.833,0.927 0.417,0.219 10 false G45 1.417,1.406 1.833,1.625 0.417,0.219 10 false G45 1.417,2.177 1.833,2.396 0.417,0.219 10 false G46 1.823,0.708 2.24,0.927 0.417,0.219 10 false G85 1.823,1.406 2.24,1.625 0.417,0.219 10 false G85 1.813,2.177 2.229,2.396 0.417,0.219 10 false G85 2.208,2.177 2.625,2.396 0.417,0.219 10 false G84 2.208,1.406 2.625,1.625 0.417,0.219 10 false G83 2.219,0.708 2.635,0.927 0.417,0.219 10 false G83 1.406,0.479 1.76,0.698 0.354,0.219 10 false 13*1 1.406,1.198 1.76,1.417 0.354,0.219 10 false 14*1 1.406,1.948 1.76,2.167 0.354,0.219 10 false 19*1 1.802,1.958 2.156,2.177 0.354,0.219 10 false 25*2 1.823,1.188 2.177,1.406 0.354,0.219 10 false 28*2 1.823,0.479 2.177,0.698 0.354,0.219 10 false 17*2 2.219,0.479 2.573,0.698 0.354,0.219 10 false 24*3 2.208,1.958 2.563,2.177 0.354,0.219 10 false 11*3 2.24,1.188 2.594,1.406 0.354,0.219 10 false 23*3 3.125,2.021 3.365,2.24 0.24,0.219 10 false 13 3.177,2.677 3.417,2.896 0.24,0.219 10 false 4 2.583,2.167 3,2.385 0.417,0.219 10 false G121 2.573,1.417 2.99,1.635 0.417,0.219 10 false G121 2.573,0.708 2.99,0.927 0.417,0.219 10 false G121 2.604,0.49 2.958,0.708 0.354,0.219 10 false 25*4 2.604,1.188 2.958,1.406 0.354,0.219 10 false 31*4 2.594,1.958 2.948,2.177 0.354,0.219 10 false 17*4 4.646,3.115 6.396,3.323 1.75,0.208 10 false *1: for 1TR-FE and 2TR-FE 4.625,3.396 6.594,3.594 1.969,0.198 10 false *2: for 1GD-FTV and 2GD-FTV 4.635,3.667 6.625,3.854 1.99,0.188 10 false *3: for 1KD-FTV and 2KD-FTV 4.646,3.938 6.396,4.146 1.75,0.208 10 false *4: for 5L-E

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform Test Mode (Signal Check) to acquire the rear differential lock identification information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

Result:
Proceed to
DTC is not output
DTC is output



DTC is not output

2.INSPECT DLC3

DTC is output

2.INSPECT DLC3
a.
C269109C35
0.115,1.49 0.479,1.719 0.365,0.229 1.635,1.813 1.823,1.49 true 1.302,0.281 1.573,0.792 true 1.073,0.198 1.417,0.438 0.344,0.24 10 false CG 1.521,1.844 1.833,2.042 0.313,0.198 10 false TC 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 0.198,1.521 0.51,1.719 0.313,0.198 10 false G8
*a Front view of DLC3


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G8-13 (TC) - G8-4 (CG) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

3.REPLACE ECM

NG

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
3.REPLACE ECM
a.
C269109C35
0.115,1.49 0.479,1.719 0.365,0.229 1.635,1.813 1.823,1.49 true 1.302,0.281 1.573,0.792 true 1.073,0.198 1.417,0.438 0.344,0.24 10 false CG 1.521,1.844 1.833,2.042 0.313,0.198 10 false TC 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 0.198,1.521 0.51,1.719 0.313,0.198 10 false G8
*a Front view of DLC3


Turn the ignition switch off.



c.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.


SST
09843-18040  

d.

Check that the ABS warning light are blinking.

OK:

The ABS warning light are blinking.



Result:
Proceed to
OK
NG



OK

END

NG

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the G46*1, G85*2, G84*3 or G121*4 ECM connector.

*1: for 1TR-FE and 2TR-FE

*2: for 1GD-FTV and 2GD-FTV

*3: for 1KD-FTV and 2KD-FTV

*4: for 5L-E



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1TR-FE and 2TR-FE:
Tester Connection Condition Specified Condition
G8-13 (TC) - G46-19 (TC) Always Below 1 Ω
G8-13 (TC) or G46-19 (TC) - Body ground Always 10 kΩ or higher

for 1GD-FTV and 2GD-FTV:
Tester Connection Condition Specified Condition
G8-13 (TC) - G85-25 (TC) Always Below 1 Ω
G8-13 (TC) or G85-25 (TC) - Body ground Always 10 kΩ or higher

for 1KD-FTV and 2KD-FTV:
Tester Connection Condition Specified Condition
G8-13 (TC) - G84-11 (TC) Always Below 1 Ω
G8-13 (TC) or G84-11 (TC) - Body ground Always 10 kΩ or higher


for 5L-E:
Tester Connection Condition Specified Condition
G8-13 (TC) - G121-17 (TC) Always Below 1 Ω
G8-13 (TC) or G121-17 (TC) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
C269109C36
0.115,1.49 0.479,1.719 0.365,0.229 1.302,0.281 1.573,0.792 true 1.073,0.198 1.417,0.438 0.344,0.24 10 false CG 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 0.208,1.521 0.521,1.719 0.313,0.198 10 false G8
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE ECM
a.
C269109C35
0.115,1.49 0.479,1.719 0.365,0.229 1.635,1.813 1.823,1.49 true 1.302,0.281 1.573,0.792 true 1.073,0.198 1.417,0.438 0.344,0.24 10 false CG 1.521,1.844 1.833,2.042 0.313,0.198 10 false TC 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 0.198,1.521 0.51,1.719 0.313,0.198 10 false G8
*a Front view of DLC3


Replace the ECM.

for 1KD-FTV: Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL

for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECM>REMOVAL

for 2GD-FTV: Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECM>REMOVAL

for 2KD-FTV: Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECM>REMOVAL

for 1TR-FE: Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>ECM>REMOVAL

for 2TR-FE: Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>ECM>REMOVAL

for 5L-E: Click hereEngine / Hybrid System>5L-E ENGINE CONTROL>ECM>REMOVAL


b.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.


SST
09843-18040  

c.

Check that the ABS warning light are blinking.

OK:

The ABS warning light are blinking.



Result:
Proceed to
OK
NG



OK

END

NG