Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) › from 2016.03
RM3250E _57 Power Source / Network _038063 NETWORKING _0262514 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) D

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  SYSTEM DESCRIPTION  


BRIEF DESCRIPTION


a.

The Controller Area Network (CAN) is a serial data communication system for real time application. It is a vehicle multiplex communication system which has a high communication speed and the ability to detect malfunctions.

C351786E02
0.958,2.188 1.094,2.188 1.094,2.188 1.313,1.802 true 4.354,3.406 4.583,3.406 4.583,3.406 4.76,3.052 true 0.229,2.104 0.927,2.604 0.698,0.5 10 false CAN Main Bus 3.448,2.677 3.906,2.875 0.458,0.198 10 false ECU 5.313,2.656 5.771,2.854 0.458,0.198 10 false ECU 3.542,3.313 5.073,3.51 1.531,0.198 10 false CAN Branch 1.427,3.635 3.781,3.917 2.354,0.281 10 false : CAN Main Line (CANH) 1.427,4.083 3.198,4.354 1.771,0.271 10 false : CAN Main Line (CANL) 4.833,3.635 6.771,3.917 1.938,0.281 10 false : CAN Branch Line (CANH) 4.833,4.063 6.854,4.344 2.021,0.281 10 false : CAN Branch Line (CANL) 1.667,2.688 2.125,2.885 0.458,0.198 10 false ECU


b.

Using the CANH and CANL bus wires as a pair, CAN communication is performed using a voltage differential. (A base voltage is applied to the pair of wires and a voltage differential is created when communicating.)


c.

Many ECUs or sensors installed on the vehicle operate by sharing information and communicating with each other.


d.

The CAN has two resistors of 120 Ω which are necessary to enable communication.



DEFINITION OF TERMS


a.

CAN main wire

i.

The CAN main wire is a wire harness between the 2 termination circuits on the bus (communication wire). This is the main bus in the CAN communication system.



b.

CAN branch wire

i.

The CAN branch wire is a wire harness which diverges from the main wire to an ECU or sensor.



c.

Termination circuits

i.

Two resistors of 120 Ω are installed in parallel across the ends of the CAN main bus wires. They are called terminating resistors. These resistors allow the changes of the voltage differential between the CAN bus wires to be accurately judged. To allow proper function of CAN communication, it is necessary to have both terminating resistors installed. Since the two resistors are installed in parallel, this results in a measurement of approximately 60 Ω.




ECUS OR SENSORS WHICH COMMUNICATE VIA CAN COMMUNICATION SYSTEM


a.

V Bus

i.

Central Gateway ECU (Network Gateway ECU)


ii.

DLC3



b.

Bus 2

i.

Central Gateway ECU (Network Gateway ECU)


ii.

ECM


iii.

Certification ECU (Smart Key ECU Assembly)*1


iv.

Air Conditioning Amplifier Assembly*2, *3


v.

4 Wheel Drive Control ECU*4


vi.

Brake Actuator Assembly (Skid Control ECU)


vii.

Airbag Sensor Assembly


viii.

Headlight Leveling ECU Assembly*5


ix.

Engine Stop and Start ECU*6


x.

Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)


xi.

Combination meter assembly

*1: w/ Entry and Start System

*2: for Automatic Air Conditioning System

*3: for Manual Air Conditioning System

*4: for 4WD

*5: for LED Headlight or w/ Headlight Cleaner System

*6: w/ Stop and Start System




c.

Bus 3

i.

Central Gateway ECU (Network Gateway ECU)


ii.

Radio and Display Receiver Assembly*1


iii.

Navigation Receiver Assembly*2

*1: w/ Audio and Visual System (for Radio and Display Type)

*2: w/ Navigation System




d.

Bus 5

i.

Central Gateway ECU (Network Gateway ECU)


ii.

Forward Recognition Camera


iii.

Millimeter Wave Radar Sensor Assembly




CIRCUIT DESCRIPTION


a.

The V bus has a termination circuit with a resistor of 60 Ω.


b.

The bus 2, bus 3 and bus 5 each have termination circuits with two resistors of 120 Ω.



TROUBLESHOOTING REMARKS


a.

DTCs for the CAN communication system can be checked using the GTS. The DLC3 is connected to the CAN communication system, but no DTCs exist regarding problems in the DLC3 or the DLC3 branch wires. If there is a malfunction in the DLC3 or the DLC3 branch wires, ECUs on the CAN cannot output DTCs to the GTS.



DIAGNOSTIC TROUBLE CODES FOR CAN COMMUNICATION SYSTEM


HINT:

See Diagnosis System

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



DIAGNOSTIC TROUBLE CODES FOR CAN COMMUNICATION SYSTEM


a.

In the CAN communication system, the shape of all connectors connected to the CAN junction connector is the same.

The connectors connected to the CAN junction connector can be distinguished by the colors of the bus wire and the connecting side of the connector.

HINT:

Refer to "Terminals of ECU" for bus wire color or the connecting side of the connector.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>TERMINALS OF ECU