Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.03
RM3250E _54 Brake _038044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0178882 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Downhill Assist Control Indicator Light does not Come ON  


DESCRIPTION

Even if the downhill assist control switch is pressed, the downhill assist control indicator light blinks and downhill assist control does not activate under the following conditions:

·

for Automatic Transmission:

Shift position is P.

·

The 4WD control switch (transfer position switch) set to H2.

·

w/ Rear Differential Lock:

The rear differential is locked.

·

The vehicle speed is 30 km/h (19 mph) or more.

·

The brake system is malfunctioning.

·

Temperature of the brake actuator assembly increases and the downhill assist control is temporarily canceled.


WIRING DIAGRAM

C324770E10
6.115,0.531 6.729,0.729 0.615,0.198 10 false CANH 0.823,0.531 1.24,0.729 0.417,0.198 10 false CANH 5.833,0.313 6.031,0.563 0.198,0.25 10 false 22 1.354,0.313 1.552,0.563 0.198,0.25 10 false 36 0.833,1.094 1.25,1.292 0.417,0.198 10 false CANL 6.135,1.094 6.552,1.292 0.417,0.198 10 false CANL 5.844,0.906 6.042,1.156 0.198,0.25 10 false 10 1.354,0.927 1.552,1.177 0.198,0.25 10 false 35 6.115,1.833 6.531,2.031 0.417,0.198 10 false GND1 5.823,1.646 6.021,1.896 0.198,0.25 10 false 25 2.573,2.219 4,2.76 1.427,0.542 10 false A.D.D. Position Switch (Differential Motor Actuator Assembly) 2.292,2.219 2.625,2.448 0.333,0.229 10 false C7 0.354,3.781 2.188,4.063 1.833,0.281 10 false 4 Wheel Drive Control ECU 5.833,3.073 6.031,3.323 0.198,0.25 10 false 3 0.156,1.75 0.406,1.969 0.25,0.219 10 false G9 0.938,3.219 1.354,3.417 0.417,0.198 10 false ADD 1.354,3.083 1.552,3.333 0.198,0.25 10 false 2 6.135,3.24 6.552,3.438 0.417,0.198 10 false EXI 6.125,4.26 6.625,4.552 0.5,0.292 10 false HDCS 5.833,4.083 6.031,4.333 0.198,0.25 10 false 27 2.979,4.677 5.042,4.938 2.063,0.26 10 false Downhill Assist Control Switch 2.677,4.677 3.042,4.927 0.365,0.25 10 false G72 5.479,4.51 5.844,4.76 0.365,0.25 10 false A4 5.49,4.76 7.156,5.177 1.667,0.417 10 false Skid Control ECU (Brake Actuator Assembly) 0.542,5.313 2.708,5.646 2.167,0.333 10 false : CAN Communication Line 0.406,1.75 1.583,2.188 1.177,0.438 10 false Combination Meter Assembly 0.052,3.781 0.344,4 0.292,0.219 10 false C39 2.844,1.688 3.208,1.938 0.365,0.25 10 false GND 3.625,1.688 4,1.938 0.375,0.25 10 false ADD 2.604,1.667 2.76,1.875 0.156,0.208 10 false 4 4.094,1.646 4.25,1.854 0.156,0.208 10 false 3 3.094,4.073 3.292,4.323 0.198,0.25 10 false 1 4.281,4.083 4.479,4.333 0.198,0.25 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

DTC is not output

2.CHECK HARNESS AND CONNECTOR (EXI TERMINAL)

DTC is output

2.CHECK HARNESS AND CONNECTOR (EXI TERMINAL)
a.

Turn the ignition switch to ON.


b.

Turn the 4WD control switch (transfer position switch) to H4 or L4.


c.

Turn the ignition switch off.


d.
C306843C71
1.542,0.104 1.917,0.344 0.375,0.24 0.729,0.26 0.896,0.26 0.896,0.26 1.104,0.833 true 0.479,0.177 0.854,0.406 0.375,0.229 10 false EXI 1.625,0.146 1.927,0.354 0.302,0.208 10 false A4 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Disconnect the A4 skid control ECU (brake actuator assembly) connector.


e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A4-3 (EXI) - Body ground
·

Ignition switch ON

·

4WD control switch (transfer position switch) set to H4 or L4


Below 1.5 V



g.

Turn the ignition switch off.


h.

Reconnect the A4 skid control ECU (brake actuator assembly) connector.


i.

Turn the ignition switch to ON.


j.

Turn the 4WD control switch (transfer position switch) to H2.


k.

Turn the ignition switch off.


l.

Disconnect the A4 skid control ECU (brake actuator assembly) connector.


m.

Turn the ignition switch to ON.


n.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A4-3 (EXI) - Body ground
·

Ignition switch ON

·

4WD control switch (transfer position switch) set to H2


11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT DOWNHILL ASSIST CONTROL SWITCH

NG

7.CHECK HARNESS AND CONNECTOR (EXI TERMINAL CIRCUIT)
3.INSPECT DOWNHILL ASSIST CONTROL SWITCH
a.

Turn the ignition switch off.


b.

c.

Inspect the downhill assist control switch.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>DOWNHILL ASSIST CONTROL SWITCH>INSPECTION

OK:

The downhill assist control switch operates normally.



Result:
Result
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - DOWNHILL ASSIST CONTROL SWITCH)

NG

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - DOWNHILL ASSIST CONTROL SWITCH)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-27 (HDCS) - G72-4 Always Below 1 Ω
A4-27 (HDCS) or G72-4 - Body ground Always 10 kΩ or higher
G72-1 - Body ground Always Below 1 Ω


Result:
Result
OK
NG




OK

5.PERFORM ACTIVE TEST USING GTS (DOWNHILL ASSIST CONTROL LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.PERFORM ACTIVE TEST USING GTS (DOWNHILL ASSIST CONTROL LIGHT)
a.

Reconnect the A4 skid control ECU (brake actuator assembly) connector.


b.

Reconnect the G72 downhill assist control switch connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


g.

According to the display on the GTS, perform the Active Test.


Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Downhill Assist Control Light Downhill assist control indicator light Indicator light ON/OFF Observe combination meter assembly
Vehicle condition: Vehicle stopped
h.

When performing the ABS Warning Light Active Test, check Downhill assist control indicator light in the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Downhill Assist Control Light Downhill assist control indicator light ON or OFF OFF: Downhill assist control indicator light off
ON: Downhill assist control indicator light on
-
Chassis > ABS/VSC/TRC > Active Test
Active Test Display
Downhill Assist Control Light
Data List Display
Downhill Assist Control Light
50004 105 66 59
Result:
Result Proceed to
Downhill assist control indicator light in the Data List does not change using the Active Test A
Downhill assist control indicator light in the Data List turns ON/OFF using the Active Test B



A

B

6.INSPECT COMBINATION METER ASSEMBLY
6.INSPECT COMBINATION METER ASSEMBLY
a.

Turn the ignition switch off.


b.

Perform Active Test of the combination meter assembly using the GTS.


Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. Downhill Assist Control
50004 122 49
c.

Check the combination meter assembly.


OK:

The Downhill assist control indicator light turns on or off in accordance with the GTS.


Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (EXI TERMINAL CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the C7 A.D.D. position switch (differential motor actuator assembly) connector.


c.

Disconnect the C39 4 wheel drive control ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-3 (EXI) - C7-3 (ADD) Always Below 1 Ω
A4-3 (EXI) - C39-2 (ADD) Always Below 1 Ω
A4-3 (EXI) - Body ground Always 10 kΩ or higher
C7-3 (ADD) - Body ground Always 10 kΩ or higher
C39-2 (ADD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT DIFFERENTIAL MOTOR ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EXI TERMINAL CIRCUIT)

8.INSPECT DIFFERENTIAL MOTOR ACTUATOR ASSEMBLY
a.

Remove the A.D.D. position switch (differential motor actuator assembly).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>AUTOMATIC DISCONNECTING DIFFERENTIAL ACTUATOR>REMOVAL


b.

Inspect the A.D.D. position switch (differential motor actuator assembly).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>AUTOMATIC DISCONNECTING DIFFERENTIAL ACTUATOR>INSPECTION

OK:

The A.D.D. position switch (differential motor actuator assembly) operates normally.



Result:
Proceed to
OK
NG



OK

NG