Home › Engine / Hybrid System › 5L-E ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3250E _51 Engine / Hybrid System _049910 5L-E ENGINE CONTROL _0245156 ECD SYSTEM C

5L-E ENGINE CONTROL  ECD SYSTEM  P1222  Throttle Motor Circuit Range/Performance  


DESCRIPTION

Throttle control motor is operated by the ECM and opens and closes the throttle valve.

The fully open position of the throttle valve is detected by the throttle open switch which is mounted on the venturi assembly.

If this DTC is stored, the ECM shuts down the power for the throttle control motor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1222 Throttle Motor Circuit Range/Performance
Either condition is met (1 trip detection logic):
·

Open or short in throttle control motor circuit.

·

Open or short in throttle open switch circuit.


·

Open or short in throttle control motor circuit

·

Throttle control motor (Venturi assembly)

·

Intake restrictor valve

·

Open or short in throttle open switch circuit

·

Throttle open switch (Venturi assembly)

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A379044E02
0.396,5.083 1.469,5.281 1.073,0.198 10 false FL MAIN 0.385,4.281 1.458,4.479 1.073,0.198 10 false J/B-B 0.646,2.323 0.906,2.5 0.26,0.177 10 false 2B 0.677,2.125 0.938,2.302 0.26,0.177 10 false 1 0.813,2.521 1.885,2.719 1.073,0.198 10 false EFI MAIN NO. 1 1.677,3.375 2.75,3.573 1.073,0.198 10 false EFI MAIN NO. 1 6.375,1.76 6.833,1.958 0.458,0.198 10 false LU+B 3.5,2.333 3.76,2.51 0.26,0.177 10 false 2N 5.5,0.708 5.76,0.885 0.26,0.177 10 false 6 3.51,3.115 3.771,3.292 0.26,0.177 10 false 2P 3.542,2.906 3.802,3.083 0.26,0.177 10 false 9 1.177,3.573 1.438,3.75 0.26,0.177 10 false 2J 1.302,3.365 1.563,3.542 0.26,0.177 10 false 5 1.656,3.813 3.74,4.031 2.083,0.219 10 false Instrument Panel Junction Block 6.365,1.292 6.823,1.49 0.458,0.198 10 false LU-A 6.365,0.813 6.823,1.01 0.458,0.198 10 false LU+A 6.375,2.24 6.833,2.438 0.458,0.198 10 false LU-B 5.927,2.229 6.385,2.427 0.458,0.198 10 false C127 5.927,1.76 6.385,1.958 0.458,0.198 10 false C127 5.927,1.292 6.385,1.49 0.458,0.198 10 false C127 5.927,0.813 6.385,1.01 0.458,0.198 10 false C127 5.938,4.135 6.396,4.333 0.458,0.198 10 false C128 5.927,3.125 6.385,3.323 0.458,0.198 10 false G121 5.927,5.135 6.385,5.333 0.458,0.198 10 false C127 6.365,5.135 6.823,5.333 0.458,0.198 10 false E01 6.354,4.146 6.813,4.344 0.458,0.198 10 false THOP 6.354,3.115 6.813,3.313 0.458,0.198 10 false MREL 4.135,2.875 5.531,3.083 1.396,0.208 10 false Throttle Control Motor 4.125,2.698 5.521,2.906 1.396,0.208 10 false C135 4.385,4.49 5.781,4.698 1.396,0.208 10 false C136 4.385,4.677 5.781,4.885 1.396,0.208 10 false Throttle Open Switch 4.51,4.031 4.771,4.208 0.26,0.177 10 false 1 5.458,4.031 5.719,4.208 0.26,0.177 10 false 2 4.219,2.219 4.479,2.396 0.26,0.177 10 false 5 4.208,1.333 4.469,1.51 0.26,0.177 10 false 2 5.49,1.667 5.75,1.844 0.26,0.177 10 false 3 5.5,1.177 5.76,1.354 0.26,0.177 10 false 4 5.49,2.125 5.75,2.302 0.26,0.177 10 false 1 6.021,0.604 6.281,0.781 0.26,0.177 10 false 17 6.01,1.073 6.271,1.25 0.26,0.177 10 false 16 6.021,1.563 6.281,1.74 0.26,0.177 10 false 15 6,2.021 6.26,2.198 0.26,0.177 10 false 14 6,2.927 6.26,3.104 0.26,0.177 10 false 10 6.01,3.927 6.271,4.104 0.26,0.177 10 false 15 6.042,4.927 6.302,5.104 0.26,0.177 10 false 7 6.49,6.083 6.948,6.281 0.458,0.198 10 false ECM 2.667,2.479 3.427,2.677 0.76,0.198 10 false EFI NO. 1 0.563,5.885 1.635,6.083 1.073,0.198 10 false Battery 3.521,2.125 3.781,2.302 0.26,0.177 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT THROTTLE OPEN SWITCH
a.
A106810C01
0.135,0.115 0.448,0.313 0.313,0.198 10 false *a
*a Component without harness connected
(Throttle Open Switch)


Disconnect the throttle open switch connector.


b.

Remove the venturi assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
1 - 2 Always Below 1 Ω
1 - 2 Always 10 kΩ or higher


HINT:

The throttle open switch is integrated with the venturi assembly. If the throttle open switch is replaced, the venturi assembly must be replaced in whole.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (THROTTLE OPEN SWITCH - BODY GROUND, ECM - THROTTLE OPEN SWITCH)

NG

2.CHECK HARNESS AND CONNECTOR (THROTTLE OPEN SWITCH - BODY GROUND, ECM - THROTTLE OPEN SWITCH)
a.

Disconnect the throttle open switch connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C136-2 - C128-15 (THOP) Always Below 1 Ω
C136-1 - Body ground Always Below 1 Ω
C136-2 or C128-15 (THOP) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (THROTTLE CONTROL MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TERMINAL VOLTAGE (THROTTLE CONTROL MOTOR)
a.
A221614C74
0.51,1.396 0.896,1.656 0.385,0.26 1.677,1.188 1.156,0.844 true 2.083,1.885 1.719,1.5 true 0.542,1.448 0.927,1.625 0.385,0.177 10 false C135 0.833,0.719 1.177,0.917 0.344,0.198 10 false +B1 0.073,0.094 0.271,0.25 0.198,0.156 10 false *a 2,1.906 2.333,2.073 0.333,0.167 10 false +B2
*a Front view of wire harness connector
(to Throttle Control Motor)


Disconnect the throttle control motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
C135-2 (+B1) - Body ground Always 11 to 14 V
C135-5 (+B2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.INSPECT THROTTLE CONTROL MOTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE CONTROL MOTOR - INSTRUMENT PANEL JUNCTION BLOCK)

4.INSPECT THROTTLE CONTROL MOTOR
a.

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM)
a.

Disconnect the throttle control motor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C135-6 (LU+A) - C127-17 (LU+A) Always Below 1 Ω
C135-4 (LU-A) - C127-16 (LU-A) Always Below 1 Ω
C135-3 (LU+B) - C127-15 (LU+B) Always Below 1 Ω
C135-1 (LU-B) - C127-14 (LU-B) Always Below 1 Ω
C135-6 (LU+A) or C127-17 (LU+A) - Body ground and other terminals Always 10 kΩ or higher
C135-4 (LU-A) or C127-16 (LU-A) - Body ground and other terminals Always 10 kΩ or higher
C135-3 (LU+B) or C127-15 (LU+B) - Body ground and other terminals Always 10 kΩ or higher
C135-1 (LU-B) or C127-14 (LU-B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR