The body ECU receives switch signals from the power window regulator master switch assembly and driver door key cylinder lock or unlock switch signals from the front door lock assembly LH*1 or RH*2. The body ECU activates the door lock motor on each door according to these signals.
*1: for LHD
*2: for RHD
If the body ECU has been replaced, it is necessary to initialize the body ECU.*1
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.*2
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION
*1: w/ Automatic Light Control System
*2: w/ Door Control Battery
Check door lock operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
| Result | Proceed to |
|---|---|
| All doors cannot be locked by power window regulator master switch assembly (w/ Entry and Start System) | A |
| All doors cannot be locked by power window regulator master switch assembly (w/o Entry and Start System) | B |
| All doors cannot be locked by driver door key cylinder | C |
A
B
C
Check the power window control system.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK
Power window control system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Replace the power window regulator master switch assembly.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check door lock operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Power door lock control system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the power window regulator master switch assembly.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL
Inspect the power window regulator master switch assembly.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for LHD
*2: for RHD
Disconnect the K5*1 or J11*2 power window regulator master switch assembly connector.
Disconnect the G27 body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K5-2 (L) - G27-19 (L1) | Always | Below 1 Ω |
| K5-2 (L) or G27-19 (L1) - Body ground | Always | 10 kΩ or higher |
| K5-8 (UL) - G27-12 (UL1) | Always | Below 1 Ω |
| K5-8 (UL) or G27-12 (UL1) - Body ground | Always | 10 kΩ or higher |
| K5-1 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J11-8 (L) - G27-19 (L1) | Always | Below 1 Ω |
| J11-8 (L) or G27-19 (L1) - Body ground | Always | 10 kΩ or higher |
| J11-2 (UL) - G27-12 (UL1) | Always | Below 1 Ω |
| J11-2 (UL) or G27-12 (UL1) - Body ground | Always | 10 kΩ or higher |
| J11-9 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
NG
*1: for LHD
*2: for RHD
Remove the front door lock assembly LH*1 or RH*2.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
Inspect the front door lock assembly LH*1 or RH*2.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for LHD
*2: for RHD
Disconnect the K1*1 or J1*2 front door lock assembly LH*1 or RH*2 connector.
Disconnect the G27 body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K1-9 (L) - G27-18 (L2) | Always | Below 1 Ω |
| K1-9 (L) or G27-18 (L2) - Body ground | Always | 10 kΩ or higher |
| K1-10 (UL) - G27-11 (UL2) | Always | Below 1 Ω |
| K1-10 (UL) or G27-11 (UL2) - Body ground | Always | 10 kΩ or higher |
| K1-7 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J1-6 (L) - G27-18 (L2) | Always | Below 1 Ω |
| J1-6 (L) or G27-18 (L2) - Body ground | Always | 10 kΩ or higher |
| J1-5 (UL) - G27-11 (UL2) | Always | Below 1 Ω |
| J1-5 (UL) or G27-11 (UL2) - Body ground | Always | 10 kΩ or higher |
| J1-8 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J1-6 (L) - G27-18 (L2) | Always | Below 1 Ω |
| J1-6 (L) or G27-18 (L2) - Body ground | Always | 10 kΩ or higher |
| J1-5 (UL) - G27-4 (UL3) | Always | Below 1 Ω |
| J1-5 (UL) or G27-4 (UL3) - Body ground | Always | 10 kΩ or higher |
| J1-8 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
NG