Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.03
RM3250E _54 Brake _038044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0178882 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the ABS warning light remains on:

·

The skid control ECU (brake actuator assembly) connectors are disconnected from the skid control ECU (brake actuator assembly).

·

There is a malfunction in the skid control ECU (brake actuator assembly) internal circuit.

·

There is an open in the harness between the combination meter assembly and the skid control ECU (brake actuator assembly).

·

The ABS control system is defective.

·

w/ Rear Differential Lock:

The rear differential is locked.


HINT:

In some cases, the GTS cannot be used when the skid control ECU (brake actuator assembly) is abnormal.


WIRING DIAGRAM

C318223E16
0.833,0.75 1.448,0.948 0.615,0.198 10 false CANH 1.323,0.573 1.635,0.771 0.313,0.198 10 false 36 5.854,0.573 6.167,0.771 0.313,0.198 10 false 22 6.115,0.75 6.729,0.948 0.615,0.198 10 false CANH 0.844,1.323 1.458,1.521 0.615,0.198 10 false CANL 1.323,1.135 1.635,1.333 0.313,0.198 10 false 35 5.844,1.125 6.156,1.323 0.313,0.198 10 false 10 6.125,1.333 6.74,1.531 0.615,0.198 10 false CANL 0.219,5.833 0.531,6.031 0.313,0.198 10 false G9 0.229,6 1.417,6.427 1.188,0.427 10 false Combination Meter Assembly 5.854,4.333 6.167,4.531 0.313,0.198 10 false 25 6.115,2.042 6.573,2.24 0.458,0.198 10 false IG1 5.854,1.906 6.167,2.104 0.313,0.198 10 false 12 4.75,1.896 5.063,2.094 0.313,0.198 10 false *2 4.01,2.229 4.854,2.469 0.844,0.24 10 false IG1 NO. 3 2.042,2.031 3.052,2.26 1.01,0.229 10 false from IG Circuit 3.333,3.24 3.719,3.438 0.385,0.198 10 false IG31 3.719,3.156 3.875,3.354 0.156,0.198 10 false 1 4.781,3.146 5.094,3.344 0.313,0.198 10 false *1 2.26,3.677 2.719,3.875 0.458,0.198 10 false G127 2.719,3.677 4.604,3.927 1.885,0.25 10 false Engine Stop and Start ECU*1 5.583,5.844 5.896,6.042 0.313,0.198 10 false A4 5.583,6.031 7.146,6.615 1.563,0.583 10 false Skid Control ECU (Brake Actuator Assembly) 2.563,5.76 4.323,5.979 1.76,0.219 10 false : CAN Communication Line 1.594,6.177 3.458,6.438 1.865,0.26 10 false *1: w/ Stop and Start System 1.594,6.469 3.552,6.719 1.958,0.25 10 false *2: w/o Stop and Start System 6.115,4.469 6.729,4.667 0.615,0.198 10 false GND1

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

w/o Stop and Start System:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

DTC is not output

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

DTC is output

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.INSPECT BATTERY

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
a.
C306843C69
1.542,0.094 1.917,0.333 0.375,0.24 3.188,1.406 3.188,1.115 3.188,1.115 2.458,0.948 true 3.104,1.448 3.385,1.656 0.281,0.208 10 false IG1 1.646,0.125 1.948,0.333 0.302,0.208 10 false A4 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Disconnect the A4 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A4-12 (IG1) - Body ground Ignition switch ON 10.5 to 16 V*1
11 to 14 V*2


*1: w/ Stop and Start System

*2: w/o Stop and Start System



Result:
Proceed to
OK
NG (w/ Stop and Start System)
NG (w/o Stop and Start System)



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG (w/ Stop and Start System)

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

NG (w/o Stop and Start System)

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.
C306843C62
1.49,0.073 1.885,0.323 0.396,0.25 0.198,1.625 0.208,1.417 0.208,1.417 0.615,1.208 true 0.073,1.688 0.688,1.885 0.615,0.198 10 false GND1 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 1.594,0.115 2.052,0.313 0.458,0.198 10 false A4
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-25 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK (w/o Rear Differential Lock)
OK (w/ Rear Differential Lock)
NG



OK (w/o Rear Differential Lock)

7.READ VALUE USING GTS (ABS WARNING LIGHT)

OK (w/ Rear Differential Lock)

6.CHECK FOR DIFFERENTIAL SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.CHECK FOR DIFFERENTIAL SYSTEM
a.

Reconnect the A4 skid control ECU (brake actuator assembly) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Four Wheel Drive / Trouble Codes.


f.

Check for DTCs.

Powertrain > Four Wheel Drive > Trouble Codes
50001 363

Result:
Proceed to
DTCs are not output
DTCs are output



DTCs are not output

7.READ VALUE USING GTS (ABS WARNING LIGHT)

DTCs are output

GO TO DIFFERENTIAL SYSTEM (DIAGNOSTIC TROUBLE CODE CHART)

7.READ VALUE USING GTS (ABS WARNING LIGHT)
a.

Reconnect the A4 skid control ECU (brake actuator assembly) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light OFF or ON OFF: Warning light off
ON: Warning light on
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
ABS Warning Light
50003 105 51
g.

Check the GTS display condition of the ABS warning light.

Result:
Proceed to
Display of the Data List remains OFF
Display of the Data List remains ON




Display of the Data List remains OFF

Display of the Data List remains ON