Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2016.03
RM3250E _51 Engine / Hybrid System _053992 STOP AND START _0262513 STOP AND START SYSTEM J

STOP AND START  STOP AND START SYSTEM  Backup Boost Converter Circuit  


DESCRIPTION

A backup boost converter is built into the engine stop and start ECU. The backup boost converter helps maintain the power source voltage when the engine is restarted by stop and start control.

This prevents various functions such as the navigation system from failing if the power source voltage drops due to the battery voltage dropping when the engine is restarted by stop and start control. If a DTC is output, troubleshoot the DTC first.

HINT:

A relay function and fuse function are provided in the backup boost converter.

If there is a malfunction in any of the electrical system circuits connected to the backup boost converter, the fuse and relay functions shut off the malfunctioning circuit to protect other circuits (remains shut off until next trip).

When the electrical system circuit is shut off, power to the circuit is cut off, causing any systems connected to the circuit to be disabled.

The fuse function is reset* when the ignition switch is turned off. If the malfunction still exists in the electrical system circuit that has been shut off by the relay function, it will be shut off again by the relay and fuse functions the next time the ignition switch is turned to ON.

*: A semiconductor fuse self-resets according to electric signals.


The backup boost converter supplies power to:
·

Radio and display receiver assembly

·

Air conditioning control assembly

·

Skid control ECU (brake actuator assembly)

·

Spiral with sensor cable sub-assembly

·

Combination meter assembly

·

Millimeter wave radar sensor assembly

·

Forward recognition camera

·

Body ECU


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and total number of engine starts and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

for Automatic Transmission:

When the engine stop and start ECU is replaced, check the electromagnetic oil pump.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK PROBLEM SYMPTOMS
a.

Determine the trouble area by referring to the table below.

Effect on Vehicle Trouble Area/Cause Fail-safe DTC Output Stop and start cancel indicator light Symptom Proceed to
When the engine is restarted by stop and start control, the following symptoms may occur.
·

The audio and visual system is reset

·

The combination meter assembly fades out

·

Air conditioning system cannot be operated

·

Lane departure alert system cannot be operated

·

Pre-crash safety system cannot be operated

·

Road sign assist system cannot be operated


Backup boost converter internal malfunction
·

Internal power source malfunction

·

Internal power source overvoltage

·

Duty error

·

Communication cycle error


Stop and start control prohibited P323B Blinks Converter output voltage cannot be boosted when the engine is restarted A
Battery voltage drop
Systems on the converter output side do not operate
B42 terminal:
The audio and visual system will not function
IG41 terminal: None of the following will operate
·

Air conditioning system

·

Lane departure Alert system

·

Pre-crash safety system

·

Road sign assist system

·

Systems whose power is supplied from the body ECU


Overcurrent applied to an output terminal (output terminal relay circuit is shutoff) Stop and start control is prohibited
(Connected ECUs or sensors may detect power source malfunction DTCs)
B22C0 Blinks Systems do not operate as power supply from the converter is cut off A
Systems do not operate
(Due to converter input side malfunction)
IG1 terminal: None of the following operate
·

Skid control ECU (brake actuator assembly)

·

Spiral with sensor cable sub-assembly

·

Air conditioning control assembly

·

Systems whose power is supplied from the body ECU


IG2 terminal: The combination meter assembly will not function
ACC terminal: The audio will not function
Converter input circuit malfunction
·

Open or short to GND in IG1 circuit

·

Open or short to GND in IG2 circuit

·

Open or short to GND in ACC circuit


Stop and start control prohibited - Does not blink (Blinks when communication error DTCs are stored) Systems do not operate as power supply from the converter is cut off B
Systems on the converter output side do not operate
(varies depending on the malfunctioning relay circuit the converter detected)
AC42 terminal: The audio and visual system will not function
IG12 terminal: The combination meter assembly will not function
Malfunction in circuits the converter supplies power to
(between the converter and ECUs or sensors)
·

Open or short in the combination meter assembly circuit


Related systems do not operate as the relay circuit in the converter is turned off - Does not blink (Blinks when communication error DTCs are stored) Systems do not operate as power supply from the converter is cut off B
All of the following will operate
·

Radio and display receiver assembly

·

Skid control ECU (brake actuator assembly)

·

Spiral with sensor cable sub-assembly

·

Combination meter assembly

·

Air conditioning control assembly

·

Millimeter wave radar sensor assembly

·

Forward recognition camera

·

Systems whose power is supplied from the body ECU


·

Open in BBC fuse circuit

·

Short in converter circuit

·

Backup boost converter malfunction


Stop and start control prohibited P0617 Does not blink (Due to disabled meter/gauge system) All systems that the converter supplies power to do not operate (see circuit diagram) A
P323B
The audio does not function
(until the ignition switch is turned off)
Excessive audio volume
Data List item "State of BBC" displays "BBC Overcurrent" while the circuit is protected
The relay circuit in the converter is turned off to cut off power supply to the navigation system (Returns to normal when the ignition switch is turned off) - Does not blink If overcurrent is detected in the navigation system, system operation is disabled while the ignition switch is ON
(Returns to normal when the ignition switch is turned off)
C
The audio and visual system cannot be turned off (short between AC42 and +B)
The combination meter assembly cannot be turned off (short between IG12 and +B)
Communication error DTCs may be stored due to short between IG31 and +B
HINT:

Varies depending on the number of times an open occurs in the +B circuit


Converter circuit malfunction
·

Short between AC42 and +B

·

Short between IG31 and +B

·

Short between IG12 and +B


- - Does not blink The converter cannot shut off power source when the ignition switch is turned off B
Ignition switch does not turn to ACC (short between ACC and +B)
Ignition switch does not turn off (short between IG1 or IG2 and +B)
Engine stop and start ECU power source circuit malfunction
·

Short between ACC and +B

·

Short between IG1 and +B

·

Short between IG2 and +B


- - Does not blink
·

Ignition switch does not turn to ACC

·

Ignition switch does not turn off


B


Result:
Proceed to
A
B
C



A

B

2.CHECK ENGINE STOP AND START ECU (POWER SOURCE CIRCUIT)

C

5.CHECK AUDIO AND VISUAL SYSTEM
2.CHECK ENGINE STOP AND START ECU (POWER SOURCE CIRCUIT)
a.
A346343C07
1.458,0.354 1.906,0.573 0.448,0.219 1.5,2.479 1.948,2.698 0.448,0.219 0.979,1.229 0.531,1.24 true 1,1.583 0.552,1.594 true 1.563,3.76 1.573,4.188 true 2.052,3.74 2.406,4.167 true 1.417,3.75 1.073,4.177 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 1.521,0.385 1.979,0.583 0.458,0.198 10 false G125 0.167,1.156 0.573,1.385 0.406,0.229 10 false BIN2 0.177,1.521 0.583,1.75 0.406,0.229 10 false BIN1 1.563,2.51 2.021,2.708 0.458,0.198 10 false G127 1.438,4.229 1.896,4.427 0.458,0.198 10 false ACC 2.333,4.24 2.792,4.438 0.458,0.198 10 false IG1 0.917,4.219 1.375,4.417 0.458,0.198 10 false IG2
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


Disconnect the G125 and G127 engine stop and start ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G125-1 (BIN2) - Body ground Always 9.5 to 14 V
G125-3 (BIN1) - Body ground Always 9.5 to 14 V



c.

Turn the ignition switch to ACC.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G127-19 (ACC) - Body ground Ignition switch ACC 9.5 to 14 V



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G127-21 (IG1) - Body ground Ignition switch ON 9.5 to 14 V
G127-18 (IG2) - Body ground Ignition switch ON 9.5 to 14 V



g.

Turn the ignition switch off.


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G127-21 (IG1) - Body ground Ignition switch off 0 to 1 V
G127-19 (ACC) - Body ground Ignition switch off 0 to 1 V
G127-18 (IG2) - Body ground Ignition switch off 0 to 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
a.

