Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM(w/ Urea SCR System) › from 2016.03
RM3250E _51 Engine / Hybrid System _038005 2GD-FTV ENGINE CONTROL _0262511 ECD SYSTEM(w/ Urea SCR System) C

2GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P0069  Manifold Absolute Pressure - Barometric Pressure Correlation  


DESCRIPTION

To detect atmospheric pressure, the atmospheric pressure sensor built into the ECM is used in the common rail system. Following the changes in the atmospheric pressure, the ECM corrects the fuel injection volume, timing and duration, and adjusts the common rail internal fuel pressure to optimize combustion.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0069 Manifold Absolute Pressure - Barometric Pressure Correlation After the ignition switch is turned to ON, the difference between the atmospheric pressure sensor output and manifold absolute pressure sensor output is more than 14 kPa for 0.5 seconds (2 trip detection logic).
·

Manifold absolute pressure sensor

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0069
·

Atmosphere Pressure

·

MAP



HINT:
·

Turn the ignition switch to ON and check the Atmosphere Pressure and MAP items in the Data List. If the atmospheric pressure displayed on the GTS differs greatly from the actual atmospheric pressure (standard: 101 kPa), the sensor (atmospheric pressure sensor or manifold absolute pressure sensor) is malfunctioning.

·

If DTC P0069 is stored, the following symptoms may appear:

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0069 1 second elapses after ignition switch turned from off to ON (starter remains off)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ Urea SCR System)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ Urea SCR System)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0069)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0069 is output A
DTC P0069 and other DTCs are output B


HINT:

If codes other than DTC P0069 are output, perform troubleshooting for those DTCs first.




A

2.INSPECT MANIFOLD ABSOLUTE PRESSURE SENSOR

B

2.INSPECT MANIFOLD ABSOLUTE PRESSURE SENSOR
HINT:

Before inspecting the manifold absolute pressure sensor, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / MAP.

Powertrain > Engine > Data List
Tester Display
MAP
50003 234 4

e.

Read the value.

OK:

Same value as the actual atmospheric pressure.



Result:
Proceed to
OK
NG



OK

3.CHECK DTC OUTPUT

NG

3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTC.

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for 30 seconds or more.


f.

Turn the ignition switch to ON for 1 second or more.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P0069 is output A
No DTC is output B



A

B

END