The injector assemblies are installed in the cylinder head and inject fuel into the cylinders based on the signals from the ECM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0201 | Injector Circuit / Open - (Cylinder 1) | Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds) (1 trip detection logic). | ·
Open or short in No. 1 injector assembly circuit ·
No. 1 injector assembly ·
ECM |
Comes on | DTC stored |
| P0202 | Injector Circuit / Open - (Cylinder 2) | Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds) (1 trip detection logic). | ·
Open or short in No. 2 injector assembly circuit ·
No. 2 injector assembly ·
ECM |
Comes on | DTC stored |
| P0203 | Injector Circuit / Open - (Cylinder 3) | Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds) (1 trip detection logic). | ·
Open or short in No. 3 injector assembly circuit ·
No. 3 injector assembly ·
ECM |
Comes on | DTC stored |
| P0204 | Injector Circuit / Open - (Cylinder 4) | Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds) (1 trip detection logic). | ·
Open or short in No. 4 injector assembly circuit ·
No. 4 injector assembly ·
ECM |
Comes on | DTC stored |
| P062D | No. 1 Fuel Injector Driver Circuit Performance | ECM internal error (1 trip detection logic). | ECM | Comes on | DTC stored |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0201
P0202 P0203 P0204 P062D |
Idling for 5 seconds or more |
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ Urea SCR System)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ Urea SCR System)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ Urea SCR System)>REGISTRATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0201, P0202, P0203 or P0204 is output | A |
| DTC P062D is output | B |
B
A
| *a | Component with harness connected
(ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C59-5 (+BD1) - C60-1 (E1) | Ignition switch ON | 11 to 14 V |
| C59-4 (+BD2) - C60-1 (E1) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Inspect the EDU relay.
Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the EDU relay.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off for 30 seconds.
Start the engine and idle it for 5 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Check the DTCs output on the GTS.
The cylinder with the malfunctioning injector assembly can be determined based on the output DTCs.
If the DTC P0201 is output, check the No. 1 injector assembly circuit.
If the DTC P0202 is output, check the No. 2 injector assembly circuit.
If the DTC P0203 is output, check the No. 3 injector assembly circuit.
If the DTC P0204 is output, check the No. 4 injector assembly circuit.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the injector assembly connectors for all cylinders.
If only the injector assembly connector of the malfunctioning cylinder is disconnected, the engine will start and there will be rough idling. Therefore, disconnect all injector assembly connectors before inspecting the waveform.
Start the engine.
Check the waveform of the injector assembly connectors using an oscilloscope.
| *a | Front view of wire harness connector
(Injector Assembly) |
*b | No. 1 Injector Assembly Connector |
| *c | No. 2 Injector Assembly Connector | *d | No. 3 Injector Assembly Connector |
| *e | No. 4 Injector Assembly Connector | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C101-1 - C101-2 | Cranking | Correct waveform is as shown |
| C102-1 - C102-2 | Cranking | Correct waveform is as shown |
| C103-1 - C103-2 | Cranking | Correct waveform is as shown |
| C104-1 - C104-2 | Cranking | Correct waveform is as shown |
Reconnect the injector assembly connectors for all cylinders.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the injector assembly of the cylinder relevant to the DTC.
Click hereEngine / Hybrid System>2GD-FTV FUEL>FUEL INJECTOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the injector assembly of the cylinder relevant to the DTC.
Click hereEngine / Hybrid System>2GD-FTV FUEL>FUEL INJECTOR>REMOVAL
When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.
Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>2GD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Register the injector compensation code.
Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ Urea SCR System)>REGISTRATION
| Tester Display |
|---|
| Injector Compensation |
Perform the injector pilot quantity learning.
Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ Urea SCR System)>REGISTRATION
| Tester Display |
|---|
| Pilot Quantity Learning |
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the injector assembly connectors for all cylinders.
If only the injector assembly connector of the malfunctioning cylinder is disconnected, the engine will start and there will be rough idling. Therefore, disconnect all injector assembly connectors before inspecting the waveform.
Start the engine.
Check the waveform of the injector assembly connectors using an oscilloscope.
| *a | Component with harness connected
(ECM) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C57-6 (#1D+) - C57-7 (#1D-) | Cranking | Correct waveform is as shown |
| C57-1 (#2D+) - C57-2 (#2D-) | Cranking | Correct waveform is as shown |
| C58-7 (#3D+) - C58-6 (#3D-) | Cranking | Correct waveform is as shown |
| C57-5 (#4D+) - C57-4 (#4D-) | Cranking | Correct waveform is as shown |
Reconnect the injector assembly connectors for all cylinders.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine and idle it for 5 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT