Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK(for Double Cab) › from 2016.01
RM3250E _58 Vehicle Interior _038064 DOOR LOCK _0186384 REAR DOOR LOCK(for Double Cab) A

DOOR LOCK  REAR DOOR LOCK(for Double Cab)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 69318C 1.INSTALL DOOR LOCK WIRING HARNESS SEAL

NOTICE:
·

When reusing a removed rear door lock assembly LH, replace the door lock wiring harness seal with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.

·

Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the rear door lock assembly LH.



a.
B408935

Install a new door lock wiring harness seal to the rear door lock assembly LH.


Hide 69740D 2.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.
B408936C01
0,0 0,0 false
V113147

Install in this Direction


w/o Double Locking System:

i.

Attach the guide to install the rear door lock remote control cable assembly LH to the rear door lock assembly LH.



b.

w/ Double Locking System:

i.
B438943C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide to install the rear door lock remote control cable assembly LH to the rear door lock assembly LH.


ii.
B438942C01
0,0 0,0 false
V113147

Install in this Direction


Close the cover to attach the claw.



Hide 69780B 3.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.
B408937C01
0,0 0,0 false
V113147

Install in this Direction


w/o Double Locking System:

i.

Attach the guide to install the rear door inside locking cable assembly LH to the rear door lock assembly LH.



b.

w/ Double Locking System:

i.
B438945C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide to install the rear door inside locking cable assembly LH to the rear door lock assembly LH.


ii.
B438944C01
0,0 0,0 false
V113147

Install in this Direction


Close the cover to attach the claw.



Hide 69038A 4.INSTALL REAR DOOR LOCK COVER SUB-ASSEMBLY LH (w/o Double Locking System)

a.
B408938

Attach the clamp and claw to install the rear door lock cover sub-assembly LH.


Hide 69340 5.INSTALL REAR DOOR LOCK ASSEMBLY LH

a.

Apply MP grease to the sliding parts of the rear door lock assembly LH.


b.
B438937C01
1.906,0.802 2.167,0.552 2.167,0.552 2.417,0.552 true 2.354,0.469 2.667,0.667 0.313,0.198 10 true *a
*a Release Plate
V113147

Install in this Direction


Insert the rear door lock assembly LH into the rear door outside handle frame sub-assembly LH release plate, and set it to the rear door panel LH.

HINT:

Make sure that the rear door outside handle frame sub-assembly LH release plate is securely connected to the rear door lock assembly LH.



c.
B443248C02
0.083,0.094 0.396,0.25 0.313,0.156 10 false *A 0.083,1.917 0.396,2.073 0.313,0.156 10 false *B
*A w/o Double Locking System
*B w/ Double Locking System
V100135

"Torx" Screw
V100136

Connector


Using a T30 "TORX" socket wrench, install the rear door lock assembly LH with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.

Connect the connector.


Hide 67836H 6.INSTALL REAR DOOR LOCK CHILD PROTECTION COVER LH

Hide 68104 7.INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

Hide 67408E 8.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

Hide 68152C 9.INSTALL REAR DOOR GLASS RUN LH

Hide 67842E 10.INSTALL REAR DOOR SERVICE HOLE COVER LH

Hide 67604 11.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 69284D 12.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH

Hide 13.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL (w/ Power Window)

Hide 69260E 14.INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

Hide 74260 15.INSTALL REAR ARMREST ASSEMBLY LH

Hide 67674A 16.INSTALL REAR DOOR FRAME GARNISH LH

Hide 17.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION