Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK(for Smart Cab) › from 2016.03
RM3250E _58 Vehicle Interior _038064 DOOR LOCK _0186385 REAR DOOR LOCK(for Smart Cab) A

DOOR LOCK  REAR DOOR LOCK(for Smart Cab)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the upper access panel lock assembly or lower access panel lock assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Memorize steering angle neutral point Pre-crash safety system (Click here)

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION (w/ Airbag System)

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

for Type A:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

for Type B:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION

for Type C:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Airbag System)

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 73233 3.REMOVE LAP BELT OUTER ANCHOR COVER

Hide 67604 4.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 73178A 5.REMOVE SEAT BELT ANCHOR COVER CAP

Hide 73220 6.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH

Hide 67674A 7.REMOVE REAR DOOR FRAME GARNISH LH

Hide 69360L 8.REMOVE UPPER ACCESS PANEL LOCK ASSEMBLY LH

a.
B408940C01
0,0 0,0 false
V100135

Bolt
V100136

Connector


Disconnect the connector and detach the clamp.


b.

Remove the 3 bolts and upper access panel lock assembly LH.


c.
B408941

Disconnect the cable from the access panel lock remote control assembly LH and detach the clamp.


Hide 69390D 9.REMOVE LOWER ACCESS PANEL LOCK ASSEMBLY LH

a.
B408942

Disconnect the cable from the access panel lock remote control and detach the clamp.


b.

Disconnect the connector and detach the clamp.


c.
B408943

Using a T30 "TORX" socket wrench, remove the 3 bolts.


d.
B408944C03
0.698,1.729 0.896,1.729 0.896,1.729 1.177,1.365 true 0.49,1.625 0.688,1.823 0.198,0.198 10 true *1
*1 Grommet


Using a screwdriver, pry up the grommet from the stud bolt.


e.
B408945

Detach the hook and remove the lower access panel lock assembly LH.