Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM(w/ Urea SCR System) › from 2016.03
RM3250E _51 Engine / Hybrid System _038005 2GD-FTV ENGINE CONTROL _0262511 ECD SYSTEM(w/ Urea SCR System) C

2GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P204B  Reductant Pressure Sensor Circuit Range/Performance  


DESCRIPTION

Refer to DTC P208B.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ Urea SCR System)>P208B

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P204B Reductant Pressure Sensor Circuit Range/Performance When the urea pump is not rotating (urea pump operation check complete and not being filled), the pressure sensor value is outside of a fixed range (1 trip detection logic). Pressure sensor (urea pump) Comes on DTC stored

Related Data List
DTC No. Data List
P204B Reductant Pressure

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P204B Ignition switch to ON for 5 seconds or more

CAUTION / NOTICE / HINT

NOTICE:
Handling the urea injector set
·

The urea injector set is a precision instrument. Take necessary precautions for installation and shipping. Do not use the part if it has been struck or dropped.

·

If the urea solution remaining inside the urea injector set dries out, it may become unable to inject urea solution. Therefore, conduct urea tube with heater assembly installation and removal quickly.

·

If the urea solution dries out and deposition occurs, urea may cling to the O-ring of the pipe and cause seal problems. Therefore, clean the urea tube with heater assembly and intake port of the urea injector set with water before attaching them.

·

Perform this procedure in an environment where urea solution will not freeze.



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P204B)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P204B is output A
DTC P204B and other DTCs are output* B


HINT:

*: If any other DTCs (CAN communication malfunctions or open/short circuits) are output, perform troubleshooting for those DTCs first.




A

2.CHECK AROUND BOTTOM VEHICLE

B

2.CHECK AROUND BOTTOM VEHICLE
a.

Check around the bottom of the vehicle.

HINT:

If the urea solution dries on an object, deposition occurs and leaves behind a white powder.


Area to check:

·

Areas connecting the urea pump and urea injector set.

·

Perforations in the urea tank sub-assembly.

·

Connectors not connected properly.

·

Clogging of the cooling fins of the urea injector set.

HINT:

If the cooling fins are clogged with foreign matter, remove the foreign matter and clean the cooling fins.




b.

Repair any trouble areas.


Result:
Proceed to
NEXT



NEXT

3.PERFORM ACTIVE TEST USING GTS (PRESSURE SENSOR CHECK)
3.PERFORM ACTIVE TEST USING GTS (PRESSURE SENSOR CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Pump Check (Backward).


d.

Perform the Active Test.

Powertrain > Engine > Active Test
Tester Display
Reductant Pump Check (Backward)
50004 234 322

e.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Purge / Data List / Diesel Exhaust / Reductant Pressure.


f.

After executing the Active Test, check the Reductant Pressure.

Powertrain > Engine > Active Test
Active Test Display
Reductant Purge
Data List Display
Reductant Pressure
50004 234 323 1132
Standard:

Approximately 0 kPa



g.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Filling (Pressure Keep) / Data List / Diesel Exhaust / Reductant Pressure.


h.

After executing the Active Test, check the Reductant Pressure.

HINT:

Perform the Active Test until the pressure stabilizes (may take from 5 to 60 seconds).


Powertrain > Engine > Active Test
Active Test Display
Reductant Filling (Pressure Keep)
Data List Display
Reductant Pressure
50004 234 321 1132
OK:

400 to 600 kPa



Result:
Proceed to
OK
NG



OK

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

4.REPLACE UREA PUMP
4.REPLACE UREA PUMP

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

d.

Turn the ignition switch off for 30 seconds or more.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Wait for 5 seconds or more.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END