Disconnect the connector from the corresponding system ECU/sensor.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Radio and Display Receiver Assembly
Tester Connection Condition Specified Condition
G127-12 (B42) - G40-4 (+B1) Always Below 1 Ω
G127-15 (AC42) - G40-3 (ACC1) Always Below 1 Ω
G127-12 (B42) - Body ground Always 10 kΩ or higher
G127-15 (AC42) - Body ground Always 10 kΩ or higher
G40-4 (+B1) - Body ground Always 10 kΩ or higher
G40-3 (ACC1) - Body ground Always 10 kΩ or higher

Skid Control ECU (Brake Actuator Assembly)
Tester Connection Condition Specified Condition
G127-1 (IG31) - A4-12 (IG1) Always Below 1 Ω
G127-1 (IG31) - Body ground Always 10 kΩ or higher
A4-12 (IG1) - Body ground Always 10 kΩ or higher

Spiral with Sensor Cable Sub-assembly
Tester Connection Condition Specified Condition
G127-1 (IG31) - G21-4 (IG) Always Below 1 Ω
G127-1 (IG31) - Body ground Always 10 kΩ or higher
G21-4 (IG) - Body ground Always 10 kΩ or higher

Combination Meter Assembly
Tester Connection Condition Specified Condition
G127-10 (IG12) - G9-22 (IG+) Always Below 1 Ω
G127-10 (IG12) - Body ground Always 10 kΩ or higher
G9-22 (IG+) - Body ground Always 10 kΩ or higher

Air Conditioning Control Assembly
Tester Connection Condition Specified Condition
G127-3 (IG41) - G32-2 (IG+) Always Below 1 Ω
G127-3 (IG41) - Body ground Always 10 kΩ or higher
G32-2 (IG+) - Body ground Always 10 kΩ or higher

Millimeter Wave Radar Sensor Assembly
Tester Connection Condition Specified Condition
G127-3 (IG41) - A64-8 (IGB) Always Below 1 Ω
G127-3 (IG41) - Body ground Always 10 kΩ or higher
A64-8 (IGB) - Body ground Always 10 kΩ or higher

Forward Recognition Camera
Tester Connection Condition Specified Condition
G127-3 (IG41) - Q4-7 (IGB) Always Below 1 Ω
G127-3 (IG41) - Body ground Always 10 kΩ or higher
Q4-7 (IGB) - Body ground Always 10 kΩ or higher

Instrument Panel Junction Block Assembly (Body ECU)
Tester Connection Condition Specified Condition
G127-3 (IG41) - 2D-5 Always Below 1 Ω
G127-3 (IG41) - Body ground Always 10 kΩ or higher
2D-5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK ENGINE STOP AND START ECU (EACH ECU OR SENSOR POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ENGINE STOP AND START ECU (EACH ECU OR SENSOR POWER SOURCE CIRCUIT)
a.

Disconnect the connector from the corresponding system ECU/sensor.


b.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage at the corresponding terminals.


Standard Voltage:
Tester Connection Condition Specified Condition
G40-4 (+B1) - Body ground Always 10.5 to 16 V



c.

Turn the ignition switch to ACC.


d.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage at the corresponding terminals.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
G40-3 (ACC1) - Body ground Ignition switch ACC 10.5 to 16 V



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage at the corresponding terminals.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
G21-4 (IG) - Body ground Ignition switch ON 10.5 to 16 V
A4-12 (IG1) - Body ground Ignition switch ON 10.5 to 16 V
G9-22 (IG+) - Body ground Ignition switch ON 10.5 to 16 V
G32-2 (IG+) - Body ground Ignition switch ON 10.5 to 16 V
A64-8 (IGB) - Body ground Ignition switch ON 10.5 to 16 V
Q4-7 (IGB) - Body ground Ignition switch ON 10.5 to 16 V
2D-5 - Body ground Ignition switch ON 10.5 to 16 V



Result:
Proceed to
OK
NG



OK

CHECK POWER SOURCE CIRCUIT (POWER SOURCE CIRCUIT OF RELATED SYSTEM)

NG

5.CHECK AUDIO AND VISUAL SYSTEM
a.

Turn the ignition switch off and wait for 1 minute.


b.

Turn the ignition switch to ON.


c.

Lower the audio volume.


d.

Check if the audio and visual system operates normally.

OK:

Audio and visual system operates normally.



Result:
Proceed to
NG
OK



NG

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY)

OK

END

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the G127 engine stop and start ECU connector.


b.

Disconnect the G40 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G127-12 (B42) - Body ground Always 10 kΩ or higher
G40-4 (+B1) - Body ground Always 10 kΩ or higher
G127-15 (AC42) - Body ground Always 10 kΩ or higher
G40-3 (ACC1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR