Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2016.03
RM3250E _51 Engine / Hybrid System _053992 STOP AND START _0262513 STOP AND START SYSTEM J

STOP AND START  STOP AND START SYSTEM  STA Signal Circuit  


DESCRIPTION

While the engine is being cranked, a starter operation request signal is sent to terminal STA of the ECM.

HINT:

If there is an open in the STA circuit of the ECM, stop and start control will be prohibited after the third time the engine is started by stop and start control.

·

Stop and start control will be prohibited until the ignition switch is turned off.

·

The MIL will not illuminate.

·

If there is an open in the STA circuit of the ECM, the engine can still be started using the ignition or starter switch assembly (w/o Entry and Start System) or push start switch assembly (w/ Entry and Start System), as the ECM also receives the starter operation request signal from the engine stop and start ECU via CAN communication. (Stop and start control is prohibited as the reliability of the signal sent via CAN communication cannot be assured while the voltage drops during operation of the starter assembly.)



A289886E05
2.76,0.792 5.5,1.021 2.74,0.229 10 false Starter operation request signal 5.76,1.125 6.281,1.333 0.521,0.208 10 false CAN 1.26,2.198 1.781,2.406 0.521,0.208 10 false STA 0.823,3.594 2.156,3.906 1.333,0.313 10 false from ST NO. 2 Fuse 0.865,5.063 2.25,5.271 1.385,0.208 10 false for Starter Assembly 3.844,4.313 5.031,4.615 1.188,0.302 10 false ST NO. 2 4.25,1.74 5.302,2.125 1.052,0.385 10 false Starter operation request 1.25,1.135 1.771,1.344 0.521,0.208 10 false CAN 5.833,4.5 6.865,5.313 1.031,0.813 10 false : CAN Communication Line 5.75,2.208 6.271,2.417 0.521,0.208 10 false STA2 5.542,2.792 6.583,3.146 1.042,0.354 10 false Engine Stop and Start ECU 1.031,2.802 1.438,3.094 0.406,0.292 10 false ECM 2.375,2.385 2.896,2.594 0.521,0.208 10 false Open 4.25,2.396 5.271,2.729 1.021,0.333 10 false Starter operation request

WIRING DIAGRAM

A330989E08
5.427,0.625 5.885,0.823 0.458,0.198 10 false G127 5.51,0.427 5.823,0.625 0.313,0.198 10 false 13 5.427,1.021 5.885,1.219 0.458,0.198 10 false G127 5.51,0.833 5.823,1.031 0.313,0.198 10 false 14 5.865,0.656 6.479,0.854 0.615,0.198 10 false CANH 5.875,1.031 6.49,1.229 0.615,0.198 10 false CANL 1.271,0.646 1.885,0.844 0.615,0.198 10 false CANH 1.292,1.042 1.906,1.24 0.615,0.198 10 false CANL 1.792,0.438 2.104,0.635 0.313,0.198 10 false 17 1.802,0.844 2.115,1.042 0.313,0.198 10 false 28 1.375,1.5 1.833,1.698 0.458,0.198 10 false STA 5.521,1.292 5.833,1.49 0.313,0.198 10 false 23 5.885,1.5 6.344,1.698 0.458,0.198 10 false STA2 1.792,1.365 2.104,1.563 0.313,0.198 10 false 22 1.146,2.438 1.781,2.656 0.635,0.219 10 false ECM 1.146,2.281 1.604,2.479 0.458,0.198 10 false G85 2.281,3.063 3.354,3.26 1.073,0.198 10 false ST NO. 2 4.802,3.615 5.875,3.813 1.073,0.198 10 false ST NO. 2 4.417,3.208 4.573,3.406 0.156,0.198 10 false 2 4.073,3.99 4.229,4.188 0.156,0.198 10 false 3 4.427,3.99 4.583,4.188 0.156,0.198 10 false 1 4.063,3.208 4.219,3.406 0.156,0.198 10 false 5 0.938,4.771 1.646,4.979 0.708,0.208 10 false Battery 0.771,3.708 1.542,3.906 0.771,0.198 10 false FL MAIN 4.75,5.594 5.979,5.792 1.229,0.198 10 false Starter Assembly 4.74,5.438 5.323,5.604 0.583,0.167 10 false C141 4.115,5.344 4.573,5.542 0.458,0.198 10 false SL2 4.063,5.052 4.219,5.25 0.156,0.198 10 false 2 0.771,6.208 3.01,6.406 2.24,0.198 10 false : CAN Communication Line 5.188,2.406 6.948,2.823 1.76,0.417 10 false Engine Stop and Start ECU 5.427,1.49 5.885,1.688 0.458,0.198 10 false G126

PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Read the values displayed on the GTS when the engine starts.

OK:
Tester Display Condition Normal Condition
Starter Signal Ignition switch ON OFF
Engine start ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (ECM - ST NO. 2 RELAY)
2.CHECK HARNESS AND CONNECTOR (ECM - ST NO. 2 RELAY)
a.

Disconnect the G85 ECM connector.


b.

Remove the ST NO. 2 relay from the engine room relay block and junction block assembly.


c.

Disconnect the G126 engine stop and start ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G85-22 (STA) - ST NO. 2 relay terminal 2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR