Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR(for Double Cab) › from 2016.01
RM3250E _59 Vehicle Exterior _038077 DOOR / HATCH _0186370 REAR DOOR(for Double Cab) A

DOOR / HATCH  REAR DOOR(for Double Cab)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 75924C 2.INSTALL NO. 2 BLACK OUT TAPE LH (w/ Black Out Tape)

Hide 67837C 3.INSTALL REAR DOOR DUST PROOF SEAL

a.
B414920

Attach the claw to install 3 new front door dust proof seals.


Hide 67872 4.INSTALL REAR DOOR WEATHERSTRIP LH

a.
B414919

Attach the clip to install the rear door weatherstrip LH.


Hide 68640A 5.INSTALL REAR DOOR CHECK ASSEMBLY LH

a.

Apply MP grease to the sliding area of the rear door check assembly LH.


b.

When reusing a bolt:

i.

Clean the threads of the bolt with non-residue solvent.


ii.

Apply adhesive to the threads of the bolt (B).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.




c.
B414918C02
0,0 0,0 false
V100135

Bolt (A)
V100136

Bolt (B)


Install the rear door check assembly LH with the 2 bolts (A) and bolt (B).

Torque:
Bolt (A) : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Bolt (B) : 30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 67003C 6.INSTALL REAR DOOR PANEL CUSHION

a.
B414917

Attach the claw to install a new rear door panel cushion.


Hide 69204A 7.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding area of the rear door outside handle frame sub-assembly LH.


b.
B414921C01
2.375,0.552 2.375,0.229 2.375,0.229 2.563,0.229 true 2.635,1.073 2.385,1.073 2.385,1.073 2.385,0.875 true 1.01,1.052 1.313,1.052 1.313,1.052 1.313,0.792 true 0.865,0.938 1.073,1.156 0.208,0.219 10 true *a 2.552,0.125 2.76,0.344 0.208,0.219 10 true *b 2.573,0.969 2.781,1.188 0.208,0.219 10 true *b
*a Grommet
*b Guide
V113147

Install in this Direction


Attach the grommet and guide to install the rear door outside handle frame sub-assembly LH as shown in the illustration.


c.

Using a T30 "TORX" socket wrench, install the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242G 8.INSTALL REAR DOOR REAR OUTSIDE HANDLE PAD

a.
B414922C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the rear door rear outside handle pad.


Hide 69241G 9.INSTALL REAR DOOR FRONT OUTSIDE HANDLE PAD

a.
B414923C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the rear door front outside handle pad.


Hide 69240 10.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B414924C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear door outside handle assembly LH as shown in the illustration.


Hide 69227M 11.INSTALL REAR DOOR OUTSIDE HANDLE COVER

a.
B414925C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the rear door outside handle cover LH as shown in the illustration.


b.

Using a T30 "TORX" socket wrench, install the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69318C 12.INSTALL DOOR LOCK WIRING HARNESS SEAL

Hide 69740D 13.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

Hide 69780B 14.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH

Hide 69038A 15.INSTALL REAR DOOR LOCK COVER SUB-ASSEMBLY LH (w/o Double Locking System)

Hide 69340 16.INSTALL REAR DOOR LOCK ASSEMBLY LH

Hide 67836H 17.INSTALL REAR DOOR LOCK CHILD PROTECTION COVER LH

a.
B414911

Install the rear door lock child protection cover LH.


Hide 85720G 18.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (w/ Power Window)

Hide 69804 19.INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding area of the rear door window regulator sub-assembly LH.


b.

Temporarily install the temporarily bolt to the rear door window regulator sub-assembly LH.


c.

w/ Power Window:

i.

Install the rear door window regulator sub-assembly LH with the 3 bolts and temporarily bolt.

Torque:
Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Temporarily Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


ii.

Connect the connector.



d.

w/o Power Window:

Install the rear door window regulator sub-assembly LH with the 2 bolts and temporarily bolt.

Torque:
Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Temporarily Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)

B414910C01
0.406,0.052 0.719,0.25 0.313,0.198 10 true *A 3.917,0.073 4.229,0.271 0.313,0.198 10 true *B
*A w/o Power Window *B w/ Power Window
V100135

Bolt
V100136

Connector
V100137

Temporarily Bolt - -



Hide 68189 20.INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP LH

a.
B414909

Install the rear door quarter window weatherstrip LH to the rear door quarter window glass LH.


Hide 68124C 21.INSTALL REAR DOOR QUARTER WINDOW GLASS LH

a.
B414926C02
0.594,0.604 0.448,0.427 0.448,0.427 0.323,0.427 true 0.188,0.323 0.406,0.521 0.219,0.198 10 true *a
*a Emboss
V113147

Install in this Direction


Install the rear door quarter window glass LH together with the rear door quarter window weatherstrip LH as shown in the illustration.

HINT:

Make sure that the emboss on the rear door inner panel can be seen below rear door quarter window weatherstrip LH inner lip.



Hide 75740 22.INSTALL REAR DOOR BELT MOULDING ASSEMBLY LH

Hide 68104 23.INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

a.
B414927C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Insert the rear door glass sub-assembly LH as shown in the illustration.


b.
B414928

Install the rear door glass sub-assembly LH to the rear door window regulator sub-assembly LH as shown in the illustration.

NOTICE:

Be careful not to damage the rear door glass sub-assembly LH.



Hide 67408E 24.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

a.
B414905C02
0,0 0,0 false
V100135

Bolt
V100136

Screw


Install the rear door window division bar sub-assembly LH with the 2 bolts.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


b.

Lift up the rear door weatherstrip LH and install the screw.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 68152C 25.INSTALL REAR DOOR GLASS RUN LH

a.
B414904

Attach the guide to install a new rear door glass run LH.


Hide 26.INSTALL SCREW GROMMET

a.
B414903

Attach the claw to install 2 new screw grommets.


Hide 67842E 27.INSTALL REAR DOOR SERVICE HOLE COVER LH

a.

Apply new butyl tape to the rear door panel.


b.
B414929C01
0.646,0.635 0.646,0.448 0.646,0.448 0.49,0.448 true 2.75,0.635 2.75,0.448 2.75,0.448 2.854,0.448 true 2.844,0.375 3.052,0.573 0.208,0.198 10 true *a 0.323,0.344 0.531,0.542 0.208,0.198 10 true *a
*a Reference Point


Attach the clamp.


c.

Pass the rear door inside locking cable assembly LH and rear door lock remote control cable assembly LH through a new rear door service hole cover LH, and then attach the rear door service hole cover LH using the reference points on the rear door panel.

HINT:
·

Securely install the rear door service hole cover LH to prevent wrinkles and air bubbles.

·

There should be no wrinkles or folds after installing the rear door service hole cover LH.

·

After installing the rear door service hole cover LH, check the seal quality.




Hide 68174A 29.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH

a.
B414930

Install a new rear door inner glass weatherstrip LH to the rear door trim board sub-assembly LH and fold down the claw in the directions indicated by the arrows in the illustration.


Hide 69206C 30.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.
B414931C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and guide to install the rear door inside handle sub-assembly LH to the rear door trim board sub-assembly LH.


Hide 67604 31.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B412114C02
1.719,0.344 1.99,0.344 1.99,0.344 2.521,0.917 true 1.76,1.885 2.125,1.885 2.125,1.885 2.531,1.375 true 1.531,0.24 1.792,0.448 0.26,0.208 10 true *1 1.573,1.76 1.833,1.969 0.26,0.208 10 true *2
*1 Rear Door Inside Locking Cable Assembly LH
*2 Rear Door Lock Remote Control Cable assembly LH
V113147

Install in this Direction


Attach the clamp to connect the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH as shown in the illustration.


b.
B414932C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide as shown in the illustration.


c.
B414933

Attach the clip to install the rear door trim board sub-assembly LH.


d.
B414897

Install the 3 screws.


Hide 69284D 32.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH

a.
B414934

Attach the claw to install the rear door inside handle bezel plug LH.


Hide 84810D 33.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (w/ Power Window)

Hide 34.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL (w/ Power Window)

a.

Connect the connector.


b.
B414935C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and clip to install the rear power window regulator switch assembly with rear door armrest base panel as shown in the illustration.


Hide 69260E 35.INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

a.
B412121C02
0.698,1.854 0.938,1.854 0.938,1.854 0.938,1.26 false 3.146,0.719 3.385,0.917 0.24,0.198 10 false *a 2.708,0.396 3.021,0.594 0.313,0.198 10 false *b 0.5,1.75 0.813,1.948 0.313,0.198 10 false *1
*1 Plate
*a Front
*b 30°


With the door window fully closed, install the plate and rear door window regulator handle with the snap ring as shown in the illustration.


Hide 74260 36.INSTALL REAR ARMREST ASSEMBLY LH

a.
B414936C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and clip to install the rear armrest assembly LH.


Hide 67674A 37.INSTALL REAR DOOR FRAME GARNISH LH

a.
B414892

Attach the clip and claw to install the rear door frame garnish LH.


Hide 38.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION