Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2016.03
RM3250E _51 Engine / Hybrid System _053992 STOP AND START _0262513 STOP AND START SYSTEM M

STOP AND START  STOP AND START SYSTEM  REGISTRATION  


PROCEDURE

Hide 1.ECU EXCHANGE

NOTICE:
·

After replacing the engine stop and start ECU, upload the number of starter operations and total number of engine starts to the new engine stop and start ECU using the GTS.

·

for Automatic Transmission:

When the engine stop and start ECU is replaced, check the electromagnetic oil pump.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Utility / ECU Exchange.

Powertrain > Stop and Start > Utility
Tester Display
ECU Exchange
50005 227 4411

e.

According to the GTS display, download the previous status (the number of starter operations and total number of engine starts) from the old engine stop and start ECU to the GTS.


f.

Replace the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL


g.

According to the GTS display, upload the previous status (the number of starter operations and total number of engine starts) from the GTS to the new engine stop and start ECU.


Hide 2.CLEAR NUMBER OF STARTER OPERATIONS

NOTICE:
·

After the starter assembly is replaced, be sure to clear the number of starter operations stored in the engine stop and start ECU.

·

When the starter assembly is replaced, "ST NO. 1 relay" and "ST NO. 2 relay" must be also replaced.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Utility / Starter Exchange.

Powertrain > Stop and Start > Utility
Tester Display
Starter Exchange
50005 227 130

Hide 3. TOTAL NUMBER OF ENGINE STARTS RESET

NOTICE:

After the flywheel sub-assembly is replaced, be sure to clear the number of total number of engine starts stored in the engine stop and start ECU.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Utility / Total Number of Engine Starts Reset.

Powertrain > Stop and Start > Utility
Tester Display
Total Number of Engine Starts Reset
50005 227 4410

Hide 4.RESET AIR CONDITIONING INFORMATION

NOTICE:

After replacing the engine stop and start ECU or air conditioning amplifier assembly, initialization of the air conditioning information in the engine stop and start ECU is necessary.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Utility / Reset A/C Information.

Powertrain > Stop and Start > Utility
Tester Display
Reset A/C Information
50005 227 2104

Hide 5.LEARNING AIR CONDITIONING INFORMATION

HINT:

When initialization of the air conditioning information is complete, air conditioning information learning is automatically performed. If the learning cannot be performed properly, inspect the CAN communication system.


Hide 6.CLEAR THE ZERO POINT CALIBRATION DATA

NOTICE:
·

After replacing the engine stop and start ECU or airbag sensor assembly, perform deceleration sensor zero point clear and calibration.

·

Once the zero point is stored, it cannot be overwritten until the data is cleared. Be sure to perform zero point clear and calibration after replacing the airbag sensor assembly.



a.

Turn the ignition switch off.


b.

for Automatic Transmission:

Move the shift lever to P and apply the parking brake.

for Manual Transmission:

Move the shift lever to neutral and apply the parking brake.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.

HINT:

Do not start the engine.



e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Clear.

Powertrain > Stop and Start > Utility
Tester Display
Deceleration Sensor Zero Point Clear
50005 227 4174
NOTICE:

When the deceleration sensor zero point is cleared, the system information stored in the engine stop and start ECU is also cleared. If the vehicle is driven for 5 seconds or more at 3 km/h (2 mph) or more in this condition, the engine stop and start ECU will store DTC P1589 and blink the stop and start cancel indicator light.



g.

Turn the ignition switch off.


Hide 7.PERFORM ZERO POINT CALIBRATION OF THE DECELERATION SENSOR

NOTICE:

Park the vehicle on a level surface (grade: +/-1%). Do not shake the vehicle or open/close any of the doors during zero point calibration. To avoid vibration caused by the engine idling, do not start the engine.


a.

Connect the GTS to the DLC3.


b.

for Automatic Transmission:

Check that the shift lever is in P and apply the parking brake.

for Manual Transmission:

Move the shift lever to neutral and apply the parking brake.


c.

Turn the ignition switch to ON.

HINT:

Do not start the engine.



d.

Check that the parking brake is applied.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Calibration.

Powertrain > Stop and Start > Utility
Tester Display
Deceleration Sensor Zero Point Calibration
50005 227 4147
HINT:

If DTC P1589 is stored, the stop and start cancel indicator light will blink.



g.

While keeping the vehicle stationary, follow the prompts on the GTS screen. Check that "Complete" is displayed on the GTS screen.

NOTICE:

If zero point calibration fails, perform the registration procedure again from "CLEAR THE ZERO POINT CALIBRATION DATA".



Hide 8.CLEAR THE INTEGRATED CURRENT VALUE

HINT:

After charging the battery, perform the integrated current value initialization.

If the Data List item "Integrated Current" indicates 0 or more, initialization is not necessary.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Utility / Integrated Current Value Initialization.

Powertrain > Stop and Start > Utility
Tester Display
Integrated Current Value Initialization
50005 227 4258

Hide 9.SWITCH BATTERY TYPE

NOTICE:

When the ECM is replaced on a vehicle with a non-specified battery, it is necessary to perform battery type switching.


a.

Check whether the battery is specified or not specified.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.

HINT:

Do not start the engine.



d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Stop and Start / Data List / Battery Type.

HINT:

Check the battery type (Specified/Other) recognized by the ECU.


Powertrain > Stop and Start > Data List
Tester Display
Battery Type
50003 227 421

f.

If the battery installed does not match the battery recognized by the ECM, switch to the battery type for the installed battery.

i.

Enter the following menus: Powertrain / Engine and ECT / Utility / Switch Battery Type.

Powertrain > Engine and ECT > Utility
Tester Display
Switch Battery Type
50005 234 4377


Hide 35200 10.CHECK ELECTROMAGNETIC OIL PUMP (for Automatic Transmission)

NOTICE:

When the electromagnetic oil pump or engine stop and start ECU is replaced, perform the "Electromagnetic Oil Pump" Active Test.


HINT:

This check is one of the final inspection items performed before returning the vehicle to the customer.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Move the shift lever to P.


d.

Turn the GTS on.


e.

Perform the "Electromagnetic Oil Pump" Active Test for 2 seconds.

Enter the following menus: Powertrain / Stop and Start / Active Test / Electromagnetic Oil Pump.

Powertrain > Stop and Start > Active Test
Tester Display
Electromagnetic Oil Pump
50004 227 15

f.

Check that the "Oper Permission (Electromagnetic Oil Pump)" Data List item is listed as "OK".

Enter the following menus: Powertrain / Stop and Start / Data List / Oper Permission (Electromagnetic Oil Pump).

Powertrain > Stop and Start > Data List
Tester Display
Oper Permission (Electromagnetic Oil Pump)
50003 227 426